Sharp Mx 2300n Service Manual

MX-2300/2700 N/G  SIMULATION  7 – 5
27 2 Used to set the FSS function (Password, HOST server TEL number). Communication (RIC/
MODEM)Setting
4 Used to set the FSS functions (initializing, call, toner order auto send). Communication (RIC/
MODEM)Setting
5 Used to set the tag number. Communication (RIC/
MODEM)Setting
6 Used to set YES/NO of the manual service call. Communication (RIC/
MODEM)Setting
7 Used to set the FSS functions (enable, alert callout). Communication (RIC/
MODEM)Setting
9 Used to set the...

MX-2300/2700 N/G  SIMULATION  7 – 6
44 22 Used to check the toner patch image density level of each color in half tone 
image forming section correction (process correction). (This simulation is used 
to check that the correction is normally executed or not.)Process Adjustment/Setup/Operation 
data output/Check (Display/Print)
24 (This simulation is not used in the market.) 
Used to display the process control result.Process Adjustment/Setup/Operation 
data output/Check (Display/Print)
25 Used to check...

MX-2300/2700 N/G  SIMULATION  7 – 7
48 5 This adjustment is executed when a satisfactory result is not obtained when a 
different copy magnification ratio is specified and copying is made after 
adjustment of the sub scanning direction image magnification ratio with SIM 48-
1.
When there is an error in the copy magnification ratio in reduction copy, the 
adjustment value of high speed mode is adjusted.
When there is an error in the copy magnification ratio in enlargement copy, the 
adjustment value of...

MX-2300/2700 N/G  SIMULATION  7 – 8
56 1 Used to execute data transfer. MFP Data transfer
2 Used to backup the data (user authentication data, address book, etc.) of 
EEPROM, SRAM, or HDD to a USB memory and to restore the data.Memory, HDD Backup
60 1 Used to check read/write of the expansion DIMM installed to the ICU PWB.
After completion of execution, the result of each slot is displayed on the panel.
ICU PWB image DRAM read/write operation check, check ICU (memory) 
operation.Image process (ICU)...

MX-2300/2700 N/G  SIMULATION  7 – 9
3. Details of simulation
 
1
 
1-1
Purpose: Operation test/check
Function (Purpose): Used to check the operations of the scan-
ner unit and its control circuit.
Section: Optical (Image scanning)
Item: Operation
Operation/Procedure
1) Select the operation mode with the buttons on the touch panel.
2) Select the magnification ratio with [ZOOM] button on the touch
panel.
3) Press [EXECUTE] button.
The scanner scans at the speed corresponding to the opera-
tion mode.
 
1-2...

MX-2300/2700 N/G  SIMULATION  7 – 10
 
2-2
Purpose: Operation test/check
Function (Purpose): Used to check the operations of the sen-
sors and detectors in the automatic docu-
ment feeder unit and the related circuits.
Section:RSPF
Item: Operation
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
NOTE: SWD_LEN and SWD_AD are not ON/OFF display.
 
2-3
Purpose: Operation test/check
Function (Purpose): Used to check...

MX-2300/2700 N/G  SIMULATION  7 – 11 


 
3-3
Purpose: Operation test/check
Function (Purpose): Used to check the operation of the load in
the finisher and the control circuit.
Section: Finisher
Item: Operation
Operation/Procedure
1) Select the item to be checked with the buttons on the touch
panel.
2) Press [EXECUTE] button.
The selected load operation is performed.
When [EXECUTE] button is pressed, the operation is termi-
nated.




FLE Lift lock detection
FSHPD Staple drive HP detection 
FSTHPD Staple...

MX-2300/2700 N/G  SIMULATION  7 – 12
 
3-10
Purpose: Adjustment
Function (Purpose): Used to adjust the finisher.
Section: Finisher
Item: Operation
Operation/Procedure
1) Select the item according to the adjustment content with [↑] [↓]
buttons.
2) Enter the adjustment value with 10-key.
3) Press [OK] button. (The set value is saved.)

[Screen (Saddle finisher installed)]
 
4
 
4-2
Purpose: Operation test/check
Function (Purpose): Used to check the operations of the sen-
sors and detectors in the...

MX-2300/2700 N/G  SIMULATION  7 – 13
 
4-3
Purpose: Operation test/check
Function (Purpose): Used to check the operations of the loads
in the large capacity tray and the related cir-
cuit.
Section: Desk/Large capacity tray (LCC)
Item: Operation
Operation/Procedure
1) Select the item to be checked with the buttons on the touch
panel.
2) Press [EXECUTE] button.
The selected load operation is performed.
When [EXECUTE] button is pressed, the operation is termi-
nated.


 
4-5
Purpose: Operation test/check...

MX-2300/2700 N/G  SIMULATION  7 – 14
 
5-3
Purpose: Operation test/check
Function (Purpose): Used to check the operation of the scanner
lamp and the circuit.
Section: Optical (Image scanning)
Item: Operation
Operation/Procedure
1) Press [OC COPY LAMP] button on the touch panel.
2) Press [EXECUTE] button.
The target lamp is lighted for 10 sec.
 
5-4
Purpose: Operation test/check
Function (Purpose): Used to check the operation of the dis-
charge lamp and the related circuit.
Section:Process
Item:...