Sharp Mx 2310u Owners Manual

							MX-3610N  SIMULATION  5 – 2
18cpm/20cpm/23cpm/31cpm(G) machine
YES
NO
NOYES
YES
YES
NO
NO
NO
YES
NO
YES YES
NO
NO
YES
YES
NOStandby for entry of SIM
sub code
Enter SIM sub code with the 10-key.
Press the START key.
The display is made according
to the selected mode and the item. START (Copy mode)
Press the Program key.
Press the asterisk (*) key.
Press the clear key.
Press the Program key. Standby for entry of SIM code.
Enter the main code of SIM with the 10-key.
The main code of SIM is displayed.
Press the START key.
Is there a sub code ?
Select the mode and the item with the scroll key and the item key.
Operation check ?
Operating conditions check ?
Data clear ?
Adjustments
or setting (counter data
change) ?
Do you
want to change the content ?
Enter the new setting and adjustment values. Press the SYSTEM
SETTINGS key
Press the SYSTEMSETTINGS key
Press the EXECUTE key and OK key.
Operation is made according
to the selected mode and item.
Press the EXECUTE key
and OK key.
Press the EXECUTE key and OK key.
The display is made according tothe selected some and the item.
Press the EXECUTE key
and OK key.
Is it the same
simulation main code?
Do you want
to perform another simulation ?
Do you
want to end the simulation ?
The changed content is stored. The simulation mode
is canceled.
Press the clear all key.
Operation is made according
to the selected mode and the item. (Other modes)
The selected mode and
the item are cleared.

You have to exit
simulation mode
before entering into this mode for self printing type.In the power OFF/ON type simulation, OFF/ON message is
displayed by the SYSTEM
SETTINGS key.
If there is no item. 
						

							MX-3610N  SIMULATION  5 – 3
26cpm/36cpm/31cpm(A) machine
YES
NO
NOYES
YES
YES
NO
NO
NO
YES
NO
YES YES
NO
NO
YES
YES
NOStandby for entry of SIM
sub code
Enter SIM sub code with the 10-key.
Press the
COLOR/MONO key.
The display is made according
to the selected mode and the item. START (Copy mode)
Double-click the HOME key.
Touch the VER display section.
Press the sharp (#) key.
Press the asterisk (*) key.
Press the clear key.
Press the Program key. Standby for entry of SIM code.
Enter the main code of SIM with the 10-key.
The main code of SIM is displayed.
Press the
COLOR/MONO key.
Is there a sub code ?
Select the mode and the item with the scroll key and the item key.
Operation check ?
Operating conditions check ?
Data clear ?
Adjustments
or setting (counter data
change) ?
Do you
want to change the content ?
Enter the new setting and adjustment values. Press the BACK key
Press the BACK key
Press the EXECUTE keyand OK key.
Operation is made according
to the selected mode and item.
Press the EXECUTE key
and OK key.
Press the EXECUTE key and OK key.
The display is made according tothe selected some and the item.
Press the EXECUTE key
and OK key.
Is it the same
simulation main code?
Do you want
to perform another simulation ?
Do you
want to end the simulation ?
The changed content is stored. The simulation mode
is canceled.
Press the EXIT key.
Operation is made according
to the selected mode and the item. (Other modes)
The selected mode and
the item are cleared.

You have to exit
simulation mode
before entering into this mode for self printing type.In the power OFF/ON type simulation, OFF/ON message is
displayed by the SYSTEM
SETTINGS key.
If there is no item. 
						

							MX-3610N  SIMULATION  5 – 4
3. List of simulation codes
Main SubFunctions Section
1 1 Used to check the operation of the scanner (readi ng) unit and the control circuit.Scanner (reading)
2 Used to check the sensors in the scanner (reading)  section and the related circuits.Scanner (reading)
5 Used to check the operation of the scanner (readi ng) unit and the control circuit. Scanner (reading)
2 1 Used to check the operations of the automatic document feeder and the control circuit. RSPF
2 Used to check the operations of the sensors and the detectors in the automatic document feeder section  and the control circuits. RSPF
3 Used to check the operations of the loads in the automatic document feeder and the control circuit. RSPF
3 2 Used to check the operations of the sensors and the det ectors in the finisher and the control circuit. Finisher
3 Used to check the operation of the load in the finisher and the control circuit. Finisher
10 Used to adjust the finisher. Finisher
4 2 Used to check the operations of t he sensors and detectors in the desk/large capacity tray (LCC), and the 
control circuit of those. Desk/Large capacity tray (LCC)
3 Used to check the operations of the loads in the desk /large capacity tray (LCC), and the control circuit of 
those. Desk/Large capacity tray (LCC)
5 Used to check the operations of the paper feed desk paper transport clutch (DTRC) and the LCC paper  transport clutch (LTRC). Desk/Large capacity tray (LCC)
5 1 Used to check the operation of the display, LCD in the operation panel, and control circuit. Operation panel
2 Used to check the operation of the heater lamp and the control circuit. Fusing
3 Used to check the operation of the scanner  lamp and the control circuit. Scanner (reading)
4 Used to check the operation of the discharge lamp and the control circuit. Process
6 1 Used to check the operations of the load in the paper transport system (clutches and solenoids) and the  control circuits. Paper transport/Paper exit section
2 Used to check the operations of each fan motor and its control circuit. Others
3 Used to check the operations of the transport  unit and the control circuit. Process (Transport)
6 Used to perform fusing pressure release and applying, and to check the operations of the control  circuits. Fusing
90 Used to reset the machine to the factory setting. (The scanner is set to the lock enable position) Scanner
7 1 Used to set the operating conditions of aging. Others
6 Used to set the operati ng intermittent aging cycle.
8 Used to display the warm-up time.
9 Color setting in the color copy test mode (Used to check the copy operation and the image quality for  each color).
12 The document reading number of sheets setting (for aging operation) RSPF
8 1 Used to check and adjust the operations of the developing voltage in each print mode and the control  circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously. Process (Developing)
2 Used to check and adjust the operation of the main charger grid voltage in each printer mode and the  control circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously. Process (Charging)
6 Used to check and adjust the operation of the transport voltage and the control circuit. Process (Transport)
9 2 Used to check the operations of the sensors and dete ctors in the paper reverse section (duplex section) 
and its control circuit. Duplex
3 Used to check the operations of the load in the paper reverse section (duplex section) and its control  circuit. Duplex
10 1 Used to check the operations of the toner supply mechani sm (toner motor) and the related circuit. Process (Developing)
13 - Used to cancel the self-diag U1 trouble.
14 - Used to cancel the self-diag H3, H4, H5 troubles.
15 - Used to cancel the self-diag U6 trouble. LCC
16 - Used to cancel the self-diag U2 trouble. MFP PWB / PCU PWB / SCU PWB
17 - Used to cancel the self-diag PF trouble.
21 1 Used to set the maintenance cycle.
22 1 Used to check the print count value in each section and each operation mode.  (Used to check the maintenance timing.)
2 Used to check the total number of misfeed and troubles.  (When the number of total jam is considerably great, it is judged as necessary for repair.)
3 Used to check misfeed positions and the misfeed count of each position.  * Presumption of the faulty point by this data is possible.
4 Used to check the trouble (self diag) history.
5 Used to check the ROM version  of each unit (section). Firmware
6 Used to output the setting/adjustment data (simulation, FAX soft switch, counter), the firmware version,  and the counter list.
8 Used to check the number of operations (counter val ue) of the finisher, the RSPF, and the scan (reading) 
unit.
9 Used to check the number of use (print quantity) of each paper feed section. Paper feed, ADU, LCC
10 Used to check the system configuration (option, internal hardware).
11 Used to check the use frequency (send/receive)  of FAX. (Only when FAX is installed) FAX 
12 Used to check the RSPF misfeed positions and  the number of misfeed at each position. (When the 
number of misfeed is considerably great, it can be judged as necessary for repair.) RSPF
13 Used to check the operating time of the process section (OPC drum, DV unit, toner cartridge) and the  fusing unit Process
14 Used to display the use status of the toner cartridge. Process 
						

							MX-3610N  SIMULATION  5 – 5
22 18 Used to display the user data delete history.19 Used to check the values of the co unters related to the scan - image send.
40 Used to display the error code list and the contents.
90 Used to output the various set data lists.
23 2 Used to output the trouble history list of paper jam and misfeed.  (If the number of troubles of misfeed is considerably gr eat, the judgment is made that repair is required.)
80 Used to check the operation of paper feed and paper transport in the paper feed section and the paper  transport section. Used to output the list of the operat ion status of the sensor and the detectors in the 
paper feed section and the paper transport section. Paper feed, Paper transport
24 1 Used to clear the jam counter, and the trouble counter.  (After completion of maintenance, clear the counters.)
2 Used to clear the number of use (the number of prints) of each paper feed section.
3 Used to clear the finisher, RSPF, and the scan (reading) unit counter.
4 Used to clear the maintenance counter, the printer c ounters of the transport unit and the fusing unit. 
(After completion of maintenance, clear the counters.)
5 Used to clear the developer counter. (After replacement of developer, clear the counter.)
6 Used to clear the copy counter.
9 Used clear the printer mode print counter and the self print mode print counter.
10 Used to clear the FAX counter. (Only when FAX is installed)
15 Used to clear the counters related to the scan mode and the image send.
35 Used to clear the toner cartridge use status data.
25 1 Used to check the operations of the deve loping section. Process (Developing section)
2 Used to make the initial setting of toner density when repl acing developer. (Automatic adjustment) Image process (Photoconducto r/
Developing/Transfer/Cleaning)
4 Used to display the operation data of the toner supply quantity. (Not used in the market.) Process
5 Used to display the toner density correcti on data. (Not used in the market.) Process
26 1 Used to set Yes/No of installation of the right paper exit tray. Paper exit
2 Used to set the paper size of the large capacity  tray (LCC). (When the paper size is changed, this 
simulation must be executed to change the paper size in software.) Paper feed
3 Used to set the specifications of the auditor.  (Setting must be made according to the auditor use conditions.) Auditor
5 Used to set the count mode of the total counter and the maintenance counter. (A3/11x17 size)
6 Used to set the specifications (paper, fixed m agnification ratio, etc.) of the destination.
7 Used to set the machine ID. (26cpm/36cpm/31cpm(A) machine)
10 Used to set the trial mode of the network scanner.
18 Used to set Disable/Enable of the toner save mode operation. (For the Japan and the UK versions.)
30 Used to set the operation mode corresponding to the CE mark (Europe safety standards).  (For slow start to drive the fusing heater lamp)
32 Used to set the specifications of  the fusing cleaning operation. Fusing
35 Used to set the display mode of SIM 22-4 trouble history when a same trouble occurred repeatedly.  There are two display modes: display as one tr ouble and display as several series of troubles.
38 Used to set Continue/Stop of print when the maintenance life is reached.
41 Used to set Enable/Disable of the magnification ratio automatic select function (AMS) in the center  binding mode.
49 Used to set the print speed of postcards mode.
50 Used to set functions.
51 Used to set the specifications of  the serial port operation. (For PCI)
52 Used to set whether non-printed paper (insertion paper, cover paper) is counted up or not.
53 User auto color calibration (color balance adjustment) Inhibit/Allow setting.
65 Used to set the finisher alarm mode.
69 Used to set the operating conditions for toner near end.
71 Used to set the trial mode of the web brow sing function. (26cpm/36cpm/31cpm(A) machine)
73 Enlargement continuous shoot, A3 wide copy  mode image loss (shade delete quantity) adjustment
74 Used to set the OSA trial mode.
78 Used to set the password of the remote operation panel.
79 Used to set YES/NO of the pop-up display of user data delete result.
Main Sub
Functions Section 
						

							MX-3610N  SIMULATION  5 – 6
27 1 Used to set non-detection of communication error (U7-00) with RIC. (FSS function)2 Used to set the senders registration number and the HOST server telephone number. (FSS function)
4 Used to set the initial call and toner order auto send. (FSS function)
5 Used to set the machine tag No. (This function allows  the host computer to check the machine tag No.) 
(FSS function) Communication (RIC/MODEM)
6 Used to set of the manual service call. (FSS function)
7 Used to set of the enable, alert callout. (FSS function)
9 Used to set the paper transport time recording YES/NO threshold value and shading gain adjustment  retry number. (FSS function)
10 Used to clear the trouble prediction history information. (FSS function) 11 Used to check the serial communication retry number and the scanner gain adjustment retry number  history. (FSS function)
12 Used to check the high density, halftone process co ntrol and the automatic registration adjustment error 
history. (FSS Function)
13 Used to check the history of paper trans port time between sensors. (FSS function)
14 Used to set the FSS function connection test mode.
15 Used to display the FSS connection status.
16 Used to set the FSS alert send.
17 Used to set the FSS paper order alert.
18 Used to clear the FSS paper feed retry counter.
30 1 Used to check the operations of the sensors and  the detectors in other than the paper feed section and 
the control circuits.
2 Used to check the operations of the sensors and the  detectors in the paper feed section and the control 
circuits.
33 2 Used to delete the ID (IDM) information of Felica card. (23cpm/31cpm(G) machine only)
40 2 Manual paper feed tray paper width sensor adjustment. Paper feed
7 Used to set the adjustment value of the manual paper feed tray paper width sensor. Paper feed
41 1 Used to check the operations of the docu ment size sensor and the control circuit.
2 Used to adjust the document size sensor detection level.
3 Used to check the operations of the docu ment size sensor and the control circuit.
43 1 Used to set the fusing temperature in each mode. 4 Used to set the fusing temperature 2 in each mode. (Continued from SIM 43-1.)
20 Used to set the environmental correction under low temperature and low humidity (L/L) for the fusing  temperature setting (SIM 43-1) in each paper mode.
21 Used to set the environment correction under high temperature and high humidity (H/H) for the fusing  temperature setting (SIM 43-1) in each paper mode.
22 Used to set the environment correction under low temperature and low humidity (L/L) for the fusing  temperature setting (SIM 43-4) in each paper mode.
23 Used to set the environment correction under high temperature and high humidity (H/H) for the fusing  temperature setting (SIM 43-4) in each paper mode.
24 Used to set the correction of the temperature adjustment value of SIM 43-1 and 43-4.
31 Used to check the operation of the fusing web cleaning. (36cpm machine) Fusing
32 Used to set various items related to the forcible operation of web cleaning when job end.  (36cpm machine) Fusing
44 1 Used to set each correction operation function in the image forming (process) section. Image process (Photoconductor/
Developing/Transfer/Cleaning)
2 Used to adjust the sensitivity of the image density sensor (registration sensor). Process
4 Used to set the conditions of the high  density process control operation. Process
6 Used to execute the high density process control forcibly. Process
9 Used to display the result data of the high density process control operation. Image process (Photoconductor/
Developing/Transfer/Cleaning)
12 Used to display the operation data of the high de nsity process control and the image density sensor 
(registration sensor). Image process (Photoconductor/
Developing)
13 Used to perform the color image sensor (image registration sensor F) calibration.
14 Used to display the output level of the temperature  and humidity sensor.Process (OPC drum, development)/
Fusing/LSU
15 Used to set the OPC drum idle rotation. Process
21 Used to set the halftone process control target. Process
22 Used to display the toner patch density level in the halftone process control operation. Process
24 Used to display the correction target and the correction level in the halftone process control operation. Process
25 Used to set the calculating conditions of the correction value for the halftone process control. Process
26 Used to execute the halftone process control compulsory. Process
27 Used to clear the correction data of the halftone process control. Process
28 Used to set the process contro l execution conditions. Process
29 Used to set the operating conditions of  the process control during a job. Process
31 Used to adjust the OPC drum phase. (Manual adjustment) Process
37 Used to set the development bias correcti on level in the continuous printing operation.
43 Used to display the identification information of the developing unit. Developing system
61 Used to adjust the color image density sensor. (The adj ustment is made according to the input of SIM44-
13 to set the target value of the color sensor gain adjustment.)
62 Used to set the process contro l execution conditions. Process
Main Sub
Functions Section 
						

							MX-3610N  SIMULATION  5 – 7
46 1 Used to adjust the copy density in the copy mode.2 Used to adjust the copy density in the copy mode.
4 Used to adjust the density in the image send mode.
5 Used to adjust the density in the image send mode.
8 Used to adjust the image send mode color balance RGB.
9 Used to adjust the scan image density.
10 Used to adjust the copy color balance and the gamma (for each color copy mode).
16 Used to adjust the monochrome copy density and  the gamma (for each monochrome copy mode).
19 Used to set the operating conditions for the densit y scanning (exposure) of monochrome auto copy 
mode documents.
21 Copy color balance adjustment (Manual adjustment)
23 Used to set the density correction of copy high  density section (High density tone gap supported).
24 Copy color balance adjustment (Auto adjustment)
25 Used to adjust the copy color balance. (Single color copy mode)
26 Used to reset the single color mode color balance set value to the default.
27 Used to adjust the gamma/density of  copy images, texts, and line image edges.
30 Used to adjust the resolution in the sub scanning direction in the copy mode.
32 Used to adjust the document background density r eproducibility in the monochrome auto copy mode.
36 Used to adjust the colors in the 2-color copy mode.
37 Used to adjust the reproduction capability of monochrome mode color.
38 Used to adjust the black component amount in the color copy mode.
39 Used to adjust the sharpness of FAX send images.
40 Used to adjust the FAX send image density.  (Collective adjustment of all the modes)
41 Used to adjust the FAX send image density. (Normal)
42 Used to adjust the FAX send image density. (Fine)
43 Used to adjust the FAX send image density. (Super Fine)
44 Used to adjust the FAX send image density. (Ultra fine)
45 Used to adjust the FAX send image density. (600dpi).
46 Used to adjust the FAX send image density.  (RGB RIP) (26cpm/36cpm/31cpm(A) machine)
47 Used to set the compression rate of copy and scan images (JPEG).
51 Used to adjust the gamma for the copy mode heavy paper mode and the image process mode.
52 Used to set the gamma default for the copy mode heavy paper and the image process mode.  (After execution of either SIM46-54 or SIM46-51, the adjustment value is reset to the initial value.)
54 Used to perform the engine halftone automatic density adjustment (dither). 
55 Used to adjust the drop out color in the image send mode (monochrome manual text mode).  (26cpm/36cpm/31cpm(A) machine)
58 Used to set the copy mode pseudo resolution. (Smoothing process)
59 Used to perform the copy mode pseudo resolution image process adjustment.
60 Used to adjust the sharpness in the color auto copy mode.
61 Used to adjust the area separation recognition level.
62 Used to set the operating conditions of the ACS, the area separation, the background image process,  and the auto exposure mode.
63 Used to adjust the density in the copy low density section.
65 Used to set the color correction table.
66 Used to adjust the reproduction capability  of watermarks in the copy/printer mode. 
(26cpm/36cpm/31cpm(A) machine)
74 Copy color balance adjustment (Auto adjustment)/Printer color balance adjustment (Auto adjustment)
90 Used to set the process operation of high-compression PDF images.  (26cpm/36cpm/31cpm(A) machine)
91 Used to adjust the reproduction capability of  black text. (26cpm/36cpm/31cpm(A) machine)
48 1 Used to adjust the scan image magnification rati o (in the main scanning direction and the sub scanning 
direction).
5 Used to correction the scan image magnification ra tio (in the sub scanning direction).Scanner section
6 Used to adjust the rotation speed of each motor.
49 1 Used to perform the firmware update. 3 Used to update the operation manual in the HDD.
5 Used to perform the watermark update.
Main Sub
Functions Section 
						

							MX-3610N  SIMULATION  5 – 8
50 1 Copy image position, image loss adjustment2 Used to adjust the copy image position and the image loss. (This simulation is a simplified version of SI M 50-1.) (18cpm/20cpm/23cpm/31cpm(G) machine)
5 Used to adjust the print lead edge image position. (PRINTER MODE)
6 Used to adjust the copy image position and the image loss. (RSPF mode) RSPF
7 Used to adjust the copy image position and the image loss (RSPF mode).  (This simulation is a simplified version of SI M 50-6.) (18cpm/20cpm/23cpm/31cpm(G) machine) RSPF
10 Used to adjust the black print image magnification ratio and the off-center position.  (The adjustment is made separately for each paper feed section.)
12 Used to perform the scan image off-center position adjustment.  (The adjustment is made separately for each scan mode.)
20 Image registration adjustment (Main scanning direction)
22 Used to adjust the image registration. (Main scan direction, sub scan direction)  (Auto adjustment)/OPC drum phase  adjustment (Auto adjustment)
24 Used to display the detail data of SIM 44-2, 50-20, 21 and 22.
27 Used to perform the image loss adjustment of scanned images in the FAX or image send mode.
28 Used to automatically adjust the image loss, void area, image off-center, and image magnification ratio.
51 1 Used to adjust the ON/OFF timing of the secondary transport voltage. 2 Used to adjust the contact pressure (deflection amount) on paper by the main unit and the RSPF resist roller. (This adjustment is performed when there is a  considerable variation in the print image position on 
the paper or when paper jams frequently occur.)
53 6 Used to adjust the detection level of the RSPF document width.
7 Used to adjust the RSPF  document size width sensor.
8 Used to adjust the document lead edge refere nce and the RSPF mode document scan position.
55 1 Used to set the specifications of  the engine control operations. (SOFT SW)
2 Used to set the specifications of t he scanner control operation. (SOFT SW)
3 Used to set the specifications of the controller operation. (SOFT SW)
10 Used to set the special stamp text. (Taiwan only)
56 1 Used to transport data between HDD - MFP  PWB SRAM/EEPROM. (Used to repair the PWB.)
2 Used to backup the data in the EEPROM. SD Card , and HDD (including user authentication data and 
address data) to the USB memory. (Corresponding to the device cloning and the storage backup.)
3 Used to backup the document filing data to the USB memory.
4 Used to backup the JOB log data to the USB memory.
5 Used to import the SIM22-6 data to a USB memory in the TEXT format.
11 Used co copy the SD Card  data to an option HDD. MFP PWB/HDD
12 Used co copy the SD Card  data to an option HDD. MFP PWB/HDD
60 1 Used to check the memory operations (read/write) of the MFP PWB.
61 1 Used to check the LSU polygon motor rotation and laser detection. LSU
3 Used to set the laser power 
4 Used to print the print image skew adjustment pattern. (LSU unit)
62 1 Used to format the hard disk/SD Card. (HDD: Excluding the Operation manual and the watermark data)  (SD Card: User data)
2 Used to check read/write of the hard disk (partial).
3 Used to check read/write of the hard disk (all areas).
6 Used to perform the self diagnostics of the hard disk.
7 Used to print the hard disk self diagnostics error log.
8 Used to format the hard disk/SD Card. (HDD: Excluding the Operation Manual, the watermark data, and  the system area) (SD Card: User data)
10 Used to clear the job completion list data. 11 Used to delete the document filing data.
12 Used to set Enable/Disable of auto format in a hard disk trouble.
13 Used to format the hard disk. (Operation Manual, watermark data only)
14 Used to delete the document filing management data. HDD
15 Used to convert the setting data  for document filing reprint. MFP
20 Used to check the operation of the mirroring hard di sk. (26cpm/36cpm/31cpm(A) machine)Mirroring hard disk
63 1 Used to display the shading correction result. Scanner
2 Used to perform shading.
3 Used to perform scanner (CCD) color  balance and gamma auto adjustment. Scanner
4 Used to display the SIT chart patch density.
5 Used to perform the scanner (CCD) color balance and gamma default setting.
6 Used to display the scan level and the density level of the copy color balance adjustment patch.
7 Used to register the service target of the copy mode auto color balance adjustment.
8 Used to set the default of the service target of the copy mode auto color balance adjustment.
11 Used to set the target color balance of the copy mode auto color balance adjustment.
64 1 Test print. (Self print) (Color mode)
2 Test print. (Self print) (Monochrome mode)
4 Printer test print. (Self print)
5 Printer test print. (Self print) (PCL)
6 Printer test print. (Self print) (PS)
7 Used to print the adjustment pattern of the test print .(Self print). (The adjustment pattern of SIM46-21 is printed.)
Main Sub
Functions Section 
						

							MX-3610N  SIMULATION  5 – 9
65 1 Used to adjust the touch panel (LCD display section) detection coordinates.Operation panel section
2 Used to display the touch panel (LCD  display section) detection coordinates.
5 Used to check the operation panel key input.
66 1 Used to display the FAX-related soft SW (2 - 150) on the LCD to allow changing the soft SW while  checking with the LCD. FAX
2 Used to enter a country code and set the default value for the country code. FAX
3 Used to check read/write of the EEPROM and the SDRAM on the MODEM controller and display the  result. FAX
4 Used to send the selected signals to the line and the main unit speaker. (Send level: max.)  FAX
5 Used to send the selected signal to the line and the main unit speaker. (Send level: Soft SW setting)  (For the kinds of send signals, refer to SIM66-04.) FAX
6 Used to print the confidential registration check ta ble (BOX NO., BOX name, passcode. (If there is no 
confidential registration, no print is made.) FAX
7 Used to output all image data saved in the image memory. (Confidential data are also outputted.) FAX
8 Used to send the selected sound messages to the line and the speaker. (Send level: Max.) FAX
9 Used to send the selected sound message to the line and the speaker. (Send level: Soft SW setting)  * For details of sound messages, refer to  the sound message table of SIM66-08. FAX
10 Used to clear the FAX and image send image data.  (The confidential data are also cleared.)FAX
11 Used to send the selected signal at 300bps to the line and the speaker. (Send level: Max.) FAX
12 Used to send the selected signal at 300bps to the line and the speaker. (Send level: Soft SW setting)  * For the kings of send signals at 300bps, re fer to SIM66-11, 300bps send signal table. FAX
13 Used to register dial numbers for SIM66-14/15/16,  Dial test. (Up to 20 digits can be registered.)FAX
14 Used to execute the dial pulse (10PPS)  send test and to adjust the make time. FAX
15 Used to execute the dial pulse (20PPS)  send test and to adjust the make time. FAX
16 Used to execute the DTFM signal send test and to adjust the send level. FAX
17 Used to send the DTMF signal to the line and the speaker. (Send level: Max.) FAX
18 Used to send the DTMF signal to the line and the speaker. (Send level: Soft SW setting) FAX
21 Used to print the selected items (system error, protocol monitor). FAX
22 Used to set the handset sound volume. (This simulation can be executed even though the handset  setting is set to NO. When, however, the handset is not installed, the sound volume cannot be checked.) 
(Japan model only) FAX
24 Used to clear the FAST save data. FAX
29 Used to initialize the telephone book data (the one- touch registration table, the FTP/Desktop expansion 
table, the group expansion table, the program registration table, the interface memory box table, the 
meta data, InboundRouting, and the DocumentAdmin table). FAX
30 Used to display the TEL/LIU status change, T he display is highlighted by status change. FAX
31 Used to set ON/OFF the port for output to TEL/LIU. FAX
32 Used to check the fixed data received from the line and to display the result. FAX
33 Used to execute detection of various signals with t he line connected and to display the detection result. 
When a signal is detected, the display is highlighted. FAX
34 Used to execute the send test and display the time  required for sending image data in the test. Used to 
execute send test and display. (Unit: ms) FAX
36 Used to check send and receive data from the MODEM  controller to the MFP controller or the data line 
or the command line individually. FAX
39 Used to check and change the destination setting saved in EEPROM of the FAX BOX. FAX
42 Used to rewrite the program to power control installed in the FAX BOX. FAX
43 Used to write the adjustment value into the power control installed in the FAX BOX. FAX
61 Used to display the FAX-related soft SW (151 - 250) on the LCD to allow changing the soft SW while  checking with the LCD. FAX
62 Used to import the FAX receive data into a USB memory in PDF file type. FAX
67 17 Printer reset Printer
24 Printer color balance adjustment (Auto adjustment) Printer
25 Printer color balance adjustment (Manual adjustment) Printer
26 Used to set the target color balance of the printer mode auto color balance adjustment. Printer
27 Used to set the service target of the printer mode auto color balance adjustment. Printer
28 Used to set the default of the service target of the printer mode auto color balance adjustment. Printer
31 Used to clear the printer calibration value. Printer
33 Used to change the gamma of the printer screen. Printer
34 Used to set the density correction in the printer high density section. (Support for the high density  section tone gap) Printer
36 Used to adjust the density in the low density section. Printer
45 Used to adjust the printer image filter and trapping. Printer
52 Used to set the default of the gamma of the printer screen. Printer
54 Printer color balance adjustment (Automatic adjustme nt for each dither (The adjustment is disable in a 
GDI printer.)) Printer
Main Sub
Functions Section 
						

							MX-3610N  SIMULATION  5 – 10
4. Details of simulation
 
1
 1-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the scanner
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1) Select the operation speed with the touch panel key.
2) Press [EXECUTE] key. Scanning is once performed at the speed corresponding to the
scan resolution (operation speed).
 1-2
Purpose
Operation test/check
Function (Purpose)
Used to check the sensors in the scanner
(reading) section and the related circuits.
Section
Scanner (reading)
Operation/Procedure
The operating status of the sensor is displayed.
When MHPS is highlighted, t he scanner unit is in the home posi-
tion.
 1-5
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the scanner
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1) Select the operation speed with the touch panel key.
2) Press [EXECUTE] key. Scanning is repeated at the speed corresponding to the scan
resolution (operation speed).
When [EXECUTE] key is pressed,  the operation is terminated.
 
2
 2-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the auto-
matic document feeder and the control cir-
cuit.
Section
RSPF
Operation/Procedure
1) Select the operation mode and the speed with the touch panel key.
2) Press [EXECUTE] key. The RSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).
When [EXECUTE] key is pressed, the operation is terminated.
[RSPF]
 2-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the sen-
sors and the detectors in the automatic
document feeder section and the control
circuits.
Section
RSPF
Operation/Procedure
The operating conditions of th e sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
SWD_LEN and SWD_AD are not ON/OFF display.
Item/Display Operation mode Default value
OC SCAN 300DPI 300DPI 
(346.0mm/s) 300DPI 
(346.0mm/s)
400DPI 400DPI 
(259.5mm/s)
600DPI 600DPI 
(173.0mm/s)
1200DPI 1200DPI 
(86.5mm/s)
Item/Display Operation mode Default value
OC SCAN 300DPI 300DPI 
(346.0mm/s) 300DPI 
(346.0mm/s)
400DPI 400DPI 
(259.5mm/s)
600DPI 600DPI 
(173.0mm/s)
1200DPI 1200DPI 
(86.5mm/s)
Item/Display Operation mode Default value
 (SINGLE) 300DPI 300DPI 
(259.5mm/s) 300DPI 
(259.5mm/s)
400DPI 400DPI 
(259.5mm/s)
600DPI 600DPI 
(173.0 mm/s)
(DOUBLE) 300DPI 300DPI 
(259.5mm/s) 300DPI 
(259.5mm/s)
400DPI 400DPI 
(259.5mm/s)
600DPI 600DPI 
(173.0 mm/s)
Display Content
SPED Document sensor
SPPD1 Document transport sensor 1
SPLS1 Paper size detector 1
SPLS2 Paper size detector 2
SOCD RSPF open/close sensor
SPPD2 Document transport sensor 2
SPPD3 Document transport sensor 3
SPPD4 Document transport sensor 4
SCOV RSPF cover open/close detector
SSET SPF installation detection
STMPU SPF stamp UN installation detection
SWD_LEN SPF document guide plate position (Unit: 0.1mm)
SWD_AD SPF document detection volume output AD value 
						

							MX-3610N  SIMULATION  5 – 11
 2-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the loads
in the automatic document feeder and the
control circuit.
Section
RSPF
Operation/Procedure
1) Select a target item of the operation check with the touch panel key.
2) Press [EXECUTE] key. The selected load performs the operation.
When [EXECUTE] key is pressed,  the operation is terminated.
 
3
 3-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the sen-
sors and the detectors in the finisher and
the control circuit.
Section
Finisher
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and  the detectors which are active
are highlighted.
Inner finisher (MX-FN17) Saddle stitch finisher (MX-FN10)
Display
Content
SPUM_F RSPF paper feed motor (normal rotation)
SPUM_R RSPF paper feed motor (reverse rotation)
SPFM_F RSPF transport motor (normal rotation)
SPFM_R RSPF transport motor (reverse rotation)
SPRS Paper exit roller pressure control solenoid (RSPF)
SRRC  Registration roller clutch (RSPF)
STMPS Stamp solenoid
Display Content
FABHS Paper alignment belt HP sensor
FAPHPS_F Paper alignment plate HP sensor F
FAPHPS_R Paper alignment plate HP sensor R
FDRPS Paper exit roller position sensor
FDTLLS Paper exit tray lower limit sensor
FDTPD Delivery tray paper detector
FDTULS Paper exit tray upper limit sensor
FFL Fan lock signal
FPCHPS Punch home position sensor
FPD Punch unit detection (connector)
FPDFS Punch dust sensor
FPES1 Punch paper edge sensor 1
FPES2 Punch paper edge sensor 2
FPES3 Punch paper edge sensor 3
FPES4 Punch paper edge sensor 4
FPES5 Punch paper edge sensor 5
FPES6 Punch paper edge sensor 6
FPES7 Punch paper edge sensor 7
FPHPS Punch unit home position sensor
FPLD1 Paper height detector 1
FPLD2 Paper height detector 2
FPMRS Punch motor rotation sensor
FPMS Punch mode sensor
FPPD1 Paper entry detector
FPTS Punch timing sensor
FSED Staple empty detector
FSHPS Staple HP sensor
FSLD Staple lead edge detector
FSSHPS Stapler shift home position sensor
FSSS Staple safety sensor
FSSW Safety switch
FSTPD Staple tray paper detector
FTPS Tray position sensor
FATPD Paper alignment tray paper detector
FCD Connection detector
FCD1 Cover detector 1
FCD2 Cover detector 2
FDRHS Delivery roller home position sensor
FDTPD Delivery tray paper detector
FFL Fan lock signal
FGHPS Gripper home position sensor
FPAPHS_F Paper alignment plate home position sensor F
FPAPHS_R Paper alignment plate home position sensor R
FPCHPS Punch home position sensor
FPD Punch unit detection (connector)
FPDD Delivery detector
FPDFS Punch dust sensor
FPES1 Punch paper edge sensor 1
FPES2 Punch paper edge sensor 2
FPES3 Punch paper edge sensor 3
FPES4 Punch paper edge sensor 4
FPHHS Paper hold home position sensor
FPHPS Punch unit home position sensor
FPLD Paper surface detector
FPMRS Punch motor rotation sensor
FPMS Punch mode sensor
FPPD1 Paper transport detector 1
FPPD2 Paper transport detector 2
FPPD3 Paper transport detector 3
FPTS Punch timing sensor
FSAPHS Saddle alignment plate home position sensor
FSATPD Saddle paper alignment tray paper detector
FSED Staple empty detector
FSHS Staple home position sensor
FSLS Staple lead edge sensor
FSMRS Saddle motor rotation sensor
FSPGHS Saddle paper guide home position sensor
FSPHS Saddle plate home position sensor
FSRHS Saddle roller home position sensor
FSSCS Saddle staple cover sensor
FSSES Saddle staple sensor
FSSHPS Stapler shift home position sensor
FSSHS Saddle staple home position sensor
FSSSHS Saddle stapler shift home position sensor
FSSSW1 Staple safety switch
FSSSW2 Stapler safety switch 2
FSSW1 Safety switch 1
FSTPD Saddle exit tray paper detector
FTLLD Tray lower limit detector
FTLMRS Tray lift motor rotation sensor
FTPS Tray position sensor
FTULD Tray upper limit detector
PDOS Paper pass cover Open/Close sensor
PDPPD1 Paper pass paper transport detector 1
PDPPD2 Paper pass paper transport detector 2 Display
Content