Sharp Mx-b200 Service Manual

							Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
SERVICE MANUAL
CONTENTS
SHARP CORPORATION
CODE: 00ZMXB200/S1E
DIGITAL MULTIFUNCTIONAL 
SYSTEM
MODELMX-B200
MX-B200
[1] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
[2] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
[3] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES  . . . . . . . . . 4 - 1
[5] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
[6] COPY PROCESS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
[7] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
[8] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
[9] ADJUSTMENTS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1
[10] SIMULATION, TROUBLE CODES  . . . . . . . . . . . . . . . . . . . . . . . 10 - 1
[11] MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1
[12] USER PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1
[13] CHECKING THE TONER LEVEL  . . . . . . . . . . . . . . . . . . . . . . . . 13 - 1
[14] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 1
[15] CIRCUIT DIAGRAM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 - 1
[16] FLASH ROM VERSION UP PROCEDURE . . . . . . . . . . . . . . . . . 16 - 1 
						

							 CAUTION 
This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved
on the eye’s retina, there is the danger of spot damage to the retina.
The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of
servicing.
1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a
unit, not as individual parts.
2) Do not look into the machine with the mainswitch turned on after removing the developer unit, toner
cartridge, and drum cartridge.
3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected
when removing and installing the opti
cal system.
4) The middle frame contains the safety interlock switch.
Do not defeat the safety interlock by inserting wedges or other items into the switch slot.
LASER WAVE – LENGTH : 770 – 795nm
Pulse times : 10.24μsec
Out put power : 0.15mW 
± 0.01mW
CAUTION
INVISIBLE LASER RADIATION,
WHEN OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
VORSICHT
UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT.
NICHT DEM STRAHL AUSSETZEN.
VARO !
AVATTAESSA JA SUOJALUKITUS
OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ
KATSO SÄTEESEEN.
ADVARSEL
USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR
SIKKERHEDSBRYDERE ER UDE AF
FUNKTION. UNDGÅ UDSAETTELSE FOR
STRÅLNING.
VARNING !
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN. – STRÅLEN ÄR
FARLIG.
This product is a class 1 laser product that complies with 21CFR 1040 of the CDRH standard and 
IEC825. This means that this machine does not produce hazardous laser radiation. The use of controls, 
adjustments or performance of procedures other than those specified herein may result in hazardous 
radiation exposure. 
						

							The foregoing is applicable only to the 220V
model, 230V model and 240V model.
VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA
KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA
TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN
TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
VARNING - OM APPARATEN ANVÄNDS PÅ ANNAT
SÄTT ÄN I DENNA BRUKSANVISNING
SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS
FÖR OSYNLIG LASERSTRÅLNING, SOM
ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
At the production line, the output power
of the scanner unit is adjusted to 0.57
MILLI-WATT PLUS 20 PCTS and is
maintained constant by the operation of
the Automatic Power Control (APC).
Even if the APC circuit fails in operation
for some reason, the maximum output
power will only be 15 MILLI-WATT 0.1
MICRO-SEC. Giving and accessible
emission level of 42 MICRO-WATT
which is still-less than the limit of
CLASS-1 laser product.Caution
This product contains a low power laser
device. T o ensure continued safety do not
remove any cover or attempt to gain access
to the inside of the product.  Refer all
servicing to qualified personnel. 
						

							CONTENTS
[1] GENERAL
1. Major functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-1
[2] SPECIFICATIONS
1. Basic Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-1
2. Operation specifications. . . . . . . . . . . . . . . . . . . . . . . .  2-1
3. Copy performance . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-2
4. SPLC printer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-3
5. Scan function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-3
6. SPF (Option)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-3
[3] CONSUMABLE PARTS
1. Supply system table . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-1
A. Asia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-1
B. SMEF/Dealer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-1
C. SRH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-1
D. Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-1
2. Environmental  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-2
3. Production control number (lot No.) identification  . . . .  3-2
4. Toner cartridge replacement  . . . . . . . . . . . . . . . . . . . .  3-3
[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES
1. Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-1
2. Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-1
3. Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-2
4. Indicators on the operation panel. . . . . . . . . . . . . . . . .  4-3
5. Motors and solenoids . . . . . . . . . . . . . . . . . . . . . . . . . .  4-4
6. Sensors and switches  . . . . . . . . . . . . . . . . . . . . . . . . .  4-5
7. PWB unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-6
8. Cross sectional view  . . . . . . . . . . . . . . . . . . . . . . . . . .  4-7
[5] UNPACKING AND INSTALLATION
1. Copier installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-1
2. Cautions on handling . . . . . . . . . . . . . . . . . . . . . . . . . .  5-1
3. Checking packed components and accessories  . . . . .  5-1
4. Unpacking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-2
5. Removing protective packing materials . . . . . . . . . . . .  5-2
6. Developer unit installation  . . . . . . . . . . . . . . . . . . . . . .  5-2
7. Toner cartridge installation. . . . . . . . . . . . . . . . . . . . . .  5-3
8. Loading paper  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-3
9. Power to copier  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-4
10. Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-4
A. Hardware and software requirements . . . . . . . . . . .  5-4
B. Installing the software  . . . . . . . . . . . . . . . . . . . . . . .  5-5
C. Configuring the printer driver . . . . . . . . . . . . . . . . . .  5-7
D. Setting up Button Manager . . . . . . . . . . . . . . . . . . .  5-7
11. Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-8
A. USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-8
12. Moving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-9
13. Scanner moisture-proof kit . . . . . . . . . . . . . . . . . . . . . .  5-9
A. Components  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-9
B. Precautions at installation . . . . . . . . . . . . . . . . . . . .  5-9
C. Attachment method . . . . . . . . . . . . . . . . . . . . . . . . .  5-9
[6] COPY PROCESS
1. Functional diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-1
2. Outline of print process  . . . . . . . . . . . . . . . . . . . . . . . .  6-2
3. Actual print process . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-2[7] OPERATIONAL DESCRIPTIONS
1. Outline of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
2. Scanner section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
A. Scanner unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
B. Optical system  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
C. Drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
3. Laser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
A. Basic structure  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
B. Laser beam path . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
C. Composition  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
4. Fuser section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
A. General description. . . . . . . . . . . . . . . . . . . . . . . . . .7-4
5. Paper feed section and paper transport section . . . . . .7-4
A. Paper transport path and general operations . . . . . .7-4
6. SPF section (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . .7-7
A. Outline  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-7
B. Document transport path and basic composition  . . .7-7
C. Operational descriptions . . . . . . . . . . . . . . . . . . . . . .7-7
D. SPF open/close detection 
(book document detection) . . . . . . . . . . . . . . . . . . . .7-8
[8] DISASSEMBLY AND ASSEMBLY
1. High voltage section  . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
A. List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
B. Disassembly procedure  . . . . . . . . . . . . . . . . . . . . . .8-1
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . .8-1
D. Charger wire cleaning . . . . . . . . . . . . . . . . . . . . . . . .8-1
E. Charger wire replacement. . . . . . . . . . . . . . . . . . . . .8-2
2. Operation panel section  . . . . . . . . . . . . . . . . . . . . . . . .8-2
A. List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2
B. Disassembly procedure  . . . . . . . . . . . . . . . . . . . . . .8-2
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . .8-3
3. Optical section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3
A. List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3
B. Disassembly procedure  . . . . . . . . . . . . . . . . . . . . . .8-3
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . .8-4
4. Fusing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5
A. List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5
B. Disassembly procedure  . . . . . . . . . . . . . . . . . . . . . .8-5
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . . .8-7
5. Tray paper feed/transport section . . . . . . . . . . . . . . . . .8-8
A. List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-8
B. Disassembly procedure  . . . . . . . . . . . . . . . . . . . . . .8-8
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . .8-12
6. Manual paper feed section  . . . . . . . . . . . . . . . . . . . . . 8-12
A. List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-12
B. Disassembly procedure  . . . . . . . . . . . . . . . . . . . . . 8-12
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . .8-14
D. Pressure plate holder attachment . . . . . . . . . . . . . .8-14
7. Rear frame section  . . . . . . . . . . . . . . . . . . . . . . . . . . .8-14
A. List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-14
B. Disassembly procedure  . . . . . . . . . . . . . . . . . . . . . 8-14
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . .8-15
8. Power section  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-15
A. List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-15
B. Disassembly procedure  . . . . . . . . . . . . . . . . . . . . . 8-15
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . .8-15
9. Reverse roller section . . . . . . . . . . . . . . . . . . . . . . . . .8-15
A. List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-15
B. Disassembly procedure  . . . . . . . . . . . . . . . . . . . . . 8-15
C. Assembly procedure . . . . . . . . . . . . . . . . . . . . . . . .8-15 
						

							10. SPF section (Option) . . . . . . . . . . . . . . . . . . . . . . . . .  8-16
A. SPF motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8-16
B. Pick-up roller, paper feed roller . . . . . . . . . . . . . . .  8-17
C. Paper exit roller . . . . . . . . . . . . . . . . . . . . . . . . . . .  8-17
D. Set sensor, scan front sensor . . . . . . . . . . . . . . . .  8-18
E. Transport roller  . . . . . . . . . . . . . . . . . . . . . . . . . . .  8-18
[9] ADJUSTMENTS
1. Optical section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9-1
A. Copy magnification ratio adjustment . . . . . . . . . . . .  9-1
B. Image position adjustment  . . . . . . . . . . . . . . . . . . .  9-2
2. Copy density adjustment . . . . . . . . . . . . . . . . . . . . . . .  9-4
A. Copy density adjustment timing  . . . . . . . . . . . . . . .  9-4
B. Note for copy density adjustment  . . . . . . . . . . . . . .  9-4
C. Necessary tool for copy density adjustment  . . . . . .  9-4
D. Features of copy density adjustment . . . . . . . . . . . .  9-4
E. Copy density adjustment procedure  . . . . . . . . . . . .  9-4
3. High voltage adjustment  . . . . . . . . . . . . . . . . . . . . . . .  9-5
A. Main charger (Grid bias)  . . . . . . . . . . . . . . . . . . . . .  9-5
B. DV bias check . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9-5
4. SPF scan position automatic adjustment (Option) . . . .  9-5
5. SPF mode sub scanning direction magnification ratio 
adjustment (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . .  9-6
6. Automatic black level correction  . . . . . . . . . . . . . . . . .  9-6
[10] SIMULATION, TROUBLE CODES
1. Entering the simulation mode  . . . . . . . . . . . . . . . . . .  10-1
2. Key rule  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10-1
3. List of simulations  . . . . . . . . . . . . . . . . . . . . . . . . . . .  10-1
4. Descriptions of various simulations . . . . . . . . . . . . . .  10-2
5. Trouble codes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10-22
A. Trouble codes list  . . . . . . . . . . . . . . . . . . . . . . . .  10-22
B. Details of trouble codes . . . . . . . . . . . . . . . . . . . .  10-22
[11] MAINTENANCE
1. Maintenance table . . . . . . . . . . . . . . . . . . . . . . . . . . .  11-1
2. Maintenance display system  . . . . . . . . . . . . . . . . . . .  11-1
3. Remaining toner indication  . . . . . . . . . . . . . . . . . . . .  11-1
[12] USER PROGRAM
1. Setting the user programs . . . . . . . . . . . . . . . . . . . . .  12-1
[13] CHECKING THE TONER LEVEL . . . . . . . . . . . . . . . . . .  13-1
[14] ELECTRICAL SECTION
1. Block diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14-1
A. Overall block diagram  . . . . . . . . . . . . . . . . . . . . . .  14-1
2. Actual wiring diagram. . . . . . . . . . . . . . . . . . . . . . . . .  14-2
A. MCU PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14-2
B. SPF unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14-3
C. 2nd cassette unit . . . . . . . . . . . . . . . . . . . . . . . . . .  14-3
3. Signal name list . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14-4
[15] CIRCUIT DIAGRAM
1. MCU PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15-1
2. OPE PWB  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15-15
[16] FLASH ROM VERSION UP PROCEDURE
1. Preparation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16-1
2. Download procedure  . . . . . . . . . . . . . . . . . . . . . . . . .  16-1
3. Installation procedure. . . . . . . . . . . . . . . . . . . . . . . . .  16-2
A. USB joint maintenance program installation . . . . .  16-2
B. Installation procedure on Windows XP  . . . . . . . . .  16-2
C. Installation procedure on Windows 2000  . . . . . . .  16-3 
						

							MX-B200  GENERAL  1 - 1
[1] GENERAL
1. Major functions
Configurations
Descriptions of items
CPM:  Copy speed (Copies Per Minute)
PPM:  Print speed (Print Per Minute)
SB/MB:  SB = Manual feed single bypass, MB = Manual feed multi-bypass
2 Tray: Second cassette unit.
SPF: Original feed unit
R-SPF:  Duplex original feed unit
Color Scanner:Color scanner function
GDI printer:  GDI printer function with USB
SPLC printer: SPLC printer function
E-SORT:Electronic sort function
Duplex:  Auto duplex copy/print function
Shifter:Job separator function
FA X: FAX function.
Sharpdesk:Scanner utilities
IEEE1284:Interface port (parallel)
USB:Interface port (USB)
RJ45:Interface port (Network)
External NIC:Network expansion kit
Descriptions of table
: Standard provision
:  No function or no option available
Opt: Option Item
ModelCPM 
(A4)PPM 
(A4)SB/
MB2 
Tr a ySPFR-
SPFColor 
Scanner 
(push)GDI 
printerSPLC 
printerE-
SORTDuplex Shifter FAXSharp
deskIEEE
1284USBRJ
45External 
NIC
MX-
B20020CPM 20PPM  MB Opt Opt
(2.0
Hi-
speed)
MX-B200
MX-CS10 MX-SP10 
						

							MX-B200  SPECIFICATIONS  2 - 1
[2] SPECIFICATIONS
1. Basic Specifications
2. Operation specifications
Item
Type Desktop
Copy system Dry, electrostatic
Segment (class) Digital personal copier
Copier dimensions MX-B200 518mm (W) x 445mm (D) x 298mm (H) (20-1/2 (W) x 17-5/8 (D) x 11-3/4 (H))
Weight (Approximately) MX-B200 15.9kg (35.1 lbs.) Toner cartridge not included
Section, item Details
Paper feed 
sectionPaper feed 
system1 tray (250 sheet) + multi-bypass (50 sheet)
AB system Tray paper feed 
sectionPaper size A4, B5, A5 (Landscape)
Paper weight 56 - 80g/m
2 (15 - 21 lbs.)
Paper feed capacity 250 sheets
Kinds Standard paper, specified paper, recycled paper
Remark User adjustment of paper guide available
Multi-bypass paper 
feed sectionPaper size Max, feedable size: A4 / Min, feedable size: 89 x 140mm
Paper weight 56 - 128g/m
2 (15 - 34.5 lbs.)
Paper feed capacity 50 sheets (80g/m2)
Kinds Standard paper, specified paper, recycled paper, OHP, 
Label, (Single copy)
Remark User adjustment of paper guide available
Inch 
systemTray paper feed 
sectionPaper size 8-1/2 x 14, 8-1/2 x 13, 8-1/2 x 11, 8-1/2 x 5-1/2 
(Landscape)
Paper weight 15 - 21 lbs.
Paper feed capacity 250 sheets
Kinds Standard paper, specified paper, recycled paper
Remark User adjustment of paper guide available
Multi-bypass paper 
feed sectionPaper size Max, feedable size: 8-1/2 x 14 / Min, feedable size: 
3.87 x 5.83
Paper weight 15 - 34.5 lbs.
Paper feed capacity 50 sheets (80g/m
2)
Kinds Standard paper, specified paper, recycled paper, OHP, 
Label, Envelop (Single copy)
Remark User adjustment of paper guide available
Paper exit section Exit way Face down
Capacity of output tray 200 sheets
Originals Original set Center Registration (left edge)
Max. original size A4 (8-1/2 x 14)
Original kinds sheet, book
Original size detection None
Optical 
sectionScanning 
sectionScanning system 3 CCDs (RGB) sensor scanning by lighting white lamp
CCD sensor Resolution 600 dpi
Lighting lamp Type CCFL
Voltage 560Vrms
Power consumption 2.8W
Output data Output: R, G, B 1 or 8 bits/pixel / Input: A/D 16 bits (12 
bits actual)
Writing 
sectionWriting system Writing to OPC drum by the semiconductor laser
Laser unit Resolution 600 dpi
Image forming Photoconductor Type OPC (30ø)
Life 25k
Charger Charging system Saw-tooth charging with a grid, / (-) scorotron discharge
Transfer system (+) DC corotron system
Separation system (-) DC corotron system
Developing Developing system Dry, 2-component magnetic brush development system
Cleaning Cleaning system Counter blade system (Counter to rotation) 
						

							MX-B200  SPECIFICATIONS  2 - 2
3. Copy performance
*1:The first-copy time is measured after the power save indicator turns off following power on, using the document glass with the polygon rotat-
ing in the copy ready state and Selection of copy start state set to ON in the user programs (A4 (8-1/2 x 11), paper fed from paper tray).
The first-copy time may vary depending on machine operating conditions and ambient conditions such as temperature. Fusing section Fusing system Heat roller system
Upper heat roller Type Teflon roller
Lower heat roller Type Silicon rubber roller
Heater lamp Type Halogen lamp
Voltage 120V / 220 - 240V
Power consumption 800W
Electrical section Power source Voltage 120V / 220 - 240V
Frequency Common use for 50 and 60Hz
Power consumption Max. Less than 1000W
Average (during copying) 350Wh/H or less
Average (stand-by) 80Wh/H or less
Pre-heat mode 25Wh/H or less
Section, item Details
Copy ratio Document glass Variable:
25% to 400% in 1% increments (total 376 steps)
Fixed:
50%, 70%, 86%, 100%, 141%, 200%
(50%, 64%, 78%, 100%, 129%, 200%)
SPF Variable:
50% to 200% in 1% increments (total 151 steps)
Fixed:
50%, 70%, 86%, 100%, 141%, 200%
(50%, 64%, 78%, 100%, 129%, 200%)
Manual steps (Text, Photo) 5 steps
Copy speed (CPM) First-copy time *1 
(Approximately)8.0 seconds (When user program 24 is set to OFF)
10.7 seconds
(paper: A4 (8-1/2 x 11), exposure mode: AUTO, copy ratio: 100%)
AB system
A4 (Landscape)Same size 20
AB system
B5 (Landscape)Same size 20
Inch system
8-1/2 x 11 (Landscape)Same size 20
Max. continuous copy quantity 99
Void Void area Leading edge 1 - 4mm
Trailing edge 4mm or less
Side edge void area 0.5mm or more (per side)
4.5mm or less (total of both sides)
Image loss Leading edge same size: 3.0mm or less (OC) / 4mm or less (SPF)
Enlarge: 1.5mm or less (OC) / 3mm or less (SPF)
Reduction (50%): 6.0mm or less (OC) / 8mm or less (SPF)
Warm-up time - - -Section, item Details 
						

							MX-B200  SPECIFICATIONS  2 - 3
4. SPLC printer
*1: Engine Resolution
*2: Running change
5. Scan function
*1: By running change
6. SPF (Option)
Print speed Max. 20ppm (Paper size: A4, excluding manual paper feed)
∗Varies depending on the PC performance.
First print time 8 sec. (without data transfer time)
Duplex No
ROPM Yes
Memory 32MB
Interface USB 2.0 (Hi Speed)
Emulation SPLC
MIB support No
Resolution 600dpi *1
Supported OS Windows 2000 Professional, Windows XP Home Edition/Professional, Windows Vista, Windows 7
WHQL support Yes *2
Application Status window
Type Flat Bed Color Scanner
Scanning system Original table/SPF
Light source 3 CCDs (RGB) sensor scanning by lighting white lamp (1 pcs of CCFL)
Resolution Optical: 600 x 600dpi
Setting range: 50 - 9600dpi (Preview resolution is fixed at 75dpi)
Originals Sheet type / Book type
Output data R, G, B 1 or 8 bits/pixel
Scan range OC / SPF : 8.5 (H) x 14.0 (V)
Original position: Left Center
Scan speed OC / SPF : Max. 2.88ms/line
Protocol TWAIN / WIA (XP, Vista, 7) / STI
Interface USB 2.0 (Hi speed support)
Scanner utility Button Manager / Sharpdesk / Composer
Scan key/lamp Yes
Duplex scan No
Supported OS Windows 2000 Professional, Windows XP Home Edition/Professional, Windows Vista, Windows 7
Void area No (User settable by PC)
WHQL supported Yes *1
Original capacity 50 sheets (56 - 90g/m
2) (15 - 23.9 lbs.) Stacking Height: less than 6.5mm or 1/4
Original size A4 to A5 / 8-1/2 x 14 to 5-1/2 x 8-1/2 (Landscape)
Original replacement speed A4 about 13 sheets (65%)
8-1/2 x 11 about 14 sheets (70%)
Original placement Face up
Original weight 56 - 90g/m
2 (15 - 23.9lbs.)
Mixed feeding (Paper size) No
Original which cannot Thermal papers, originals with punch holes for files, be used folded paper, transparent originals such as 
OHP films, stapled or clip used originals with cover up liquid used, Originals with tape sealed, originals with 
high level frictional coefficient such as photos or catalogs. 
						

							MX-B200  CONSUMABLE PARTS  3 - 1
[3] CONSUMABLE PARTS
1. Supply system table
A. Asia
B. SMEF/Dealer
C. SRH
D. Europe
No. Name Content Life Product name Package
1 Toner cartridge (Black) Toner cartridge x 1
(Black toner: Net 243 g)
IC-Chip: Yes Stirring function: Ye s8K
(A4 6% Document)MX-B20AT1 10
2 Developer (Black) Developer x 1
(Black developer: Net 170 g)25K MX-B20AV1 10
3 Drum OPC drum x 1
Drum fixing plate x 125K AR-152DR 10
No. Name Content Life Product name Package
1 Toner cartridge (Black) Toner cartridge x 1
(Black toner: Net 243 g)
IC-Chip: Yes Stirring function: Ye s8K
(A4 6% Document)MX-B20FT1 10
2 Developer (Black) Developer x 1
(Black developer: Net 170 g)25K MX-B20AV1 10
3 Drum OPC drum x 1
Drum fixing plate x 125K AR-152DR 10
No. Name Content Life Product name Package
1 Toner cartridge (Black) Toner cartridge x 1
(Black toner: Net 243 g)
IC-Chip: Yes Stirring function: Ye s8K
(A4 6% Document)MX-B20AT1 10
2 Developer (Black) Developer x 1
(Black developer: Net 170 g)25K MX-20AV1 10
3 Drum OPC drum x 1
Drum fixing plate x 125K AR-152DR-C 10
No. Name Content Life Product name Package
1 Toner cartridge (Black) Toner cartridge x 1
(Black toner: Net 243 g)
IC-Chip: Yes Stirring function: Ye s8K
(A4 6% Document)MX-20GT1 10
2 Developer (Black) Developer x 1
(Black developer: Net 170 g)25K MX-20GV1 10
3 Drum OPC drum x 1
Drum fixing plate x 125K AR-152DM 10