Sharp Mx 2310u Owners Manual

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 65
 
10-D(18) 
Watermark adjustment 
(Normally not required) 
(26cpm/36cpm/31cpm(A) machine)
General (Purpose):
This adjustment is used to adjust  the reproduction capability of the
watermark in the copy/printer mode.
This adjustment is used for watermark documents (primary output).
The result of this adjustment affects the result of watermark print
(secondary output).
In the printer mode, the watermark density can be adjusted by the
printer driver. That adjustment...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 66
Changing adjustment values of adjustment items A - I and
trade off
3) Enter the adjustment value with 10-key and press [OK] key.
4) Make a copy, and check the adjustment result. Descriptions on the watermark
Kinds of 
watermarks  (Mode 
selected in 
the watermark  copy mode) Density 
value Adjustment 
values of 
adjustment  items A - I Effect
Characters 
appearing. Decrease. The adjustment 
value is 
decreased. The watermark images 
become easy to 
disappear....

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 67
Watermark adjustment in the system setting
System setting 
 Security setting   Watermark print  
Contrast tab
Note for adjusting the watermark with SIM46-54
When the color balance automatic adjustment is executed with
SIM46-74 or SIM46-24 but the containing characters are
reproduced, use SIM46-54 to ex ecute the color balance auto-
matic adjustment for each dither.
However, note the following items.
• When either of item K or L of the PATTERN mode is 42, the...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 68
b. Adjustment procedure
(Auto color balance adjustment by the serviceman)
YES
NO
Is the PCL printer
function provided?
YES NO
YES
NO
Printer color balance and density adjustment (Automatic adjustment) procedure
flowchart (SIM67-24)
Start
Execute ADJ10E(1) (Printer color balance and density
adjustment) (Automatic adjustment). Enter the SIM67-24 mode, and select A4
(11" x 8.5") paper.
Press [EXECUTE] key.
(The adjustment pattern is printed.)
Set the...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 69
1) Enter the SIM 67-24 mode.
2) Press [EXECUTE] key. (A4/11 x 
8.5 or A3/11 x 17 paper is
automatically selected.)
The color patch image (adjustment pattern) is printed out.
3) Set the color patch image (adjustment pattern) paper printed in procedure 2) on the document table.
Place the printed color patch image (adjustment pattern) paper
on the document table so that the thin lines on the paper are
on the left side. Place 5 sheets of white paper on the printed...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 70
6) Check the color balance and density.
(Refer to the item of the printer color balance and density
check.)
When satisfactory color balance and density are not obtained
from the automatic adjustment by selecting the factory target in
procedure 4), change the factory color balance target with SIM
67-26 and repeat the procedures from 1).
If a satisfactory result on the color balance and the density is
not obtained with the automatic adjustment, execute the man-...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 71
1) Enter the SIM 67-25 mode.
2) Press [EXECUTE] key. (A4/11 x 
8.5 or A3/11 x 17 paper is
automatically selected.)
The color balance adjustment pattern is printed. 3) Check that the follow
ing specification is satisfied or the color
balance is satisfactory.
If not, execute the following procedures.
The print density must be c hanged gradually from the lighter
level to the darker level. The density changing direction must
not be reversed.
The density level of...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 72
6) Check the color balance and density.
(Refer to the item of the printer color balance and density
check.)
If the color balance is customized, use SIM 67-27 to register
the color balance as the service target.
If the color balance is not cust omized, this procedure is not
required.
If the customized color balance is registered as the service tar-
get, the automatic color balance adjustment can be made in
the next color balance adjustment.
 
10-F Printer image...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 73
* If a tone gap occurs on part of high density, set 0 to item A and B
The density of high density part decreases. However, the tone
gap is better.
* In case of more increase of the density on high density part, set 1 to item A and B.
The tone gap may occur in high density part.
If the setting values of item C, D, E and F are changed, density of
the high density part is changed.
When these values are changed, be sure to perform the printer
color balance and...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 74
 
10-F(4)
Automatic color balance adjustment by the 
user (Printer color balance automatic 
adjustment ENABLE setting and 
adjustment) (Normally unnecessary to the 
setting change)
a. General
In the user program mode, the user can execute the auto color cal-
ibration (auto adjustment of the printer color balance and density).
This adjustment is to set Enable/ Disable of the above user opera-
tion with SIM 26-53.
This setting must be set to ENABLE only when the...