Sharp Lc 46le814 Operation Manual

9
Attaching the stand unit
•	Before	performing	work,	spread	cushioning	over	the	surface	on	which	you	will	be	laying	the	TV.	This	will	prevent	it	from	being	damaged.
CAUTION•	Attach the stand in the correct direction.•	Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
 1Confirm that there are nine screws (four long screws and five short screws) with the stand unit.
 2Attach the supporting post for the stand unit onto the base using the four long...

10
Using the remote control unit
Inserting the batteries
Before	using	the	TV	for	the	first	time,	insert	two	supplied	“AAA”	size	alkaline	batteries.	When	the	batteries	become	depleted	and	the	remote	control	unit	fails	to	operate,	replace	the	batteries	with	new	“AAA”	size	batteries.
 1Open the battery cover.
 2Insert two supplied “AAA” size alkaline batteries.•	Place	batteries	with	their	terminals	corresponding	to	the	(e)	and	(f)	indications	in	the	battery	compartment.
 3Close the battery cover....

11
Initial installation overview
Follow	the	steps	below	one	by	one	when	using	the	TV	for	the	first	time.	Some	steps	may	not	be	necessary	depending	on	your	TV	installation	and	connection.
Preparation
 nConnect an antenna cable to the antenna terminal (Page 12).
 oIf necessary, insert a CA card into the CI slot to watch scrambled broadcasts (Page 12).
 pPlug the AC cord into the AC outlet (Page 12).
Product	shape	varies	in	some	countries.
Run the initial 
settings
 nCheck that the MAIN POWER switch on the...

12
Before turning on the power


 
21

 nStandard DIN45325 plug (IEC 169-2) 75 q coaxial cable
 oSatellite antenna cable
 pAC cord (product shape varies in some countries)
 qCheck that the MAIN POWER switch on the rear of the TV is turned on (;).
 rCable clamp (bundle the cables with the clamp)
Place	the	TV	close	to	the	AC	outlet,	and	keep	the	power	plug	within	reach.
Inserting the CA card into the CI module
In	order	to	receive	coded	digital	stations,	a	common	interface	module	(CI	module)	and	a	CA...

13
Initial auto installation
When	the	TV	is	powered	on	for	the	first	time	after	purchase,	the	initial	auto	installation	wizard	appears.	Follow	the	menus	and	make	the	necessary	settings	one	after	another.
Confirm the following before turning on 
the power
	
E Is	the	antenna	cable	connected?
	
E Is	the	AC	cord	plugged	in?
	
E Is	the	MAIN	POWER	switch	turned	on	(;)?
 1Press 	“View	setting”	>	“Reset”	>	select	“HOME”	again.
 4Setting the country.Press	a/b/c/d	to	select	your	country	or	area,	and	then	press	;.•...

14
Quick guide
 ESearching for cable broadcasts
To change each item to the appropriate settings:	1Press	a/b	to	select	the	menu,	and	then	press	;.
Scrambled stations[Yes]
Search method[Channel]
Start frequency
Network ID [None]
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Reset
Search start
	2Press	a/b/c/d	or	0_9	to	select	or	input	the	appropriate	item/value,	and	then	press	;.	3Press	a/b	to	select	“Search	start”,	and	then	press	;.	4Press	c/d	to	select	“Yes”	to	start	searching	cable...

15
Searching for satellite broadcasts
Press	c/d	to	select	“Yes”,	and	then	press	;.
YesNo
•	If	you	do	not	perform	“Satellite	search”	setting,	select	“No”,	and	then	press	;.•	The	current	DVB-S/S2	setting	screen	is	displayed.
Next
other
SatelliteLNB Frequency
Low High
Satellite System
Max. 4 satellites on DiSEqC multiswitch
Change setting
•	You	must	first	complete	“Change	setting”	before	moving	to	the	“Next”	setting.
 1When starting the satellite search after setting the scrambled stations:
Press c/d to...

16
 2When you change the antenna connection setting:
Press c/d to select “Change setting” on the DVB-S/S2 setting screen in the left column, and then press ;.•	The	antenna	connection	setting	screen	is	displayed.
Single satellite
2 satellites on 22kHz switchbox
2 satellites on toneburst switchbox
Max. 4 satellites on DiSEqC multiswitch
Communal satellite system
NOTE•	You	can	select	the	antenna	connection	method	from	the	five	types.	Consult	your	dealers	before	using	a	method	other	than	“Single	satellite”....

17
Quick guide
Checking signal strength and 
channel strength (DVB-T/C/S/S2)
If	you	install	a	DVB-T/C/S/S2	antenna	for	the	first	time	or	relocate	it,	you	should	adjust	the	alignment	of	the	antenna	to	receive	a	good	reception	while	checking	the	antenna	setup	screen.
 1Go to “Menu” > “Setup” > “View setting” > “Channel settings” > “Antenna setup-DIGITAL”.
 2Press a/b to select “Digital setup” or “Satellite setup”, and then press ;.
 EChecking signal strength
 3Press a/b to select “Signal strength”, and...

18
Daily operation
Switching on/off
Turning on/off the power
 1Turn on (;) the MAIN POWER switch on the rear of the TV (Page 5).
 2To turn on the TV, press a on the remote control unit.
 3To turn off the TV, press a on the remote control unit.
 4Turn off (a) the MAIN POWER switch on the rear of the TV (Page 5).•	When	turning	off	the	power	using	the	MAIN	POWER	switch	on	the	rear	of	the	TV,	EPG	data	will	be	lost.
Standby mode
 ETo standby modeIf	the	MAIN	POWER	switch	on	the	rear	of	the	TV	is	turn	on	(;),...