Sharp Mx 2300n Service Manual

MX-2300/2700 N/G  SIMULATION  7 – 115
 
62-8
Purpose: Data clear
Function (Purpose): Used to format the hard disk excluding the
system area and operation manual area.
* Be sure to format the HDD in FAT32.
Section: MFP (HDD)
Item: Clear
Operation/Procedure
1) Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.
2) Press [YES] button.
3) The hard disk (excluding the system area) is formatted. [YES]
button is highlighted.
* When [NO] button or [EXECUTE] button is...

MX-2300/2700 N/G  SIMULATION  7 – 116
 
62-12
Purpose: Data clear
Function (Purpose): Used to set Enable/Disable of auto format
in HDD trouble.
* Be sure to format the HDD in FAT32.
Section: MFP (HDD)
Item: Clear
Operation/Procedure
1) When the machine enters the simulation, the screen on the
right is displayed.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
3) When [OK] button, [COLOR], or [BLACK] key is pressed, it is
highlighted and the current entered value is saved...

MX-2300/2700 N/G  SIMULATION  7 – 117 * On the screen, [G] is pressed.
 
63-2
Purpose: Adjustment
Function (Purpose): Used to execute shading forcibly.
Section: Scanner
Item: Operation
Operation/Procedure
1) When [EXECUTE] button is pressed, it is highlighted and
shading is started.
* During execution, SHADING EXECUTING... is displayed.
* When [EXECUTE] button is pressed during execution, the
operation is interrupted.
* When shading is completed normally, [EXECUTE] button
returns to the normal display...

MX-2300/2700 N/G  SIMULATION  7 – 118
 
63-5
Purpose: Adjustment
Function (Purpose): Used to reset the gamma correction and
color correction parameters of the SCAN
ASIC.
Section: Scanner
Item: Clear
Operation/Procedure
1) When a touch panel button to execute the standard reset is
pressed ([SIDE A(OC)] in this example), the selected button is
highlighted and [EXECUTE] button becomes active from the
gray-out display.
* When the selected button is pressed again, selection is can-
celed and the button...

MX-2300/2700 N/G  SIMULATION  7 – 119
 
63-8
Purpose: Setting
Function (Purpose): Used to execute the standard value reset of
the engine auto adjustment scanner target
value (for servicing).
Section: Image process (ICU)
Item: Image quality (Color balance)
Operation/Procedure
1) Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.
2) Press [YES] button.
The standard value reset of the engine auto adjustment scan-
ner target value is executed. [YES] button is...

MX-2300/2700 N/G  SIMULATION  7 – 120 
* Paper feed condition PLAIN: Cassette/Manual feed. For the other, manual feed only.
* Items F, G, H, I are displayed as Display item: Detail of display.
Example: PAPER:CS1
Item Display item Description of item Set range Default value Writing
A PRINT PATTERN (1, 2, 9 ~ 11, 14 ~ 19) Print pattern specification 
(* For details, refer to the following.)1 to 20
(Only 1, 2, 9 to 11, 
and 14 to 19 can 
be printed.) 1Yes
B DOT1 (DOT1>=2 IF A : 2, 11) Print dot number...

MX-2300/2700 N/G  SIMULATION  7 – 121 
NO. ContentPattern 
sizePattern 
forming 
sectionColor selectGradation 
selectExposure 
selectM parameter N parameter
Remark
ConditionWhen 
NOEnable/ 
DisableDefault 
valueEnable/ 
DisableDefault 
value
1 Grid pattern All 
surfaceLSU-ASIC{K only{✕{1{254 • All colors are 
selected in the print 
width of 100 or more 
(Print in 3 colors 
(CMY), print is 
started at 4mm from 
the paper lead edge.
2 Mesh print{K only{✕{2{2–
3 16 gradations: 
sub scanSub 
fixed{ (up to 
3...

MX-2300/2700 N/G  SIMULATION  7 – 122
 
64-2
Purpose: Adjustment/Setup/Operation data output/
Check (Display/Print)
Function (Purpose): Used to print the density adjustment pat-
tern.
Section: Printer
Item: Operation
Operation/Procedure
1) Select the set item with [↑] and [↓] buttons.
The highlighted set value is switched and the value is dis-
played in the setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display grays out and...

MX-2300/2700 N/G  SIMULATION  7 – 123 2) Enter the set value with 10-key.
* When [C] key is pressed, the entered value is cleared.
3) When [EXECUTE] button is pressed, it is highlighted and print-
ing is started.
* After completion of printing, [EXECUTE] button returns to
the normal display.* When [OK], [↑], [↓] button, [COLOR], or [BLACK] key is
pressed, the value is set to the set item. (The value is not
saved to EEPROM and RAM.)
* When [C], [CA], [SYSTEM SETTINGS], or [EXECUTE] key
is pressed during...

MX-2300/2700 N/G  SIMULATION  7 – 124 
NO. ContentPattern 
sizePattern 
forming 
sectionGradation 
selectExposure 
selectM parameter N parameter
Remark
Enable/ 
DisableDefault 
valueEnable/ 
DisableDefault 
value
1 Grid pattern  All surface LSU-ASIC{✕{1{254 • When all colors are 
selected in the print width 
of 100 or more, print is 
made in CMY (3 colors).
• Print is started at 4mm 
from the paper lead edge. 
2 Mesh print All surface{✕{2{2–
3 16 gradations: sub 
scanSub fixed No✕✕ ✕• When all colors are...