Sharp Mx 2300n Service Manual

MX-2300/2700 N/G  SIMULATION  7 – 85 
* Items M are displayed as Display item: Detail of display.
Example: EXECUTE MODE: AUTO

When [EXECUTE] button is pressed after changing and settlement
of the exposure adjustment values A to L, the data are saved to
EEPROM and RAM and reflected to item M at the same time.
 
46-44
Purpose: Adjustment
Function (Purpose): Used to execute the FAX exposure adjust-
ment (Ultra Fine). (Only when FAX is
installed)
Section:MFP/FAX
Item: Image qualityOperation/Procedure
1)...

MX-2300/2700 N/G  SIMULATION  7 – 86 * Items M are displayed as Display item: Detail of display.
Example: EXECUTE MODE: AUTO

When [EXECUTE] key is pressed after changing and settlement of
exposure adjustment values A to L, the data are saved to EEPROM
and RAM and set to item M at the same time.
 
46-45
Purpose: Adjustment
Function (Purpose): Used to execute the FAX exposure level
adjustment and the individual setting
(600DPI). (Only when FAX is installed)
Section:FAX
Item: Image...

MX-2300/2700 N/G  SIMULATION  7 – 87
 
46-47
Purpose: Setting
Function (Purpose): Used to set the JPEG compression rate in
Copy/Scanner (PUSH SCAN).
Section:—
Item: SettingOperation/Procedure
1) Select the set item with [↑] and [↓] buttons.
The highlighted set value is switched and the value is dis-
played in the setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display grays out and the
operation is invalid.
If there is any...

MX-2300/2700 N/G  SIMULATION  7 – 88 
* When the set value is increased by 1, the magnification ratio is
increased by 0.02%.
* This adjustment affects PC scanning and other scanning other
than copy.
 
48-5
Purpose: Adjustment
Function (Purpose): This adjustment is executed when a satis-
factory result is not obtained when a differ-
ent copy magnification ratio is specified and
copying is made after adjustment of the sub
scanning direction image magnification
ratio with SIM 48-1.
When there is an error in...

MX-2300/2700 N/G  SIMULATION  7 – 89 * Copying can be performed also by pressing [COLOR]/
[BLACK] key.
* When [CLOSE] button is pressed, the display is shifted to
the copy basic screen of simulation.

*1: Common to COLOR, MONO, and HEAVY paper. The item is
displayed only when COLOR button is highlighted.
* Since the belt is driven in cooperation with the developing K
motor (DVM-K) in this machine, the DVM-K also serves as the
belt motor (BTM).
* Adjustment value
The greater the correction value is, the...

MX-2300/2700 N/G  SIMULATION  7 – 90 
*1: Not supported for the MX-2300/2700 series.

 
49-3
Purpose: Version-up
Function (Purpose): The Operation Manual saved in the hard
disk is updated.
Section:—
Item: Adjustment
Operation/Procedure
1) Insert the USB memory into the machine.
* When USB is not connected, INSERT A STORAGE E-
MANUAL STORED ON is displayed. When [OK] button is
pressed, the display is shifted to the folder selection screen
1.
2) When a operation manual update folder button is pressed, the...

MX-2300/2700 N/G  SIMULATION  7 – 91 

 
50
 
50-1
Purpose: Adjustment
Function (Purpose): Used to adjust the copy image position on
print paper in the copy mode and to adjust
the void area (image loss). (The similar
adjustment can be executed with SIM50-05
and 50-02 (Simple method). (Document
table mode))
Section:—
Item: Image quality (Image position)
Operation/Procedure
1) Select the set item with [↑] and [↓] buttons.
The highlighted set value is switched and the value is dis-
played in the setting...

MX-2300/2700 N/G  SIMULATION  7 – 92
 
50-2
Purpose: Adjustment
Function (Purpose): Used to adjust the copy image position on
print paper in the copy mode and to adjust
the void area (image loss). (Simple adjust-
ment)
(Similar to SIM50-01. This simulation pro-
vides the simpler method.)
Section:–
Item: Image quality (Image position)
Operation/Procedure
1) In advance to this adjustment, execute the magnification ratio
adjustment in the sub scanning direction (SIM48-01).
2) Select TRAYand set 0 to L1 and...

MX-2300/2700 N/G  SIMULATION  7 – 93
 
50-5
Purpose: Adjustment
Function (Purpose): Used to set the lead edge adjustment value
which affects only the printer print.
Section: Printer
Item: Image quality
Operation/Procedure
1) Select the set item with [↑] and [↓] buttons.
The highlighted set value is switched and the value is dis-
played in the setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display grays out and the
operation...

MX-2300/2700 N/G  SIMULATION  7 – 94 If there is any item under [↓], an active display is made and
item is shifted.
If there is no item over [↓], the display grays out and the
operation is invalid.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
3) When [OK], [↑], [↓] button, [COLOR], or [BLACK] key is
pressed, it is highlighted and the currently entered data are
saved to EEPROM and RAM.
* When [CLOSE] button is pressed, the display is shifted to the
copy basic screen of...