Sharp Mx 2300n Service Manual

MX-2300/2700 N/G  SIMULATION  7 – 105 * When [BACK] button is pressed, the display returns to the result
display screen.

 
50-28
Purpose: Adjustment
Function (Purpose): Used to display the adjustment result.
(Auto void adjustment (Service installation
adjustment) (5: result display)
Section:—
Item: Image quality
Operation/Procedure
1) When [RESULT] button is pressed on the top menu screen,
the screen on the right is displayed.
2) When [BACK] button is pressed, the display is shifted to the
top menu...

MX-2300/2700 N/G  SIMULATION  7 – 106
 
51
 
51-1
Purpose: Adjustment
Function (Purpose): Used to adjust the ON/OFF timing of the
transfer voltage and the separation bias
voltage.
Section:Process
Item: Operation (Transfer)
Operation/Procedure
1) Select the set item with [↑] and [↓] buttons.
The highlighted section of the set value is switched and dis-
played on the set setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display...

MX-2300/2700 N/G  SIMULATION  7 – 107 If there is no item over [↓], the display grays out and the
operation is invalid.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.3) When [OK], [↑], [↓] button, [COLOR], or [BLACK] key is
pressed, the current entered value is saved to EEPROM and
RAM.
* When [CLOSE] button is pressed, the display shifts to the
copy basic screen of simulation.


(Small size): The paper length in the transport direction is LT
(216mm) or less.
(Large...

MX-2300/2700 N/G  SIMULATION  7 – 108
 
53
 
53-6
Purpose: Adjustment
Function (Purpose): Used to adjust the RSPF document tray
size of the main unit.
Section:RSPF
Item: Operation
Operation/Procedure
1) Set the tray document guide to the max. width position, and
press [EXECUTE] key. The button is highlighted and the tray
size volume maximum value adjustment is started.
* During the adjustment, EXECUTING... is displayed.
* After completion of the tray size volume maximum value
adjustment, the set value is...

MX-2300/2700 N/G  SIMULATION  7 – 109 • When the set value is changed by 1, the position is shifted by
0.1mm.
• Since the distance of RRCA-S and RSPF scan position is
changed, RRCA and RRCA-S are not changed by this adjust-
ment value.
 
55
 
55-1
Purpose: Setting
Function (Purpose): Used to set the engine soft SW.
Section:PCU
Item: Operation (Specifications)
Operation/Procedure
1) When the machine enters Simulation 55-01, the screen on the
right is displayed.
* On the initial screen, [SW-NO.] button is...

MX-2300/2700 N/G  SIMULATION  7 – 110
 
56
 
56-1
Purpose: Data transfer
Function (Purpose): Used to execute data transfer.
Section:MFP
Item: Data transfer
Operation/Procedure
1) Select an item of data transfer.
* The selected button is highlighted and ENABLE is dis-
played in the corresponding display section.
* When another button is selected, the newly selected button
is highlighted and ENABLE is displayed in the correspond-
ing display section. The previously selected button returns to
the normal...

MX-2300/2700 N/G  SIMULATION  7 – 111
 
60
 
60-1
Purpose: Operation test/Check
Function (Purpose): Used to check read/write of the expansion
DIMM installed to the ICU PWB.
After completion of execution, the result of
each slot is displayed on the panel.
ICU PWB image DRAM read/write opera-
tion check, check ICU (memory) operation.
Section: Image process (ICU)
Item: Operation
Operation/Procedure
1) When the machine enters Simulation 60-01, the screen on the
right is displayed.
When [EXECUTE] button is...

MX-2300/2700 N/G  SIMULATION  7 – 112
 
61
 
61-01
Purpose: Operation test/Check
Function (Purpose): The polygon motor rotation and the BD sig-
nal detection are checked.
Section:LSU
Item: Operation
Operation/Procedure
1) When [EXECUTE] button is pressed, the LSU check is started.
2) When checking is normally completed, [OK] is displayed.
When an error occurs in checking, [NG] is displayed and the
detail is displayed.
E TRAS SETTING VALUE 4CLOCK TRAS setting value 0 2
5CLOCK 1
6CLOCK 2
7CLOCK 3
F TRC...

MX-2300/2700 N/G  SIMULATION  7 – 113
 
61-4
Purpose: Adjustment
Function (Purpose): Used to execute self-print of the LSU posi-
tion adjustment.
Section:LSU
Item: Adjustment
Operation/Procedure
1) Select the set item with [↑] and [↓] buttons.
The highlighted section of the set value is switched and dis-
played on the set setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display grays out and the
operation is invalid.
If there...

MX-2300/2700 N/G  SIMULATION  7 – 114 * When the procedures (Write → Retrieve → Abnormality
check) are completed normally, [EXECUTE] button returns
to the normal display and [YES] and [NO] buttons gray out.
* When [CA] key is pressed during the procedures (Write →
Retrieve → Check for any abnormality.), the operation is
interrupted and the simulation is terminated. When [SYS-
TEM SETTINGS] key is pressed, the operation is interrupted
and the display returns to the sub number entry screen.
 
62-3
Purpose:...