Sharp Mx 2310u Owners Manual

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 85
3) Enter the SIM 50-12 mode.
4) Select the adjustment mode OC with the scroll key.
5) Enter the adjustment value with 10-key, and press [OK] key.
The entered value is set.
When the set value is increased, the main scanning print posi-
tion is shifted to the front side by 0.1mm.
6) Go to the copy mode, and make a copy.
Repeat the procedures of 1) - 6)  until the above condition is satis-
fied.
 
17-B Scan image off-center adjustment 
(Manual adjustment) (RSPF...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 86
SIM50-6
* Item A, B: When the adjustment value is increased, the scan
timing is delayed.
* Item C - H: When the adjustment value is increased, the image loss is increased.
* Item A - H: 1 step = 0.1mm change
* The SPF rear edge image loss setting is provided for countermeasures against the case when shades are
produced.
5) Select an adjustment mode with the scroll key.
(SIM50-12)
(SIM50-6)
6) Enter an adjustment value with 10-key, and press [OK] key. (Change for...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 87
2) Enter the SIM 50-1 mode.
3) Set RRCA, LEAD, and SIDE to the default values.
4) Perform the image lead edge reference position adjustment.
Shift to the copy mode, and make a copy at each of 100% and
200% in the document table mode.
When the adjustment value of RRCA is proper, the lead edge
image from 4.0mm is not copied in either of 100% and 200%
copy scale.
If not, change and adjust the RRCA value.
(Adjust so that the lead edge im age from 4.0mm is not...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 88
 
18-BImage scanning position adjustment 
(Manual adjustment) (RSPF mode)
This adjustment must be performed in the following cases:
* When the scan control PWB is replaced.
* When the EEPROM on the scan control PWB is replaced.
* When the scanner (reading) section is disassembled.
* When the scanner (reading) section is replaced.
* When U2 trouble occurs.
* When the RSPF section is disassembled.
* When the RSPF unit is replaced.
This simulation is to adjust  the...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 89
* Item A, B: When the adjustment value is increased, the scan 
timing is delayed.
* Item C - H: When the adjustment value is increased, the image loss is increased.
* Item A - H: 1 step = 0.1mm change
* The RSPF rear edge image loss setting is provided for coun- termeasures against the case when shades are produced.
(Lead edge image loss adjustment)
1) Set the lead edge image loss adjustment values (LEAD EDGE (SIDE1/SIDE2) on the front surface and the back...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 90
2) Enter the adjustment value of TRAIL EDGE (SIDE1/SIDE2)
with 10-key, and press [OK] key.
TRAIL EDGE (SIDE 1):  Rear edge image loss adjustment value (Front surface)
TRAIL EDGE (SIDE 2):  Rear edge image loss adjustment value (Back surface)
(When the adjustment value is increased, the rear edge image
loss is increased.)
(Change for change in the set value: 0.1mm/step)
Perform the procedures of 1) - 2) until a satisfactory result is
obtained.
(Front/rear frame...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 91
2) Select an adjustment target item with the scroll key.
Saddle stitch finisher
Item/Display Content Setting 
range Default 
value Purpose (Case where the 
adjustment is required) Change when the adjustment value is 
increased or decreased Change 
when the 
adjustment  value is 
changed by 1
A FRONT  ADJUST Alignment position 
adjustment 
(F side alignment 
plate stop position) 
(Paper alignment 
adjustment) 2 - 18 10 This adjustment is used to 
adjust the paper...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 92
C FRONT ADJUST Alignment position 
adjustment (front) 35 - 65 50 When the paper 
alignment capability 
in the stacker 
section is improper, 
the paper alignment 
width is adjusted. F side paper 
alignment plate stop 
position 
(F/R direction)
When the adjustment value is 
increased, the alignment 
position is shifted to the 
center.
When the adjustment value is 
decreased, the alignment 
position is shifted to the 
outside. 0.2mm
D REAR  ADJUST Alignment...

MX-3610N  ADJUSTMENTS AND SETTINGS  4 – 93
3) Enter an adjustment value and press [OK] key.
4) Cancel the simulation, make a copy in the mode incl
uding the adjustment target, and check the adjustment result.
L PUNCH HOLE Punch hole 
position 
adjustment30 - 60 50 When the punch 
hole position is 
shifted in the 
transport direction, 
the adjustment is 
executed. Punch position 
(paper transport 
direction)
When the adjustment value is 
increased, the punch hole 
position is shifted to the rear 
edge of...

MX-3610N  SIMULATION  5 – 1
MX-3610N
Service Manual [5] SIMULATION
1. General and purpose
The simulation mode has the following functions, to display the
machine operating status, identify the trouble position and causes
in an earlier stage, and to efficiently setup and adjust the machine
for improved serviceability.
1) Various adjustments
2) Setting of the specifications and functions
3) Canceling troubles
4) Operation check
5) Counters check, setting, clear
6) Machine operating conditions 
(operation...