Sharp Mx 2310u Owners Manual

MX-3610N  SIMULATION  5 – 12
 3-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1) Select the item to be operation checked with the touch panel key.
2) Press [EXECUTE] key. The selected load performs the operation.
When [EXECUTE] key is pressed,  the operation is terminated.
Inner finisher (MX-FN17) Saddle stitch finisher (MX-FN10)
 3-10
Purpose
Adjustment
Function (Purpose)
Used to...

MX-3610N  SIMULATION  5 – 13
Saddle stitch finisher (MX-FN10)
E STAPLE 
BOTH Stapling position 
adjustment (center 
position of two 
positions binding) 68 - 132 100 When the staple off-center is 
shifted, perform the 
adjustment. Staple 
position 
(Stapler stop 
position) 
(F/R 
direction)When the adjustment value is 
increased, the staple position is 
shifted to the rear side.
When the adjustment value is 
decreased, the staple position is 
shifted to the front side. 0.155mm
F STAPLE  PITCH Stapling...

MX-3610N  SIMULATION  5 – 14
F STAPLE REAR R Stapling position 
adjustment (Rear, 
one position /R 
series) 45 - 75 50 When the stapling 
position on the R 
side is shifted with R 
series paper, the 
adjustment is 
executed. Stapling position 
(stapler stop 
position) 
(F/R direction)
When the adjustment value is 
increased, the distance 
between the stapling position 
and the paper edge becomes 
longer.
When the adjustment value is 
decreased, the distance 
between the stapling position 
and the paper...

MX-3610N  SIMULATION  5 – 15
 
4
 4-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the sen-
sors and detectors in the desk/large capac-
ity tray (LCC), and the control circuit of
those.
Section
Desk/Large capacity tray (LCC)
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and  the detectors which are active
are highlighted.
Desk
LCC
 4-3
Purpose
Operation test/check
Function (Purpose)
Used to check...

MX-3610N  SIMULATION  5 – 16
 5-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the heater
lamp and the control circuit.
Section
Fusing
Operation/Procedure
1) Select the item to be operation checked with the touch panel key.
2) Press [EXECUTE] key. The selected heater lamp operates ON/OFF.
When [EXECUTE] key is pressed,  the operation is terminated.
Heater lamp operation check method: 
Remove the front cabinet upper and the paper exit tray, and the
lighting status of each...

MX-3610N  SIMULATION  5 – 17
 6-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of each fan
motor and its control circuit.
Section
Others
Operation/Procedure
1) Select the item to be operation checked with the touch panel key.
2) Press [EXECUTE] key. The selected load performs the operation.
When [EXECUTE] key is pressed,  the operation is terminated.
Press [ALL] key to select all the fans collectively.
Load operation check method: 
The load operation is checked by the...

MX-3610N  SIMULATION  5 – 18
 7-6
Purpose
Setting
Function (Purpose)
Used to set the operating intermittent aging
cycle.
Section
Operation/Procedure
1) Enter the intermittent aging operation cycle (unit: sec) with 10- key.
2) Press [OK] key. The time entered in procedure 1) is set.
* The interval time that can be set is 1 to 900 (sec).
The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.
 7-8
Purpose
Operation display
Function...

MX-3610N  SIMULATION  5 – 19
 8-2
Purpose
Operation test/check/adjustment
Function (Purpose)
Used to check and adjust the operation of
the main charger grid voltage in each
printer mode and the control circuit. 
* When the middle speed is adjusted, the
low speed are also adjusted simulta-
neously.
Section
Process (Charging)
Operation/Procedure
1) Select a speed with [MIDDLE] and [LOW] keys on the touch panel.
2) Select a target item to be adjusted with scroll keys.
3) Enter the adjustment value with...

MX-3610N  SIMULATION  5 – 20
Item/DisplayContentSetting 
range 18cpm/20cpm/
23cpm machine 26cpm/31cpm 
machine 36cpm machine
Default  value Actual 
output  value Default 
value Actual 
output  value Default 
value Actual 
output  value
A TC1 LOW SPEED CL  K Primary 
transfer 
bias 
adjustment 
valueColor K Low speed 51 - 255 80 6
A806 A806 A
B TC1 MIDDLE SPEED  CL K Middle speed 51 - 255 95 8
A 109 10 A11711 A
C TC1 LOW SPEED CL  C C Low speed 51 - 255 80 6
A806 A806 A
D TC1 MIDDLE SPEED  CL C...

MX-3610N  SIMULATION  5 – 21
 
9
 9-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the sen-
sors and detectors in the paper reverse
section (duplex section) and its control cir-
cuit.
Section
Duplex
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and  the detectors which are active
are highlighted.
 9-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the load in
the...