Sharp Mx2310u User Guide

2-12
COPIER
Contents
This section explains the basic procedures for making copies, including selection of the copy ratio and other copy 
settings.
MAKING COPIES
USING THE AUTOMATIC DOCUMENT FEEDER TO 
MAKE COPIES
This section explains how to make copies (1-sided copies of 1-sided originals) using the automatic document feeder.
BASIC PROCEDURE FOR MAKING 
COPIES
1
Place the originals face up in the 
document feeder tray with the edges 
aligned evenly.
Insert the originals all the way into the document...

2-13
COPIER
Contents
3
Set the number of copies (number of 
sets) with the numeric keys.
 Up to 999 copies (sets) can be set.
 A single copy can be made even if 0 appears for the number of copies.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
4
Press the [COLOUR START] key or the [BLACK & WHITE START] key.
Even if a colour mode is selected, copying will take place in black and white if the [BLACK & WHITE START] key is 
pressed.
To cancel...

2-14
COPIER
Contents
MAKING A COPY USING THE DOCUMENT GLASS
To make a copy of a book or other thick original that cannot be scanned with the automatic document feeder, open the 
automatic document feeder and place the original on the document glass. This section explains how to make a copy 
(1-sided copy of a 1-sided original) using the document glass.
1
Open the automatic document feeder, 
place the original face down on the 
document glass, and then gently close 
the automatic document feeder.
 Align...

2-15
COPIER
Contents
3
Set the number of copies (number of 
sets) with the numeric keys.
 Up to 999 copies (sets) can be set.
 A single copy can be made even if 0 appears for the number of copies.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
4
Press the [COLOUR START] key or the [BLACK & WHITE START] key.
Normally copying will start.
Depending on the copy settings (2-sided copying, etc.), copying may not begin until all originals have been...

2-16
COPIER
Contents
AUTOMATIC 2-SIDED COPYING
USING THE AUTOMATIC DOCUMENT FEEDER TO 
MAKE 2-SIDED COPIES
Copying onto both sides of a sheet saves paper.
Automatic 2-sided copying of 1-sided 
originalsAutomatic 2-sided copying of 2-sided 
originals1-sided copying of 2-sided originals
1
Place the originals face up in the 
document feeder tray with the edges 
aligned evenly.
Insert the originals all the way into the document feeder tray.
Multiple originals can be placed in the document feeder tray. 
The...

2-17
COPIER
Contents Using the [Binding Change] key
4
Check the paper to be used and the 
colour mode.
Make sure that the desired paper (tray) and colour mode are 
selected.
 To change the paper (tray), touch the [Paper Select] key.
☞PAPER TRAYS (page 2-11)
 To change the colour mode, touch the [Colour Mode] key.
☞COPY COLOUR MODES (page 2-21)
Depending on the size of the placed original, there may be cases where the same size of paper as the original is not 
selected automatically. In this event,...

2-18
COPIER
Contents
AUTOMATIC 2-SIDED COPYING USING THE 
DOCUMENT GLASS
Automatic 2-sided copying of 1-sided 
originals
1
Open the automatic document feeder, 
place the original face down on the 
document glass, and then gently close 
the automatic document feeder.
 Align the corner of the original with the tip of the arrow mark 
 on the document glass scale.
 Place the original in the appropriate position for its size as 
shown above.
 After placing the original, be sure to close the automatic...

2-19
COPIER
Contents
3
Select the 2-sided copy mode.
(1) Touch the [1-Sided to 2-Sided] key.
(2) Touch the [OK] key.
  When the document cover is installed, the [2-Sided to 2-Sided] key and the [2-Sided to 1-Sided] key is not 
displayed.
 The [2-Sided to 2-Sided] key and [2-Sided to 1-Sided] key cannot be used when copying from the document glass.
4
Check the paper to be used and the 
colour mode.
Make sure that the desired paper (tray) and colour mode are 
selected.
 To change the paper (tray), touch...

2-20
COPIER
Contents
7
Remove the original and place the next original, and then press the [COLOUR 
START] key or the [BLACK & WHITE START] key.
Repeat this step until all originals have been scanned.
For the second original and following originals, use the same [START] key as you did for the first original.
8
Touch the [Read-End] key.
To cancel scanning of the original and copying...
Press the [STOP] key ( ).
System Settings (Administrator): Initial Status Settings (2-Sided Copy)
The default 2-sided...

2-21
COPIER
Contents
COPY COLOUR MODES
The colour mode of the [COLOUR START] key is normally set to [Full Colour] so that copying takes place in full colour 
mode when the [COLOUR START] key is pressed. If colour originals are mixed together with black & white originals, set 
the colour mode to [Auto] to have the colour mode change appropriately for each original.
Touch the [Colour Mode] key in the base screen to open the following screen.
Touch the key of the desired colour mode and then touch the [OK]...