Sharp Mx 2300n Service Manual

MX-2300/2700 N/G  SIMULATION  7 – 25
 
24-2
Purpose: Data clear
Function (Purpose): Used to clear the number of use (the num-
ber of prints) of each paper feed section.
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel.
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
 
24-3
Purpose: Data clear
Function (Purpose): Used to clear the number of use of the fin-
isher, RSPF, and the scan (reading) unit.
Section:—...

MX-2300/2700 N/G  SIMULATION  7 – 26
 
24-5
Purpose: Data clear
Function (Purpose): Used to clear the developer counter. (After
replacement of developer, clear the
counter.)
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel.
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
 
24-6
Purpose: Data clear
Function (Purpose): Used to clear the copy counter.
Section:—
Item: Counter
Operation/Procedure
1) Select the...

MX-2300/2700 N/G  SIMULATION  7 – 27
 
24-10
Purpose: Data clear
Function (Purpose): Used to clear the FAX counter. (Only when
FAX is installed)
Section:—
Item: Counter
Operation/Procedure
1) Select the item to be cleared with the buttons on the touch
panel. 
2) Press [EXECUTE] button.
3) Press [YES] button.
The target counter is cleared.
 
24-15
Purpose: Data clear
Function (Purpose): Used to clear the counters related to the
image send.
Section:—
Item: Counter
Operation/Procedure
1) Select the item to...

MX-2300/2700 N/G  SIMULATION  7 – 28
 
25
 
25-1
Purpose: Operation test/Check
Function (Purpose): Used to check the operations of the devel-
oping section.
Section: Process (Developing section)
Item: Operation
Operation/Procedure
1) Select the process speed with [MIDDLE] and [LOW] buttons.
2) Press [EXECUTE] button.
The developing motor and the OPC drum motor rotate for 3
min and the detection level of the toner density sensor is dis-
played. 
 
25-2
Purpose: Setting
Function (Purpose): Used to make the...

MX-2300/2700 N/G  SIMULATION  7 – 29
 
26-2
Purpose: Setting
Function (Purpose): Used to set the paper size of the large
capacity tray (LCC). (When the paper size
is changed, this simulation must be exe-
cuted to change the paper size in software.)
Section: Paper feed
Item: Setting
Operation/Procedure
Select the paper size with the buttons on the touch panel. 
 
26-3
Purpose: Setting
Function (Purpose): Used to set the specifications of the auditor.
Section: Auditor
Item: Specifications...

MX-2300/2700 N/G  SIMULATION  7 – 30
 
26-6
Purpose: Setting
Function (Purpose): Used to set the specifications (paper, fixed
magnification ratio, etc.) of the destination.
Section:—
Item: Specifications (Destination)
Operation/Procedure
1) Select the set target with the button on the touch panel.
2) Press [EXECUTE] button.
The selected set content is saved. 
 
26-10
Purpose: Setting
Function (Purpose): Used to set the trial mode of the network
scanner.
Section:—
Item: Operation
Operation/Procedure
1)...

MX-2300/2700 N/G  SIMULATION  7 – 31
 
26-30
Purpose: Setting
Function (Purpose): Used to set allow/inhibit of HL slow-up con-
trol (CE mark support control).
Section:—
Item: Specifications (Operation mode (common
operation))
Operation/Procedure
1) When the machine enters the simulation, the following screen
is displayed.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or...

MX-2300/2700 N/G  SIMULATION  7 – 32 * When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.


 
26-49
Purpose: Setting
Function (Purpose): Used to set the copy speed mode.
Section:—
Item: Setting
Operation/Procedure
1) When the machine enters Simulation 26-49, the current set
status is displayed.
* The current set button is highlighted.
2) Select an item to be changed, and it is highlighted. The setting
is saved to EEPROM and RAM.
* Only one can be selected for each...

MX-2300/2700 N/G  SIMULATION  7 – 33 
 
26-52
Purpose: Setting
Function (Purpose): Used to set whether non-printed paper
(insertion paper, cover paper) is counted up
or not.
Section:—
Item:—
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the entered value is set.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.


 
26-53
Purpose:Setting
Function (Purpose): Used to set YES/NO of...

MX-2300/2700 N/G  SIMULATION  7 – 34
 
26-65
Purpose: Setting
Function (Purpose): Used to set the finisher alarm mode.
Section:—
Item: Specifications
Operation/Procedure
1) When the machine enters Simulation 26-65, the following
screen is displayed.
* The current set value is highlighted.
2) When the set value button of an item to be changed is
pressed, it is highlighted and the setting is saved to EEPROM
and RAM.
* Only one can be selected for each item.


* Valid only when the 1K finisher is...