Sharp MX M450N User Manual

							8-1
CHAPTER 8
KEY OPERATOR 
PROGRAMS
This chapter explains the key operator programs that are used by the
administrator of the machine to customize certain functions and
settings.
Page
KEY OPERATOR PROGRAMS .............................................................. 8-2
OKEY OPERATOR PROGRAM LIST................................................ 8-2
OUSING THE KEY OPERATOR PROGRAMS ................................. 8-3
OKEY OPERATOR PROGRAMS ...................................................... 8-4
OOPERATION SETTINGS ................................................................ 8-4
OFAX SETTINGS .............................................................................. 8-5
OPRINTING OUT SETTINGS ........................................................... 8-11
Downloaded From ManualsPrinter.com Manuals 
						

							8-2
KEY OPERATOR PROGRAMS
This chapter explains key operator programs that are related to the fax function. For key operator programs that are
related to general use of the machine, see the key operator programs manual.
KEY OPERATOR PROGRAM LIST
NOTE
You may not be able to use all of the programs in the key operator program list. Programs that you can use will
depend on what peripheral devices are installed on the machine.
Program name Page
OPERATION SETTINGS
Default display settings
8-4
The number of direct address/sender keys
displayed setting
8-4
Must input next address key at broadcast
setting
8-4
The number of file name/subject keys
displayed setting (when the network
scanner option is installed)
8-4
Initial resolution setting8-4
Scan complete sound setting8-5
Default exposure settings8-5
FAX SETTINGS
Fax default settings
Fax own number and name set
8-5
Auto wake up print8-5
Pause time setting8-6
Speaker volume settings8-6
Original print on transaction report8-6
Remote reception number setting (only
when extension phone is connected)
8-6
Transaction report print select setting8-6
Activity report print select setting8-6
ECM (This setting is only effective if the other
machine is a G3 machine that supports ECM)
8-7
Distinctive ring detection8-7
Disable of fax number direct entry8-7
Fax send settings
Auto reduction sending setting
8-7
Rotation sending setting8-7
Printing page number at receiver8-7
Call timer at memory sending8-8
Date/own number print position setting8-8
Quick on line sending8-8
Recall in case of line busy8-8
Recall in case of communication error8-8
Fax receive settings
Auto receive reduce setting
8-9
Number of calls in auto reception8-9
Duplex reception setting (only when the
duplex module option is installed)
8-9
Print style setting8-9
Set the telephone number for data
forwarding
8-9
Fax output tray setting8-9
Anti junk fax setting8-10
Fax polling security
Polling security setting
8-10
Passcode number setting8-10
Downloaded From ManualsPrinter.com Manuals 
						

							KEY OPERATOR PROGRAMS
8-3
8
USING THE KEY OPERATOR PROGRAMS
Follow these steps to configure the settings in the key operator programs.
1Press the [CUSTOM SETTINGS] key.
2Touch the [KEY OPERATOR PROGRAMS]
key.
3Use the numeric keys to enter the five-digit
key operator code number.
For the factory default
setting for the key
operator code number,
see page 2 of the key
operators guide.
4Touch the [IMAGE SEND SETTINGS] key.
5Touch the [OPERATION SETTINGS] key or
the [FAX SETTINGS] key to display the key
operator programs.
6Select the desired program and configure
the setting.
Page 8-2 shows the programs that can be selected.
The settings for each of the programs are explained
on the following pages.
7Press the [CA] key to exit the program.
QSupplementary explanation of key operation for key operator programs
A The name of the program category or particular item to be set will appear on the touch key. The displayed item
is selected by touching the key.
B Check mark boxes are touch keys that show the status of selections. A box with a check mark means the
function is on (enabled) and an unchecked box means the function is off (disabled). The on/off status
changes each time the box is touched.
C If the settings continue on the following screen(s), touch the   and   keys to move back and forth through
the screens. To return to the category selection screen, touch the [OK] key.
D The currently set numerical value is displayed.
E Numerical values can be set by touching the   and   keys.
KEY OPERATOR PROGRAMS
SENDER CONTROL
LIST PRINT
FAX DATA
RECEIVE/FORWADEFAULT
SETTINGS
KEY OPERATOR CODE
COPY SETTINGS
DOC. FILING 
SETTING
CONTROL
DEVICE CONTROL
IMAGE SEND
SETTINGS
CONTROL
E SEND SETTINGS
OPERATION SETTINGS
FAX SETTINGS
I-FAX SETTINGS
15(115)
A
KEY OPERATOR PROGRAMS
OPERATION SETTINGS
1/2
INITIAL RESOLUTION SETTING
THE NUMBER OF FILE NAME/
SUBJECT KEYS DISPLAYED SETTINGMUST INPUT NEXT ADDRESS
KEY AT BROADCAST SETTING
OK
DEFAULT DISPLAY SETTINGSTHE NUMBER OF DIRECT ADDRESS/ 
SENDER KEYS DISPLAYED SETTING
B
C
DE
6
6
These keys and indicator are
available on setting screens that
require the entry of numerical values.
Downloaded From ManualsPrinter.com Manuals 
						

							KEY OPERATOR PROGRAMS
8-4
KEY OPERATOR PROGRAMS
The key operator programs for the fax function of the machine are explained here.
For key operator programs that are related to the copy function and general use of the machine, see the key
operators guide. For programs related to the printer and network scanner functions, see the corresponding manuals.
OPERATION SETTINGS
ODefault display settings
O
The number of direct address/sender keys displayed setting
OMust input next address key at broadcast setting
OThe number of file name/subject keys displayed setting
(when the network scanner option is installed)
OInitial resolution setting
OScan complete sound setting
ODefault exposure settings
Default display settings
You can select the initial display that appears when you
press the [IMAGE SEND] key to change to fax mode or when
you press the [CA] key in fax mode. Normally the initial
display is set to the condition settings screen (page 1-4).
O[ADDRESS BOOK] (ABC)
O[ADDRESS BOOK] (Group)
O[FAX]
O[E-MAIL/FTP] (when the network scanner option
is installed)
O[INTERNET-FAX] (when the network scanner
option is installed)
When an address book (ABC or Group) is selected,
the selected index of that address book screen (page
1-5) is set as the initial screen.
When [SWITCH AUTOMATICALLY TO COPY MODE
SCREEN] is selected, the display will automatically
switch to the copy mode screen if no action is taken in
the fax / image send mode screen for 20 seconds.
The number of direct address/sender
keys displayed setting
The number of one-touch keys displayed in each
address book screen can be changed from 6 (the
normal setting) to 8 or 12.
Touch 6, 8, or 12 to select the desired number.
(When the network scanner option is installed, the
selections are 6 and 9.)
Must input next address key at
broadcast setting
You can select whether the [NEXT ADDRESS] key must
be pressed before entering the next destination when
performing a broadcast transmission (page 3-2). Normally
the machine is set so that touching the [NEXT ADDRESS]
key can be omitted except when the numeric keys are used
to enter one full fax number after another full fax number.
Example: Normal setting (factory setting)
If the box is checked, it will no longer be possible to
omit the [NEXT ADDRESS] key as shown in the
above example. Even if the next destination to be
entered is a one-touch key, the [NEXT ADDRESS]
key must be touched before the one-touch key can
be entered. If an operator attempts to enter the
next destination without touching the [NEXT
ADDRESS] key, an alarm will sound.
The number of file name/subject keys
displayed setting (when the network
scanner option is installed)
This program is used to select the number of file
name / subject keys that are displayed in the
screen. The number of keys can be set to 3 or 6.
Touch 3 or 6 to select the desired number.
Initial resolution setting
This program is used to set the initial resolution in
fax mode. Touch the [FAX] key and then change
the setting from STANDARD to FINE, SUPER
FINE, or ULTRA FINE. HALF TONE can also
be selected. STANDARD is normally selected for
the initial resolution setting.
If you wish to select HALF TONE for the selected
resolution setting, touch the [HALF TONE] key to
highlight it.
Select [APPLY THE RESOLUTION SET WHEN
STORED] to use the resolution setting of a stored
fax image when resending the image.
NOTE
Settings established with the key operator programs can be verified by printing them out (page 8-11).
NOTE
For the key name that appears in each one-touch
key, a maximum of 18 characters can appear when
the number of one-touch keys displayed is set to 6 or
8. A maximum of 10 characters can appear when the
number of one-touch keys displayed is set to 9 or 12.
XXXX NEXT ADDRESS One-touch NEXT ADDRESS One-touch
Dial
Can be omitted Can be omitted
XXXXNEXT ADDRESSXXXX
Dial Dial
Cannot be omitted.
Downloaded From ManualsPrinter.com Manuals 
						

							KEY OPERATOR PROGRAMS
8-5
8
Scan complete sound setting
You can select whether or not a beep sound is
made after an original is scanned on the scanner
unit.
Normally a beep sound is made.
You can select High or Low for the volume of
the beep.
Default exposure settings
This program is used to set the default exposure
level for scanning originals in fax / image send
mode, and for scan save in document filing mode*.
This program is initially set to AUTO. If changed
to MANUAL, the exposure level can be adjusted
to five levels. Level 1 is the lightest level and level
5 is the darkest level.
* Can only be used on the AR-M351N/AR-M451N.
The AR-M351U/AR-M451U models do not have this
function.
FAX SETTINGS
QFax default settings
The default fax settings can be changed as necessary
to meet your faxing needs.
The Fax default settings are as follows:
OFax own number and name set
OAuto wake up print
OPause time setting
OSpeaker volume settings
OOriginal print on transaction report
ORemote reception number setting (only when
extension phone is connected)
OTransaction report print select setting
OActivity report print select setting
OECM (This setting is only effective if the other
machine is a G3 machine that supports ECM)
ODistinctive ring detection
ODisable of fax number direct entry
Fax own number and name set
Use this setting to enter the fax number of the
machine and the name of the user. The entered
name and number are printed at the top of each fax
page you send. The number is also used as a
passcode when performing polling reception (see
USING THE POLLING FUNCTION on page
3-14).
1Touch the [NAME] key and enter the name.
The name entry screen appears.
Up to 20 characters can be entered for the name.
For information on entering characters, see
chapter 7 of the Operation manual (for general
information and copier operation).
2Touch the [FAX No.] key and enter the fax
number.
Enter up to 20 digits for the number using the
numeric keys.
To enter a +, press the   key.
To enter a hyphen, touch the [PAUSE] key. To
enter a space, touch the [SPACE] key.
If you make a mistake, press the [C] key and
re-enter the correct digit.
3Touch the [OK] key.
You will return to the OWN NUMBER AND NAME
SET screen. The number you entered appears.
Make sure it is correct.
Auto wake up print
Use this setting to select how the machine
responds if a fax is received when the power switch
is turned off (the fax power switch is turned on).
Auto wake up print is normally turned on, which
means that the machine automatically activates
and prints the received fax. If you turn off this
setting, received faxes will not be printed until the
power switch is turned on.
NOTE
If a hyphen is entered, it will be changed to a space
at the time of transmission.
Downloaded From ManualsPrinter.com Manuals 
						

							KEY OPERATOR PROGRAMS
8-6
Pause time setting
This setting is used to select the duration of pauses
that are inserted in destination fax numbers.
Normally the setting is 2 seconds, which means
that each time the [PAUSE] key is touched when
dialing or storing a fax number, a pause of 2
seconds is inserted.
The pause time can be set to any number of
seconds from 1 to 15.
Speaker volume settings
This program is used to adjust the volume of the
five following sounds that are emitted from the
speaker: 1.speaker, 2. ringer volume, 3. line
monitor, 4. fax receive signal, 5. Fax
communication error signal.
To change the volume, touch the desired volume
key. Factory default setting varies with
destinations.
Original print on transaction report
This program is used to have part of the first page
of the fax printed on the transaction report . This
program is used in conjunction with the transaction
report print select setting (at right), and is not
effective when printing of the transaction report is
disabled. 
This program is normally configured so that part of
the fax is printed on the transaction report when a
transmission is not successful.
Remote reception number setting
(only when extension phone is connected)
When a call is received (not made) on an extension
phone connected to the machine, fax reception can
be activated by entering a one-digit number and
pressing   twice on the phones keypad. This
number is called the remote reception number, and
you can set it to any number from 0 to 9. The
number is normally set to 5.
Transaction report print select setting
This program is used to select the condition for
printing a transaction report. The condition is set
separately for normal transmission, broadcast
transmission, reception, and confidential reception.
Touch the   key to display the next two settings. Select the
print conditions for receptions and confidential receptions
The normal settings are indicated by shading   above.
Activity report print select setting
This program is used to have the activity report stored in
the machines memory printed out at regular intervals.
You can choose to have the report automatically printed each
time the number of stored transactions exceeds 99*, or have the
report printed at a specified time every day (only once per day).
The report is normally set to not print out. Select AUTO
PRINT AT MEMORY FULL to have the report automatically
printed when the number of stored transactions (the
combined total of transmissions and receptions) exceeds 99*.
To have the report automatically printed at a
specified time, check the PRINT DAILY AT
DESIGNATED TIME box and then select the time
with the HOUR and MINUTE keys that appear.
Touch the HOUR and MINUTE keys and then set the
hour by touching the   and   keys. Set the minute in
the same way. When finished, touch the [OK] key.
*AR-M351N/AR-M451N only. On the AR-M351U/
 AR-M451U, 50 transactions are retained.
KEY OPERATOR PROGRAMSSPEAKER VOLUME SETTINGS
SPEAKER
RINGER VOLUME
1/2
LINE MONITOR
OK
Vo l u m e : H i g h Volume:Low Volume:MediumOff
NOTES
●
If you only select the PRINT DAILY AT DESIGNATED
TIME setting and the number of recorded transactions
exceeds 99* before the specified time, each new
transaction will delete the oldest transaction (the oldest
transaction will not be printed).
●The activity report can also be printed out on demand
(see PRINTING OUT SETTINGS on page 8-11).
SINGLE SENDING BROADCASTING
PRINT OUT ALL REPORT
PRINT OUT ERROR REPORT ONLY
NO PRINTED REPORT
PRINT OUT ALL REPORT
PRINT OUT ERROR REPORT ONLY
NO PRINTED REPORT
RECEIVINGCONFIDENTIAL RECEPTION
PRINT OUT ALL REPORT
PRINT OUT ERROR REPORT ONLY
NO PRINTED REPORT
PRINT OUT NOTICE PAGE
NOT PRINT OUT NOTICE PAGE
KEY OPERATOR PROGRAMSACTIVITY REPORT PRINT SELECT SETTING
AUTO PRINT AT MEMORY FULL
PRINT DAILY AT DESIGNATED TIME
OK
HOURMINUTE1301
Downloaded From ManualsPrinter.com Manuals 
						

							KEY OPERATOR PROGRAMS
8-7
8
ECM
(This setting is only effective if the other machine
is a G3 machine that supports ECM)
Line conditions can sometimes distort a
transmitted fax image. When ECM (Error
Correction Mode) is turned on, pages that are
distorted are automatically re-transmitted. This
setting is initially turned on. If turned off, distorted
images will be transmitted without being corrected.
Distinctive ring detection
This program can only be activated in Canada,
Australia, and New Zealand.
If multiple telephone numbers have been assigned
to your telephone line, the number called can be
identified by its ringing pattern. By using one
number for voice calls and another number for
faxes, you can tell which type of call you are
receiving by the ringing pattern. You can set your
machine to automatically receive faxes when your
fax number is called by setting the pattern that
corresponds to your fax number. (Note that in
Canada, six selections are available.) Normally
OFF is selected.
Disable of fax number direct entry
When the fax function is enabled, this program is
used to prohibit dialing of a destination fax number
by direct entry with the numeric keys. To prohibit
dialing by direct entry with the numeric keys, touch
the checkbox to select it. When this is done, faxes
can only be sent to destinations that have been
stored, and thus this program can be used to
restrict fax destinations and prevent accidental
transmission to an incorrect number. The following
operations are also prohibited:
OStoring one-touch dial numbers
ODirect entry of fax numbers when storing a group
ODirect entry of fax numbers of relay destinations in
a relay broadcast memory box
QFax send settings
The fax transmission settings allow you to adjust
certain parameters for sending faxes to better suit
your needs.
The fax send settings are as follows:
OAuto reduction sending setting
ORotation sending setting
OPrinting page number at receiver
OCall timer at memory sending
ODate/own number print position setting
OQuick on line sending
ORecall in case of line busy
ORecall in case of communication error
Auto reduction sending setting
This setting lets you select whether to have a
transmitted document reduced to match the size of
the other machines printing paper. Auto reduction
is normally turned on. If the setting is turned off,
documents are sent in their original size. Because
the size is not adjusted to match the size of the
printing paper, part of the received document may
be cut off.
Rotation sending setting
When transmitting a document, this setting allows
you to rotate a vertically oriented A4 (8-1/2x11)
document to a horizontal orientation (A4R
(8-1/2x11R)), rotate a B5R (5-1/2x8-1/2R)
document to B5 (5-1/2x8-1/2), or rotate a A5R
document to A5. The setting is normally turned on,
and documents are rotated counterclockwise.
(A4R (8-1/2x11R) documents are not rotated.)
Rotation settings can be separately established for
different document sizes. To turn off a rotation
setting, touch the checkbox of the appropriate
setting to remove the checkmark.
Printing page number at receiver
This setting lets you select whether page numbers
are printed at the top of fax pages by the receiving
machine. The normal setting is to have page
numbers printed.
NOTE
If the other machine supports Super G3, ECM will
function regardless of the setting.
KEY OPERATOR PROGRAMS
ROTATION SENDING SETTING
A4
B5
ORIGINAL
SETSENDING
DIRECTION
OK
B5R
A4R
B5 
A5RA5 
Downloaded From ManualsPrinter.com Manuals 
						

							KEY OPERATOR PROGRAMS
8-8
Call timer at memory sending
When sending a fax by automatic transmission
(See Storing transmission jobs (memory
transmission) on page 2-8.), this setting lets you
select the amount of time that the machine waits
before breaking the connection when the other
machine does not respond to your machines
calling tone. If the other machine does not respond
within this set time, your machine will automatically
break the connection. Time selections are 30
seconds, 45 seconds, and 60 seconds.  This setting
is normally set to 45 seconds.
Date/own number print position setting
This setting lets you select the position (inside or
outside the original image) of the senders name
and number that are printed at the top of each fax
page you send. Normally OUTSIDE THE
ORIGINAL IMAGE is selected. To have your name
and number printed inside the original image, select
INSIDE THE ORIGINAL IMAGE. For more detailed
information on the position of each setting, refer to
Position of senders information on page 3-11.
Quick on line sending
When this setting is turned on, the machine will call
the other machine and start transmitting the
document as soon as the first page is scanned.
Transmission therefore takes place at the same
time as any further pages are being scanned.
Normally this setting is turned on.
If you turn the setting off, transmission will not
begin until all pages of the document have been
scanned. Note that this setting does not apply to
manual transmission. (See Storing transmission
jobs (memory transmission) on page 2-8.)
Recall in case of line busy
This program is used to set the number of recall
attempts and the interval between recall attempts
when a transmission is not successful due to the
line being busy or other reason. 
Normally the machine is set to make 2 recall
attempts at intervals of 3 minutes.
The number of recall attempts and the interval
between attempts that can be set in each country
are shown in the following table.
Country Differentiation Table
If you do not wish recalling to take place, select
[TURN OFF RECALL].
Recall in case of communication error
When sending a document, this setting is used to
select whether your machine will re-attempt the call if
the transmission fails due to a line error.
Normally the machine is set to make 1 recall
attempts at intervals of 3 minutes*
1.
The number of recall attempts can be set to  only 1
time*
2, and the interval between attempts can be
set to any number of minutes from 1 to 15. If you do
not wish recalling to take place, select [TURN OFF
RECALL].
*1. Note that in United Kingdom, the interval
between attempts can be set to 1 minute.
*2. Note that in United Kingdom, the number of
recall attempts can be set to any number 1 to 5.
United
KingdomCanadaAustralia and
New Zealand
The number of
recall attempts1 to 10 1 to 14 1 to 9
The interval
between
attemptsany number of  minutes from 1 to 15
NOTE
Even if this setting is turned on, your machine will not
re-attempt the call when a document is sent by
manual transmission.
NOTE
Even if this setting is turned on, your machine will not
re-attempt the call when a document is sent by
manual transmission.
Downloaded From ManualsPrinter.com Manuals 
						

							KEY OPERATOR PROGRAMS
8-9
8
QFax receive settings
The fax reception settings allow you to adjust certain
parameters for receiving faxes to better suit your needs.
Settings that can be adjusted depend on the
peripheral devices installed.
The Fax receive settings are as follows:
OAuto receive reduce setting
ONumber of calls in auto reception
ODuplex reception setting (only when the duplex
module option is installed)
OPrint style setting
OSet the telephone number for data forwarding
OFax output tray setting
OAnti junk fax setting
Auto receive reduce setting
When you receive a fax that includes the senders
name and number, the received image is slightly
larger than the standard size*. This setting lets you
select whether or not the received image is
automatically reduced before printing to fit the
standard size. Normally automatic reduction is
turned on.
* Standard sizes are sizes such as A4 and B5
(8-1/2x11 and  8-1/2x5-1/2).
Number of calls in auto reception
This setting is used to select the number of rings on
which the machine automatically receives a call
and begins fax reception when the reception mode
is set to auto. (See RECEIVING A FAX on page
2-10.) Normally this setting is selected to 2.
The number of rings that can be set in each country
are shown in the following table.
Country Differentiation Table
Duplex reception setting
(only when the duplex module option is installed)
You can use this setting to select whether received
documents are printed on both sides of the paper.
Normally this setting is turned off. If turned on,
received documents will be printed on both sides of
the paper whenever the received document
consists of two or more pages of the same paper
size.
Print style setting
This setting determines the selection condition for
paper when printing received documents. Select
one of the three conditions below. AUTO SIZE
SELECT is normally selected.
OPRINT ACTUAL SIZE CUT OFF DISABLED
The received fax image is printed at its actual
size (without dividing it onto multiple sheets of
paper). If the same size of paper or larger paper
is not loaded, the fax will be received in memory
and will not be printed until a suitable size of
paper is loaded.
OPRINT ACTUAL SIZE CUT OFF ENABLED
Each received image is printed at actual size. If
necessary, the image is split onto multiple
sheets of paper.
OAUTO SIZE SELECT
Each received image is printed at actual size
when possible. When not possible, the image is
automatically reduced before printing.
Set the telephone number for data
forwarding
When a problem prevents the machine from printing
a received fax, the transfer function (page 3-18) can
be used to forward the received fax to another fax
machine. Use this setting to program the fax number
of the destination fax machine. Only one fax number
can be programmed (maximum of 64 digits).
If you wish to specify an F-code confidential memory
box in the destination machine, touch the [SUB
ADDRESS] key after entering the fax number to enter
a slash /, and then enter the sub-address. Enter a
passcode as well if needed. (See steps 9 to 12 of
STORING ONE-TOUCH DIAL KEYS on page 6-3
to 6-4.)
Fax output tray setting
This setting is used to select the output tray for
received faxes. The trays that can be selected will
vary depending on what peripheral devices have
been installed.
NOTE
If auto receive reduce is disabled, an image larger
than the standard size will be cut off. However, the
image is clearer because it is printed at the same
size as the original.
United 
KingdomCanadaAustralia and 
New Zealand
0 to 9 0 to 15 2 to 4
NOTE
If you select 0 for the number of rings, the machine
will immediately answer and begin fax reception
without ringing in auto reception mode.
However, do not select 0 when an extension phone
is connected to the machine.
When 0 is selected, the extension phone cannot be
used to make a call.
Downloaded From ManualsPrinter.com Manuals 
						

							KEY OPERATOR PROGRAMS
8-10
Anti junk fax setting
This program is used to enter fax numbers from
which you wish to block fax reception. Up to 50
(maximum of 30 on the AR-M351N/AR-M451N/
AR-M351U/AR-M451U) numbers can be entered.
This program is normally disabled.
To block reception from the entered fax numbers,
touch the [VALID] key.
1Touch the [ENTER] key.
The passcode entry screen appears.
2Enter the fax number with the numeric
keys.
Up to 20 digits can be entered.
When you have finished entering the number,
touch the [NEXT] key to store the number. A new
number entry screen will appear. Enter the next
number with the numeric keys.
3Touch the [OK] key.
1Touch the [DELETE] key.
The deletion screen will appear.
2Touch the number key that you wish to
delete.
A message will appear. Touch the [YES] key to
delete the number.
To cancel the deletion, touch the [NO] key.
QFax polling security
These settings are for using the Public Box for polling memory.
Note that they do not apply to F-code polling memory. (see
USING THE POLLING FUNCTION on page 3-14)
The Fax polling security are as follows:
OPolling security setting
OPasscode number setting
Polling security setting
When performing polling memory (See polling
security on page 3-16), this setting is used to select
whether any machine will be allowed to poll your
machine, or only machines that have been
programmed in your machine. Polling security setting
is normally turned on (a checkmark appears in the
box).
To allow any machine to poll your machine, touch the
box to remove the checkmark.
Passcode number setting
When the polling security setting is turned on, use
this setting to program (or delete) the fax numbers of
the machines that are allowed to poll your machine.
Programmed fax numbers are called passcodes. Up
to 10 fax numbers can be programmed.
1Touch the [ENTER] key.
The passcode entry screen appears.
2Touch a blank key (a key in which no
number appears).
Keys with numbers cannot be touched.
If numbers have been stored in all of the keys, a
message will appear and no further numbers can be
stored. First delete a number that is no longer
needed and then store the new number.
Entering anti junk fax numbers
Deleting an anti junk fax number
KEY OPERATOR PROGRAMS
ANTI JUNK FAX SETTING
ENTER
DEKETENOTE
If polling security setting is enabled, enter the
numbers of the fax machines to be allowed to poll
your machine in Passcode number setting below.
Programming passcode numbers
KEY OPERATOR PROGRAMSPASSCODE NUMBER SETTING
ENTERDELETE
OK
KEY OPERATOR PROGRAMSPASSCODE NUMBER SETTINGENTER
0666211221
0743535521
OKCANCEL
1/2
Downloaded From ManualsPrinter.com Manuals