Sharp Mx 2310u Owners Manual

							MX-3610N  SIMULATION  5 – 12
 3-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1) Select the item to be operation checked with the touch panel key.
2) Press [EXECUTE] key. The selected load performs the operation.
When [EXECUTE] key is pressed,  the operation is terminated.
Inner finisher (MX-FN17) Saddle stitch finisher (MX-FN10)
 3-10
Purpose
Adjustment
Function (Purpose)
Used to adjust the finisher.
Section
Finisher
Operation/Procedure
1) Select an adjustment target item with scroll key on the touch panel.
2) Enter the set value with 10-key.
3) Press [OK] key. (The set value is saved.)
Inner finisher (MX-FN17)
Display Content
FCF Cooling fan
FDRLM Paper exit roller lift motor
FPAM_F Paper alignment motor F
FPAM_R Paper alignment motor R
FPAS Paper alignment solenoid
FPDM Paper exit motor
FPGS Paper gate solenoid
FPLDS Paper height detector solenoid
FPM Punch motor
FPS Paddle solenoid
FPSM Punch shift motor
FPTM Paper transport motor
FSM Staple motor
FSSM Stapler shift motor
FTLM Tray lift motor
Display Content
FDRLM Paper exit roller lift motor
FGM Gripper motor
FPAM_F Paper alignment motor F
FPAM_R Paper alignment motor R
FPHS1 Paper holding solenoid 1
FPHS2 Paper holding solenoid 2
FPM Punch motor
FPSM Punch shift motor
FPTM1 Paper transport motor 1
FPTM2 Paper transport motor 2
FSDM Saddle motor
FSDSM Saddle staple motor
FSM Staple motor
FSPAM Saddle paper alignment motor
FSPM Saddle positioning motor
FSPTM Saddle paper transport motor
FSSM Stapler shift motor
FTLM Tray lift motor
PDCF Paper pass cooling fan
PDPGS Paper pass paper gate solenoid
PDPTM Paper pass paper transport motor
Item/Display Content Setting 
range Default 
value Purpose (Case where the 
adjustment is required) Change when the adjustment value is 
increased or decreased Change 
when the 
adjustment  value is 
changed by 1
A FRONT  ADJUST Alignment position 
adjustment 
(F side alignment 
plate stop position) 
(Paper alignment 
adjustment) 2 - 18 10 This adjustment is used to 
adjust the paper alignment 
width when the paper 
alignment is improper.
Alignment is determined by 
the combination of the both 
adjustment values of FRONT 
ADJUST and REAR ADJUST. F side paper 
alignment 
stop position 
(F/R 
direction)
When the adjustment value is 
increased, the alignment plate stop 
position is shifted to the R side.
When the adjustment value is 
decreased, the alignment plate stop 
position is shifted to the F side. 0.3665mm
B REAR  ADJUST Alignment position 
adjustment 
(R side alignment 
plate stop position) 
(Paper alignment 
adjustment) 2 - 18 10 When changing the 
adjustment values of FRONT 
ADJUST and REAR ADJUST 
from the default values, be 
sure to change them by the 
same variation. R side paper 
alignment 
stop position 
(F/R 
direction)
When the adjustment value is 
increased, the alignment plate stop 
position is shifted to the F side.
When the adjustment value is 
decreased, the alignment plate stop 
position is shifted to the R side. 0.3665mm
C STAPLE  REAR Stapling position 
adjustment (one 
position at the 
rear) 68 - 132 100 When the staple position on 
the R side is shifted, perform 
the adjustment. Staple 
position 
(Stapler stop 
position) 
(F/R 
direction)When the adjustment value is 
increased, the staple position is 
shifted to the rear side.
When the adjustment value is 
decreased, the staple position is 
shifted to the front side. 0.155mm
D STAPLE  FRONT Stapling position 
adjustment (one 
position in front) 68 - 132 100 When the staple position on 
the F side is shifted, perform 
the adjustment. Staple 
position 
(Stapler stop 
position) 
(F/R 
direction)When the adjustment value is 
increased, the staple position is 
shifted to the rear side.
When the adjustment value is 
decreased, the staple position is 
shifted to the front side. 0.155mm 
						

							MX-3610N  SIMULATION  5 – 13
Saddle stitch finisher (MX-FN10)
E STAPLE 
BOTH Stapling position 
adjustment (center 
position of two 
positions binding) 68 - 132 100 When the staple off-center is 
shifted, perform the 
adjustment. Staple 
position 
(Stapler stop 
position) 
(F/R 
direction)When the adjustment value is 
increased, the staple position is 
shifted to the rear side.
When the adjustment value is 
decreased, the staple position is 
shifted to the front side. 0.155mm
F STAPLE  PITCH Stapling position 
adjustment (staple 
pitch of two 
positions binding) 68 - 132 100 When it is required to change 
the staple interval, perform 
the adjustment. Staple 
position 
(Stapler stop 
position) 
(F/R 
direction)When the adjustment value is 
increased, the staple interval is 
increased.
When the adjustment value is 
decreased, the staple interval is 
decreased. 0.155mm
G PUNCH  CENTER Punch center 
positioning sensor 37 - 63 50 When the punch off-center is 
shifted, perform the 
adjustment. Punch 
position 
(F/R 
direction)When the adjustment value is 
decreased, the punch position is 
shifted to the front side.
When the adjustment value is 
increased, the punch position is 
shifted to the rear side. 0.1441mm
H PUNCH  HOLE Punch hole 
adjustment (paper 
transport direction) 42  -  58 50 When the punch hole position 
is shifted in the transport 
direction, perform the 
adjustment. Punch 
position 
(Paper 
transport 
direction)When the adjustment value is 
increased, the punch position is 
shifted to the paper lead edge side.
When the adjustment value is 
decreased, the punch position is 
shifted to the paper rear edge side. 0.2584mm
Item/Display Content
Setting 
range Default 
value Purpose (Case where the 
adjustment is required) Change when the adjustment value is 
increased or decreased Change 
when the 
adjustment  value is 
changed by 1
Item/Display Content Setting 
range Default 
value Purpose 
(Case where the 
adjustment is  required) Change when the adjustment value is increased 
or decreased Change when 
the adjustment 
value is 
changed by 1
ASADDLE  POSITION Saddle stitch 
position 
adjustment 25 - 75 50 The adjustment is 
executed when the 
saddle staple 
position is shifted. Saddle paper lead 
edge striking plate 
stop position (Up-
down direction)When the adjustment value is 
increased, the stapling 
position is shifted to the lead 
edge of transported paper.
When the adjustment value is 
decreased, the stapling 
position is shifted to the rear 
edge of transported paper. 0.2mm
B FOLDING  POSITION Saddle folding 
position 
adjustment 25 - 75 50 The adjustment is 
executed when the 
saddle folding 
position is shifted. Saddle paper lead 
edge striking plate 
stop position (Up-
down direction)When the adjustment value is 
increased, the folding position 
is shifted to the lead edge of 
transported paper.
When the adjustment value is 
decreased, the folding 
position is shifted to the rear 
edge of transported paper. 0.2mm
C FRONT  ADJUST Alignment position 
adjustment (front) 35 - 65 50 When the paper 
alignment capability 
in the stacker 
section is improper, 
the paper alignment 
width is adjusted. F side paper 
alignment plate stop 
position 
(F/R direction)
When the adjustment value is 
increased, the alignment 
position is shifted to the 
center.
When the adjustment value is 
decreased, the alignment 
position is shifted to the 
outside. 0.2mm
D REAR  ADJUST Alignment position 
adjustment (Rear) 35 - 65 50
R side paper 
alignment plate stop 
position 
(F/R direction) When the adjustment value is 
increased, the alignment 
position is shifted to the 
center.
When the adjustment value is 
decreased, the alignment 
position is shifted to the 
outside. 0.2mm
E STAPLE REAR Stapling position  adjustment (Rear, 
one position)25 - 75 50 When the stapling 
position on the R 
side is shifted, the 
adjustment is 
executed. Stapling position 
(stapler stop 
position) 
(F/R direction)
When the adjustment value is 
increased, the distance 
between the stapling position 
and the paper edge becomes 
longer.
When the adjustment value is 
decreased, the distance 
between the stapling position 
and the paper edge becomes 
shorter. 0.2mm 
						

							MX-3610N  SIMULATION  5 – 14
F STAPLE REAR R Stapling position 
adjustment (Rear, 
one position /R 
series) 45 - 75 50 When the stapling 
position on the R 
side is shifted with R 
series paper, the 
adjustment is 
executed. Stapling position 
(stapler stop 
position) 
(F/R direction)
When the adjustment value is 
increased, the distance 
between the stapling position 
and the paper edge becomes 
longer.
When the adjustment value is 
decreased, the distance 
between the stapling position 
and the paper edge becomes 
shorter. 0.2mm
G STAPLE  FRONT Stapling position 
adjustment (one 
position in front) 25 - 75 50 When the stapling 
position on the F 
side is shifted, the 
adjustment is 
executed. Stapling position 
(stapler stop 
position) 
(F/R direction)
When the adjustment value is 
decreased, the distance 
between the stapling position 
and the paper edge becomes 
shorter.
When the adjustment value is 
increased, the distance 
between the stapling position 
and the paper edge becomes 
longer. 0.2mm
H STAPLE  FRONT R Stapling position 
adjustment (Front, 
one position / R 
series) 25 - 55 50 When the stapling 
position on the F 
side is shifted with R 
series paper, the 
adjustment is 
executed. Stapling position 
(stapler stop 
position) 
(F/R direction)
When the adjustment value is 
decreased, the distance 
between the stapling position 
and the paper edge becomes 
shorter.
When the adjustment value is 
increased, the distance 
between the stapling position 
and the paper edge becomes 
longer. 0.2mm
I STAPLE BOTH Stapling position  adjustment (Two 
positions, center)45 - 55 50 When the staple off-
center is shifted, the 
adjustment is 
executed. Stapling position 
(stapler stop 
position) 
(F/R direction)When the adjustment value is 
increased, the stapling 
position is shifted to the front.
When the adjustment value is 
decreased, the stapling 
position is shifted to the rear. 0.2mm
J STAPLE  PITCH Stapling position 
adjustment (Two 
positions, pitch) 35 - 62 50 When the stapling 
interval is to be 
changed, the 
adjustment is 
executed. Stapling position 
(stapler stop 
position) 
(F/R direction)
When the adjustment value is 
increased, the pitch of two 
points is widened.
When the adjustment value is 
decreased, the pitch of two 
points is narrowed. 0.2mm
K PUNCH  CENTER Punch center 
adjustment 35 - 65 50 When the punch off-
center is shifted, the 
adjustment is 
executed. Punching position 
(F/R direction)
When the adjustment value is 
increased, the hole position is 
shifted to the front.
When the adjustment value is 
decreased, the hole position 
is shifted to the rear. 0.2mm
L PUNCH HOLE Punch hole  position 
adjustment30 - 60 50 When the punch 
hole position is 
shifted in the 
transport direction, 
the adjustment is 
executed. Punch position 
(paper transport 
direction)
When the adjustment value is 
increased, the punch hole 
position is shifted to the rear 
edge of paper.
When the adjustment value is 
decreased, the punch hole 
position is shifted to the lead 
edge of paper. 0.2mm
MSADDLE_ ADJUST_POS Saddle alignment 
position 
adjustment 35 - 65 50 When the paper 
alignment capability 
in the saddle 
section is improper, 
the paper alignment 
width is adjusted. Saddle paper 
alignment plate stop 
position 
(F/R direction)
When the adjustment value is 
increased, the alignment plate 
position is shifted to the 
center.
When the adjustment value is 
decreased, the alignment 
plate position is shifted to the 
outside. 0.2mm
N GRIPPER_ POS Gripper exit 
position 
adjustment 35 - 65 50 When the gripper 
discharge position is 
shifted, the 
adjustment is 
executed. (When a 
JAM or trouble 
occurs, the 
adjustment is 
executed.) Gripper discharge 
position (Gripper 
stop position) 
(F/R direction)
When the adjustment value is 
increased, the gripper 
discharge position is shifted to 
the front.
When the adjustment value is 
decreased, the gripper 
discharge position is shifted to 
the rear. 0.2mm
Item/Display Content
Setting 
range Default 
value Purpose 
(Case where the  adj
 ustment is 
required) Change when the adjustment value is increased 
or decreased Change when 
the adjustment  value is 
changed by 1 
						

							MX-3610N  SIMULATION  5 – 15
 
4
 4-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the sen-
sors and detectors in the desk/large capac-
ity tray (LCC), and the control circuit of
those.
Section
Desk/Large capacity tray (LCC)
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and  the detectors which are active
are highlighted.
Desk
LCC
 4-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the loads
in the desk/large capacity tray (LCC), and
the control circuit of those.
Section
Desk/Large capacity tray (LCC)
Operation/Procedure
1) Select the load item that is required to operation check with the touch panel key.
2) Press [EXECUTE] key. The selected load performs the operation.
When [EXECUTE] key is pressed,  the operation is terminated. Desk
LCC
 4-5
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the paper
feed desk paper transport clutch (DTRC)
and the LCC paper transport clutch (LTRC).
Section
Desk/Large capacity tray (LCC)
Operation/Procedure
Check the ON operation
Press the button of the code name for checking the ON operation.
Checking is started. When the operation is normal, the button on
the display is highlighted. When it is abnormal, the button is not
highlighted.
Check the OFF operation
Press the highlighted button which is ON.
When the operation is normal, the highlighted button on the display
returns to the normal display. When it is abnormal, the highlighted
display is maintained.
 
5
 5-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the display,
LCD in the operation panel, and control cir-
cuit.
Section
Operation panel
Operation/Procedure
The LCD is changed as shown below.
The contrast changes every 2sec  from the current level to MAX 
MIN   the current level. During this period, each LED is lighted.
The LCD display contrast change and the LED lighting status are
checked.
Display Content
D1MDC Desk 1 installation detection connector
D1PPD Desk 1 paper transport detector
D1ULD Desk 1 upper limit detector
D1PED Desk 1 paper empty detector
D1PQD Desk 1 remaining paper quantity detector
D1PRED1 Desk 1 paper rear edge detector 1
D1PRED2 Desk 1 paper rear edge detector 2
D1PRED3 Desk 1 paper rear edge detector 3
D1PRED4 Desk 1 paper rear edge detector 4
D2MDC Desk 2 installation detection connector
D2PPD Desk 2 paper transport detector
D2ULD Desk 2 upper limit detector
D2PED Desk 2 paper empty detector
D2PQD Desk 2 remaining paper quantity detector
D2PRED1 Desk 2 paper rear edge detector 1
D2PRED2 Desk 2 paper rear edge detector 2
D2PRED3 Desk 2 paper rear edge detector 3
D2PRED4 Desk 2 paper rear edge detector 4
Display Content
LPFD LCC transport detector
LUD LCC tray upper limit detector
LDD LCC tray lower limit detector
LPED LCC tray paper empty detector
LCLD LCC tray open/close detector
LDSW LCC upper open/close detection switch
LRE LCC lift motor encoder sensor
L24VM LCC24V power monitor
LLSW LCC upper limit switch
LCCD LCC main unit connection detector
Display Content
D1LM Tray 1 lift-up motor
D1PFC Tray 1 paper feed clutch
D2LM Tray 2 lift-up motor
D2PFC Tray 2 paper feed clutch
DPFM Desk transport motor
DPTRC Desk paper transport clutch
Display Content
LPFM LCC transport motor
LLM LCC lift motor
LPFC LCC paper feed clutch
LPFS LCC paper feed solenoid
LTRC LCC transport clutch
Button Content
DTRC Desk transport clutch
LTRC LCC transport clutch 
						

							MX-3610N  SIMULATION  5 – 16
 5-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the heater
lamp and the control circuit.
Section
Fusing
Operation/Procedure
1) Select the item to be operation checked with the touch panel key.
2) Press [EXECUTE] key. The selected heater lamp operates ON/OFF.
When [EXECUTE] key is pressed,  the operation is terminated.
Heater lamp operation check method: 
Remove the front cabinet upper and the paper exit tray, and the
lighting status of each heater lamp can be checked through the
clearance between the fusing pressure release drive gear and the
frame fusing section.
 5-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the scanner
lamp and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1) Select the item to be operation checked with the touch panel key.
2) Press [EXECUTE] key. The scanner lamp lights up for 10 sec.
When [EXECUTE] key is pressed,  the operation is terminated.
 5-4
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the dis-
charge lamp and the control circuit.
Section
Process
Operation/Procedure
1) Select a target of the operation check with the touch panel key. When [ALL] key is pressed, all the items are selected.
2) Press [EXECUTE] key. The selected discharge lamp is lighted for 30 sec.
When [EXECUTE] key is pressed,  the operation is terminated.
 
6
 6-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the load in
the paper transport system (clutches and
solenoids) and the control circuits.
Section
Paper transport/Paper exit section
Operation/Procedure
1) Select the item to be operation checked with the touch panel key.
2) Press [EXECUTE] key. The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
Load operation check method: 
The load operation is checked by the operation sound. However,
there are some loads which cannot  be checked with the operation
sound.
*1: If Normal rotation and Reverse rotation of a same load are displayed as different items, when the both are selected at the
same time, Normal rotation is performed. In addition, a
change in the rotating direction  is accepted only when the
operation is stopped.
*2: Displayed but not installed in some models.
HL_LM Heater lamp (B) (Back surface)
HL_UM Main heater lamp (F) (Front surface)
HL_US Sub heater lamp (F) (Front surface)
DL_K Discharge lamp K
DL_C Discharge lamp C
DL_M Discharge lamp M
DL_Y Discharge lamp Y
Section Item/Display Content
Transport/
process ADUC1 ADU transport clutch 1
PFM
Transport motor
RRM Registration motor
POMF (*1) Paper exit motor (normal rotation)
POMR (*1) Paper exit motor (reverse rotation)
FUM Fusing motor
CPFM Paper feed motor
OSM Offset motor
CPFC1 Tray vertical transport clutch 1
CPFC2 Tray vertical transport clutch 2
TRC_DSK Desk clutch
TRC_LCC (*2) LCC clutch
TRC_FIN Finisher clutch
HPFC Transport roller clutch
PFC Vertical transport clutch
RRC Registration roller clutch
Paper feed CLUM1 Paper tray lift motor (Paper feed tray 1) CPUC1 Paper feed clutch (Paper feed tray 1)
CLUM2 Paper tray lift motor (Paper feed tray 2)
CPUC2 Paper feed clutch (Paper feed tray 2)
CPUS1 Paper feed pickup solenoid  (Paper feed tray 1) (Not used)
MPFS Paper feed solenoid (Manual paper feed) 
						

							MX-3610N  SIMULATION  5 – 17
 6-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of each fan
motor and its control circuit.
Section
Others
Operation/Procedure
1) Select the item to be operation checked with the touch panel key.
2) Press [EXECUTE] key. The selected load performs the operation.
When [EXECUTE] key is pressed,  the operation is terminated.
Press [ALL] key to select all the fans collectively.
Load operation check method: 
The load operation is checked by the operation sound. However,
there are some loads which cannot be checked with the operation
sound.
18/20/23/26/31cpm machine
36cpm machine
 6-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the trans-
port unit and the control circuit.
Section
Process (Transport)
Operation/Procedure
1) Select the operation mode with the mode select button.
2) When [EXECUTE] key is presse d, the operation of the mode
selected in 1) is performed.
 6-6
Purpose
Operation test/check
Function (Purpose)
Used to perform fusing pressure release
and applying, and to check the operations
of the control circuits.
Section
Fusing
Operation/Procedure
1) Press [FUSER] key to highlight it.
2) Press [EXECUTE] key, and fusing pressure applying and fus- ing pressure release are repeated.
During this period, the status of the fusing roller pressure is dis-
played.
 6-90
Purpose
Setting
Function (Purpose)
Used to reset the machine to the factory
setting. (The scanner is set to the lock
enable position)
Section
Scanner
Operation/Procedure
1) Press [EXECUTE] key. The scanner is shifted to the lock enable position and stopped.
 
7
 7-1
Purpose
Setting
Function (Purpose)
Used to set the operating conditions of
aging.
Section
Others
Operation/Procedure
1) Select an item to be set with the touch panel key.
2) Press [EXECUTE] key. The machine is rebooted in the aging mode.
The aging operation condition set  by this mode is maintained here-
after unless the power is turned off or the setting is changed.
Display Content
PROFM2 Process fan 2
POFM Paper exit cooling fan  (Drives POFM1 and POFM2 at the same time.)
FUFM Fusing cooling fan
PROFM1 Process fan 1
PSFM Power cooling fan
Display Content
POFM Paper exit cooling fan motor  (Drives POFM1 and POFM2 at the same time.)
PSFM Power cooling fan motor
PROFM1 Process fan motor 1
PROFM2 Process fan motor 2
FUFM Fusing fan motor
LSUFM LSU cooling fan motor
Mode select button Content
TC1 Primary transfer (normal rotation)
TC1_R Primary transfer (reverse rotation)
TC2 Secondary transfer
Mode 
select 
button Mode 
display Content
NOTE
TC1 BLACK Monochrome  mode positionBlack mode position 
 Color 
mode position   Black mode 
position   Drum separation 
position   (Black mode 
position) 
(Repeated in this sequence.) 
COLOR Color mode 
position
FREE Non-transport  position
TC1_R BLACK Monochrome  mode positionBlack mode position 
 Drum 
separation position   Color 
mode position   (Black 
mode position) (Repeated in 
this sequence.)
FREE Non-transport 
position
COLOR Color mode  position
TC2 PRINT Print position Print position - Transfer  position - Non-transfer 
position (Repeated in this 
sequence)
FREE Non-transport 
position
PRINT Fusing pressure  applying Fusing pressure applying 
 Fusing 
pressure release   (Fusing pressure 
applying) The operation is repeated.
FREE Fusing pressure 
release
AGING Aging operation setup
INTERVAL Intermittent operation setting
MISFEED DISABLE JAM detection ignoring setting
FUSING DISABLE Fusing unit ignoring setting
WARMUP DISABLE Warming up ignoring setting
DV CHECK DISABLE Developing unit ignoring setting
SHADING DISABLE Shading correction operation omitting setting
CCD GAIN FREE CCD gain adjustment omitting setting Mode 
select 
button Mode 
display Content
NOTE 
						

							MX-3610N  SIMULATION  5 – 18
 7-6
Purpose
Setting
Function (Purpose)
Used to set the operating intermittent aging
cycle.
Section
Operation/Procedure
1) Enter the intermittent aging operation cycle (unit: sec) with 10- key.
2) Press [OK] key. The time entered in procedure 1) is set.
* The interval time that can be set is 1 to 900 (sec).
The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.
 7-8
Purpose
Operation display
Function (Purpose)
Used to display the warm-up time.
Section
Operation/Procedure
Press [EXECUTE] key.
Counting of the warm-up time is started and the time required for
warm-up is displayed
* Interruption of counting by pres sing [EXECUTE] key is inhibited.
 7-9
Purpose
Operation test/check
Function (Purpose)
Color setting in the color copy test mode
(Used to check the copy operation and the
image quality for each color).
Section
Operation/Procedure
1) Select the copy color with the touch panel key.  (Two or more colors can be selected.)
The key of the selected color is highlighted.
2) Press [EXECUTE] key. Copying is performed with the selected color.
When [CLOSE] key is pressed, the  display goes into the copy oper-
ation menu in the simulation mode.
 7-12
Purpose
Operation test/check
Function (Purpose)
The document reading number of sheets
setting (for aging operation)
Section
RSPF
Operation/Procedure
1) Set document reading quantity with 10-key.  (Setting range:0 - 255)
2) Press [OK] key. The set value is saved.
The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.
 
8
 8-1
Purpose
Operation test/check/adjustment
Function (Purpose)
Used to check and adjust the operations of
the developing voltage in each print mode
and the control circuit. 
* When the middle speed is adjusted, the
low speed are also adjusted simulta-
neously.
Section
Process (Developing)
Operation/Procedure
1) Select a speed with [MIDDLE] and [LOW] keys on the touch panel.
2) Select a target item to be adjusted with scroll keys.
3) Enter the setting value with 10-key. (The value specified on the label of the high voltage PWB must be entered.)
* When the     key is pressed, the setting value of eachitem can be changed with 1up (1down) collectively.
4) Press [EXECUTE] key. The set value is saved and the voltage entered with step 3) is
output for 30 sec.
When [EXECUTE] key is pressed, the output is terminated.
K Setup/cancel of black
C Setup/cancel of cyan
M Setup/cancel of magenta
Y Setup/cancel of yellow
Item/Display (Mode) Content Adjustment 
range Actual 
voltage
MIDDLE A MIDDLE  SPEED 
DVB_KDeveloping 
bias voltage 
(Middle 
speed mode) K 0 - 600 –450V
5V
B MIDDLE  SPEED 
DVB_C Developing 
bias voltage 
(Middle 
speed mode) C 0 - 600 –450V
5V
C MIDDLE  SPEED 
DVB_M Developing 
bias voltage 
(Middle 
speed mode) M 0 - 600 –450V
5V
D MIDDLE  SPEED 
DVB_Y Developing 
bias voltage 
(Middle 
speed mode) Y 0 - 600 –450V
5V
LOW A LOW  SPEED 
DVB_KDeveloping 
bias voltage 
(Low speed 
mode) K 0 - 600 –450V
5V
BLOW  SPEED 
DVB_C Developing 
bias voltage 
(Low speed 
mode) C 0 - 600 –430V
5V
CLOW  SPEED 
DVB_M Developing 
bias voltage 
(Low speed 
mode) M 0 - 600 –430V
5V
DLOW  SPEED 
DVB_Y Developing 
bias voltage 
(Low speed 
mode) Y 0 - 600 –430V
5V 
						

							MX-3610N  SIMULATION  5 – 19
 8-2
Purpose
Operation test/check/adjustment
Function (Purpose)
Used to check and adjust the operation of
the main charger grid voltage in each
printer mode and the control circuit. 
* When the middle speed is adjusted, the
low speed are also adjusted simulta-
neously.
Section
Process (Charging)
Operation/Procedure
1) Select a speed with [MIDDLE] and [LOW] keys on the touch panel.
2) Select a target item to be adjusted with scroll keys.
3) Enter the adjustment value with 10-key. (The value specified on the label of the high voltage PWB must be entered.)
* When the     key is pressed, the setting value of eachitem can be changed with 1up (1down) collectively.
4) Press [EXECUTE] key. The set value is saved and the voltage entered with step 3) is
output for 30 sec.
When [EXECUTE] key is press ed, the output is terminated.
 8-6
Purpose
Operation test/check/adjustment
Function (Purpose)
Used to check and adjust the operation ofthe transport voltage and the control circuit.
Section
Process (Transport)
Operation/Procedure
1) Select a target item to be adjusted with scroll keys.
2) Enter the set value with 10-key.  Enter the default value spec ified on the following list.
3) Press [EXECUTE] key. The set value is saved and the voltage corresponding to the
set value is output for 30 sec. 
When [EXECUTE] key is press ed, the output is terminated.
Item/Display (Mode) ContentAdjustment 
range Actual voltage
18cpm/
20cpm/ 23cpm 
machine 26cpm/
31cpm 
machine 36cpm 
machine
MIDDLE A MIDDLE SPEED GB_K Main charger grid voltage (Middle speed mode) K 150 - 850 –615V 5V –620V 5V –625V 5V
B MIDDLE SPEED GB_C Main charger grid voltage (Middle speed mode) C 150 - 850 –615V 5V –620V 5V –625V 5V
C MIDDLE SPEED GB_M Main charger grid voltage (Middle speed mode) M 150 - 850 –615V 5V –620V 5V –625V 5V
D MIDDLE SPEED GB_Y Main charger grid voltage (Middle speed mode) Y 150 - 850 –615V 5V –620V 5V –625V 5V
LOW A LOW SPEED GB_K Main charger grid voltage (Low speed mode) K 150 - 850 –610V 5V –610V 5V –610V 5V
B LOW SPEED GB_C Main charger grid voltage (Low speed mode) C 150 - 850 –590V 5V –590V 5V –590V 5V
C LOW SPEED GB_M Main charger grid voltage (Low speed mode) M 150 - 850 –590V 5V –590V 5V –590V 5V
D LOW SPEED GB_Y Main charger grid voltage (Low speed mode) Y 150 - 850 –590V 5V –590V 5V –590V 5V 
						

							MX-3610N  SIMULATION  5 – 20
Item/DisplayContentSetting 
range 18cpm/20cpm/
23cpm machine 26cpm/31cpm 
machine 36cpm machine
Default  value Actual 
output  value Default 
value Actual 
output  value Default 
value Actual 
output  value
A TC1 LOW SPEED CL  K Primary 
transfer 
bias 
adjustment 
valueColor K Low speed 51 - 255 80 6
A806 A806 A
B TC1 MIDDLE SPEED  CL K Middle speed 51 - 255 95 8
A 109 10 A11711 A
C TC1 LOW SPEED CL  C C Low speed 51 - 255 80 6
A806 A806 A
D TC1 MIDDLE SPEED  CL C Middle speed 51 - 255 95 8
A 109 10 A11711 A
E TC1 LOW SPEED CL  M M Low speed 51 - 255 80 6
A806 A806 A
F TC1 MIDDLE SPEED  CL M Middle speed 51 - 255 95 8
A 109 10 A11711 A
G TC1 LOW SPEED CL  Y Y Low speed 51 - 255 80 6
A806 A806 A
H TC1 MIDDLE SPEED  CL Y Middle speed 51 - 255 95 8
A 109 10 A11711 A
I TC1 LOW SPEED BW  K Black/White K Low speed 51 - 255 80 6
A806 A8
 06A
J TC1 MIDDLE SPEED  BW K Middle speed 51 - 255 95 8
A 109 10 A11711 A
K TC2 PLAIN CL SPX Secondary  transfer 
bias 
adjustment 
valueColor Standard 
paperFront surface 51 - 255 96 –35
A 103 –40 A 110 –45 A
L TC2 PLAIN CL DPX Back surface 51 - 255 76 –20A90–30 A 96 –35 A
M TC2 PLAIN BW SPX Black/WhiteFront surface 51 - 255 96 –35 A 103 –40 A 110 –45 A
N TC2 PLAIN BW DPX Back surface 51 - 255 76 –20A90–30 A 96 –35 A
O TC2 HEAVY1 CL SPX Color Heavy 
paper 1Front surface 51 - 255 83 –25
A83–25 A 83 –25 A
P TC2 HEAVY1 CL DPX  Back surface 51 - 255 76 –20A76–20 A 76 –20 A
Q TC2 HEAVY1 BW SPX Black/WhiteFront surface 51 - 255 69 –15 A69–15 A 69 –15 A
R TC2 HEAVY1 BW DPX Back surface 51 - 255 69 –15A69–15 A 69 –15 A
S TC2 HEAVY2 CL  Color Heavy paper 2 51 - 255 83 –25 A83–25 A 83 –25 A
T TC2 HEAVY2 BW Black/White51 - 255 69 –15A69–15 A 69 –15 A
U TC2 OHP CL ColorOHP51 - 255 69 –15 A69–15 A 69 –15 A
V TC2 OHP BW  Black/White51 - 255 69 –15A69–15 A 69 –15 A
W

TC2 ENVELOPE CL ColorEnvelope 51 - 255 69 –15 A69–15 A 69 –15 A
X TC2 ENVELOPE BW Black/White51 - 255 69 –15A69–15 A 69 –15 A
Y TC2 THIN CL ColorThin paper 51 - 255 96 –35 A 103 –40 A 110 –45 A
Z TC2 THIN BW Black/White51 - 255 96 –35A 103 –40 A 110 –45 A
AA TC2 GLOSSY CL ColorGloss paper 51 - 255 83 –25 A83–25 A 83 –25 A
AB TC2 GLOSSY BW Black/White51 - 255 69 –15A69–15 A 69 –15 A
AC TC2 CLEANING Secondary  transfer 
cleaning 
bias 
adjustment 
valueCleaning process (negative pole) 51 - 255 59 –8
A59–8 A59–8 A
AD TC2 CLEAN LOW SPD Low speed print mode0 - 255 26 0V 26 0V 26 0V
AE TC2 CLEAN MIDDLE  SPD Middle speed print mode 0 - 255 26 0V 26 0V 26 0V
AF TC2 CLEAN  CLEANING Cleaning bias (positive pole) 0 - 255 102 500V 102 500V 102 500V
AG PTC LOW SPEED CL PTC  current 
adjustment 
valueColor
Low speed 51 - 255 73 –200 A 73 –200A 73 –200 A
AH PTC MIDDLE SPEED  CL Middle speed 51 - 255 73 –200
A 73 –200 A 73 –200 A
AI PTC LOW SPEED BW Black/White Low speed 51 - 255 73 –200 A 73 –200A 73 –200 A
AJ PTC MIDDLE SPEED  BW Middle speed 51 - 255 73 –200
A 73 –200 A 73 –200 A
AK CASE VOLT LOW CL PTC  voltage 
adjustment 
valueColor
Low speed 0 - 255 0 0V 0 0V 0 0V
AL CASE VOLT MID CL Middle speed 0 - 255 0 0V 0 0V 0 0V
AM CASE VOLT LOW BW Black/White Low speed 0 - 255 0 0V 0 0V 0 0V
AN CASE VOLT MID BW Middle speed 0 - 255 0 0V 0 0V 0 0V 
						

							MX-3610N  SIMULATION  5 – 21
 
9
 9-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the sen-
sors and detectors in the paper reverse
section (duplex section) and its control cir-
cuit.
Section
Duplex
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and  the detectors which are active
are highlighted.
 9-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the load in
the paper reverse section (duplex section)
and its control circuit.
Section
Duplex
Operation/Procedure
1) Select the item to be operation checked with the touch panel key.
2) Press [EXECUTE] key. The selected load performs the operation.
When [EXECUTE] key is pressed,  the operation is terminated.
18cpm/20cpm/23cpm/26cpm/31cpm machine
*1: Displayed, but not installed in some models.
36cpm machine
*: Not used, but the button is displayed.
 
10
 10-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the toner
supply mechanism (toner motor) and the
related circuit.
Section
Process (Developing)
Operation/Procedure
1) Select a target of the operation check with the touch panel key. When [ALL] key is pressed, all the items are selected.
2) Press [EXECUTE] key. The selected load operation is performed for 10 sec.
When [EXECUTE] key is pressed,  the operation is terminated. This simulation must be executed without installing the toner car-
tridges.
If this simulation is executed with the toner cartridges installed,
toner will be forcibly supplied to
 the developing unit, resulting in
overtoner.
If this simulation is erroneously ex ecuted with the toner cartridges
installed, overtoner state may be deleted by making a few black
background copy in the single color copy mode of the target color.
 
13
 13--
Purpose
Cancel (Trouble etc.)
Function (Purpose)
Used to cancel the self-diag U1 trouble.
Section
Operation/Procedure
1) Press [EXECUTE] key.
2) Press [YES] key to execute cancellation of the trouble.
 
14
 14--
Purpose
Cancel (Trouble etc.)
Function (Purpose)
Used to cancel the self-diag H3, H4, H5troubles.
Section
Operation/Procedure
1) Press [EXECUTE] key.
2) Press [YES] key to execute cancellation of the trouble.
 
15
 15--
Purpose
Clear/Cancel (Trouble etc.)
Function (Purpose)
Used to cancel the self-diag U6 trouble.
Section
LCC
Operation/Procedure
1) Press [EXECUTE] key.
2) Press [YES] key to execute cancellation of the trouble.
APPD1 ADU paper transport detector 1
APPD2 ADU paper transport detector 2
DSW_ADU ADU paper guide open/close detector
Display Content
ADUM ADU motor
ADUC1 ADU transport clutch 1 *
1
Display Content
ADUC1 ADU transport clutch 1 (*)
ADUM ADU motor
ADUGS ADU gate solenoid
TNM_K Toner motor K
TNM_C Toner motor C
TNM_M Toner motor M
TNM_Y Toner motor Y