Sharp Lc 46le814 Operation Manual

							9
Attaching the stand unit
•	Before	performing	work,	spread	cushioning	over	the	surface	on	which	you	will	be	laying	the	TV.	This	will	prevent	it	from	being	damaged.
CAUTION•	Attach the stand in the correct direction.•	Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
 1Confirm that there are nine screws (four long screws and five short screws) with the stand unit.
 2Attach the supporting post for the stand unit onto the base using the four long screws with a screwdriver as shown.
Supporting	post
 3Insert the stand into the openings on the bottom of the TV (hold the stand so it will not drop from the edge of the base area).
Soft	cushion
 4Insert and tighten four short screws into the four holes on the rear of the TV.
 5Attaching the stand cover.	1Slide	the	stand	cover	into	the	two	catches	on	the	stand	base.	2Insert	and	tighten	a	short	screw	into	the	hole	on	the	centre	of	the	stand	cover.
NOTE•	To	detach	the	stand	unit,	perform	the	steps	in	reverse	order.•	A	screwdriver	is	not	supplied	with	this	product.•	The	stand	base	is	made	of	glass.	Therefore,	be	careful	not	to	drop	the	stand	base	or	apply	pressure	to	it.•	Do	not	place	heavy	objects	on	the	stand	base.
CAUTIONThe
Preparation
  
						

							10
Using the remote control unit
Inserting the batteries
Before	using	the	TV	for	the	first	time,	insert	two	supplied	“AAA”	size	alkaline	batteries.	When	the	batteries	become	depleted	and	the	remote	control	unit	fails	to	operate,	replace	the	batteries	with	new	“AAA”	size	batteries.
 1Open the battery cover.
 2Insert two supplied “AAA” size alkaline batteries.•	Place	batteries	with	their	terminals	corresponding	to	the	(e)	and	(f)	indications	in	the	battery	compartment.
 3Close the battery cover.
CAUTIONImproper	use	of	batteries	can	result	in	chemical	leakage	or	explosion.	Be	sure	to	follow	the	instructions	below.•	Do	not	mix	batteries	of	different	types.	Different	types	of	batteries	have	different	characteristics.•	Do	not	mix	old	and	new	batteries.	Mixing	old	and	new	batteries	can	shorten	the	life	of	new	batteries	or	cause	chemical	leakage	in	old	batteries.•	Remove	batteries	as	soon	as	they	have	worn	out.	Chemicals	that	leak	from	batteries	can	cause	a	rash.	If	you	find	any	chemical	leakage,	wipe	thoroughly	with	a	cloth.•	The	batteries	supplied	with	this	product	may	have	a	shorter	life	expectancy	due	to	storage	conditions.•	If	you	will	not	be	using	the	remote	control	unit	for	an	extended	period	of	time,	remove	the	batteries	from	it.•	When	replacing	the	batteries,	use	alkaline	batteries	instead	of	zinc-carbon	ones.
Note on disposing batteriesThe	batteries	provided	contain	no	harmful	materials	such	as	cadmium,	lead	or	mercury.Regulations	concerning	used	batteries	stipulate	that	batteries	may	no	longer	be	thrown	out	with	the	household	rubbish.	Deposit	any	used	batteries	free	of	charge	into	the	designated	collection	containers	set	up	at	commercial	businesses.
Angle of the remote control unit
Use	the	remote	control	unit	by	pointing	it	towards	the	remote	control	sensor.	Objects	between	the	remote	control	unit	and	sensor	may	prevent	proper	operation.
5 m
Remote	control	sensor
Cautions regarding the remote control unit
•	Do	not	expose	the	remote	control	unit	to	shock.	In	addition,	do	not	expose	the	remote	control	unit	to	liquids,	and	do	not	place	in	an	area	with	high	humidity.•	Do	not	install	or	place	the	remote	control	unit	under	direct	sunlight.	The	heat	may	cause	deformation	of	the	unit.•	The	remote	control	unit	may	not	work	properly	if	the	remote	control	sensor	of	the	TV	is	under	direct	sunlight	or	strong	lighting.	In	such	cases,	change	the	angle	of	the	lighting	or	the	TV,	or	operate	the	remote	control	unit	closer	to	the	remote	control	sensor.
Preparation
  
						

							11
Initial installation overview
Follow	the	steps	below	one	by	one	when	using	the	TV	for	the	first	time.	Some	steps	may	not	be	necessary	depending	on	your	TV	installation	and	connection.
Preparation
 nConnect an antenna cable to the antenna terminal (Page 12).
 oIf necessary, insert a CA card into the CI slot to watch scrambled broadcasts (Page 12).
 pPlug the AC cord into the AC outlet (Page 12).
Product	shape	varies	in	some	countries.
Run the initial 
settings
 nCheck that the MAIN POWER switch on the rear of the TV is turned on (;).
•	The	factory	default	for	the	MAIN	POWER	switch	is	set	to	on	(;).
 oTurn on the power using 
						

							12
Before turning on the power


 
21

 nStandard DIN45325 plug (IEC 169-2) 75 q coaxial cable
 oSatellite antenna cable
 pAC cord (product shape varies in some countries)
 qCheck that the MAIN POWER switch on the rear of the TV is turned on (;).
 rCable clamp (bundle the cables with the clamp)
Place	the	TV	close	to	the	AC	outlet,	and	keep	the	power	plug	within	reach.
Inserting the CA card into the CI module
In	order	to	receive	coded	digital	stations,	a	common	interface	module	(CI	module)	and	a	CA	card	must	be	inserted	in	the	CI	slot	of	the	TV.
1 
Carefully	insert	the	CI	module	in	
the	CI	slot	with	the	contact	side	
forward.
2  The	logo	on	the	CI	module	must	
be	facing	outward	from	the	rear	
of	the	TV.
Checking CI module information
Go to “Menu” > “Setup” > “Option” > “CI menu”.•	This	menu	is	only	available	for	digital	stations.•	The	content	of	this	menu	depends	on	the	provider	of	the	CI	module.
Module
General	information	on	CI	module	displays.
Menu Adjustment	parameters	of	each	CA	card	displays.
Enquiry You	can	input	numerical	values	such	as	passwords	here.
NOTE•	It	takes	about	30	seconds	to	certify	the	license	key	when	you	insert	a	CA	card	into	the	CI+	compatible	CI	module	for	the	first	time.	This	process	may	fail	when	there	is	no	antenna	input	or	you	have	never	run	“Auto	installation”.•	The	CI+	compatible	CI	module	sometimes	upgrades	its	firmware.	You	may	not	receive	any	TV	images	before	upgrading.	You	can	only	use	the	power	button	during	upgrading.•	The	CI+	compatible	CI	module	does	not	allow	you	to	output	any	copy	protected	programmes	using	monitor	out.	In	this	case,	the	copy	protect	icon*	is	shown	in	the	programme	information	when	P. INFO	is	pressed.*	Protect	icon:	X•	If	the	TV	displays	an	update	confirmation	message	for	the	CA	card	while	receiving	CI+	compatible	broadcasts,	follow	the	screen	prompts.•	Make	sure	that	the	CI	module	is	properly	inserted.
Quick guide
    
						

							13
Initial auto installation
When	the	TV	is	powered	on	for	the	first	time	after	purchase,	the	initial	auto	installation	wizard	appears.	Follow	the	menus	and	make	the	necessary	settings	one	after	another.
Confirm the following before turning on 
the power
	
E Is	the	antenna	cable	connected?
	
E Is	the	AC	cord	plugged	in?
	
E Is	the	MAIN	POWER	switch	turned	on	(;)?
 1Press 	“View	setting”	>	“Reset”	>	select	“HOME”	again.
 4Setting the country.Press	a/b/c/d	to	select	your	country	or	area,	and	then	press	;.•	This	setting	screen	only	appears	during	the	first	installation.
NOTE•	If	you	set	“Sweden”	in	the	country	setting,	you	can	select	the	cable	provider	“ComHem”.	Refer	to	the	H	mark	in	the	following	steps	or	instructions	about	the	settings	for	“ComHem”.
 5Starting channel search.
Digital search
Analogue search
Skip
Press	a/b	to	select	“Digital	search”,	“Analogue	search”	or	“Skip”,	and	then	press	;.•	To	watch	both	analogue	broadcasts,	digital	broadcasts	and	satellite	broadcasts,	you	should	perform	the	auto	installation	setting	for	each	format	(Page	34).•	If	you	want	to	search	for	more	broadcasts,	execute	“Additional	search”	from	the	“Programme	setup”	menu	(Pages	34_36).•	When	you	select	“Skip”,	only	“Satellite	search”	will	be	performed.	You	should	perform	“Digital	search”	and	“Analogue	search”	from	“Auto	installation”	under	the	“Setup”	menu	if	needed.•	After	performing	“Digital	search”	or	“Analogue	search”,	the	screen	swicthes	to	the	“Satellite	search”	setting.	You	should	then	execute	“Yes”	if	you	want	to	search	for	the	satellite	channels.
NOTE•	If	you	turn	off	the	power	on	the	TV	while	performing	a	channel	search,	the	initial	auto	installation	wizard	will	not	appear.	The	auto	installation	function	allows	you	to	execute	the	installation	again	from	“Setup”	>	“View	setting”	(Page	34).•	The	initial	auto	installation	wizard	will	abort	if	you	leave	the	TV	unattended	for	30	minutes	before	searching	for	channels.•	After	initial	auto	installation	is	completed,	the	default	PIN	is	automatically	set	to	“1234”.	To	change	the	PIN	setting,	refer	to	Password/Lock settings	(Page	 37).	To	clear	 the	PIN	 setting	(PIN	input	will	no	longer	be	needed),	refer	to	CLEARING THE PIN	(Page	59).•	When	“Italy”	is	selected	in	the	country	setting,	the	default	age	restriction	value	is	set	to	18.
Digital broadcast setting
Press c/d to select “Terrestrial” or “Cable”, and then press ;.
TerrestrialCable
H•	When	you	set	“Sweden”	in	the	country	setting	and	select	“Cable”	for	the	searching	format,	you	can	select	the	cable	provider	“ComHem”.
 ESearching for terrestrial broadcasts
The TV searches for, sorts and stores all the receivable TV stations according to their settings and the connected antenna.•	To	abort	the	initial	auto	installation	in	progress,	press	6.
After searching for DVB-T channels, the screen switches to the “Satellite search” setting (Page 15).
Quick guide
  
						

							14
Quick guide
 ESearching for cable broadcasts
To change each item to the appropriate settings:	1Press	a/b	to	select	the	menu,	and	then	press	;.
Scrambled stations[Yes]
Search method[Channel]
Start frequency
Network ID [None]
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Reset
Search start
	2Press	a/b/c/d	or	0_9	to	select	or	input	the	appropriate	item/value,	and	then	press	;.	3Press	a/b	to	select	“Search	start”,	and	then	press	;.	4Press	c/d	to	select	“Yes”	to	start	searching	cable	broadcasts,	and	then	press	;.	5The	TV	searches	for,	sorts	and	stores	all	the	receivable	TV	stations	according	to	their	settings	and	the	connected	antenna.•	To	abort	the	initial	auto	installation	in	progress,	press	6.
After searching for DVB-C channels, the screen switches to the “Satellite search” setting (Page 15).
H•	The	“Scrambled	stations”	menu	and	the	“Search	method”	menu	are	not	displayed	on	the	screen	as	each	menu	item	is	fixed.•	The	value	of	“Start	frequency”	and	“Network	ID”	should	be	set	to	the	value	specified	by	the	cable	provider.
MenuDescription Selectable items
Scrambled 
stations Specifies
	ISet	up	“Symbol	rate	2”	if	the	cable	provider	uses	several	symbol	rates.	JWhen	“Quick”	is	selected,	“Scrambled	stations”	is	automatically	set	to	“No”.	JWhen	“Quick”	is	selected,	“None”	for	the	“Network	ID”	menu	cannot	be	selected.
H•	When	you	set	“Sweden”	in	the	country	setting	and	select	“Cable”	for	the	searching	format,	you	can	select	the	cable	provider	“ComHem”.	Follow	the	screen	prompts.
Analogue broadcast setting
The TV searches for, sorts and stores all the receivable TV stations according to their settings and the connected antenna.•	To	abort	the	initial	auto	installation	in	progress,	press	6.
After searching for analogue channels, the screen switches to the “Satellite search” setting (Page 15).
  
						

							15
Searching for satellite broadcasts
Press	c/d	to	select	“Yes”,	and	then	press	;.
YesNo
•	If	you	do	not	perform	“Satellite	search”	setting,	select	“No”,	and	then	press	;.•	The	current	DVB-S/S2	setting	screen	is	displayed.
Next
other
SatelliteLNB Frequency
Low High
Satellite System
Max. 4 satellites on DiSEqC multiswitch
Change setting
•	You	must	first	complete	“Change	setting”	before	moving	to	the	“Next”	setting.
 1When starting the satellite search after setting the scrambled stations:
Press c/d to select “Next”, and then press ;.
NOTE•	When	you	perform	the	initial	auto	installation,	“Next”	cannot	be	selected.	Completing	“Change	setting”	enables	you	to	select	“Next”.
Start search
other
SatelliteSymbol rate 1 Symbol rate 2
Scrambled stations: No
Change setting
 EStart search:DVB-S/S2	channel	searching.
 1Press c/d to select “Start search”, and then press ;.
 2The TV searches for and stores all the receivable TV stations according to their settings and the connected antenna.•	Select	“Yes”	to	sort	the	search	result	in	alphabetical	order.•	To	abort	the	initial	auto	installation	in	progress,	press	6.
 EChange setting:
 1Press c/d to select “Change setting”, and then press ;.•	The	setting	screen	of	“Scrambled	stations”	and	“Symbol	rate”	is	displayed.
Scrambled stations [No]
Search start
SAT1-Symbol rate 1
SAT1-Symbol rate 2
SAT2-Symbol rate 1
YesNo
 2Press a/b to select “Scrambled stations”, and then press ;.•	Scrambled	stations:	Specifies	if	you	need	to	add	pay-TV	services.
 3Press c/d to select “Yes”, and then press ;.
 4Press a/b to select the symbol rate you want to modify, and then press ;.•	Symbol	rate:	You	need	to	set	each	symbol	rate	of	all	the	satellite	broadcasts	that	the	TV	can	receive	(eight	is	the	maximum	number	of	symbol	rates	that	can	be	displayed).
 5Press c/d to select “Search start”, and then press ;.
 6The TV searches for and stores all the receivable TV stations according to their settings and the connected antenna.•	Select	“Yes”	to	sort	the	search	result	in	alphabetical	order.•	To	abort	the	initial	auto	installation	in	progress,	press	6.
Quick guide
  
						

							16
 2When you change the antenna connection setting:
Press c/d to select “Change setting” on the DVB-S/S2 setting screen in the left column, and then press ;.•	The	antenna	connection	setting	screen	is	displayed.
Single satellite
2 satellites on 22kHz switchbox
2 satellites on toneburst switchbox
Max. 4 satellites on DiSEqC multiswitch
Communal satellite system
NOTE•	You	can	select	the	antenna	connection	method	from	the	five	types.	Consult	your	dealers	before	using	a	method	other	than	“Single	satellite”.
 E“Single satellite” setting
 1Press a/b to select “Single satellite”, and then press ;.
 2Press a/b to select “SAT1 [None]” to display the satellite broadcasts that the TV can receive, and then press ;.
SAT1 [None]
Next
 3Press a/b/c/d to select your favorite satellite, and then press ;.•	You	cannot	select	“Next”	unless	you	set	the	satellite	broadcast	in	step	3.
Euro Bird 1
Atlantic Bird 1
 4Press a/b to select “Next”, and then press ;.
SAT1 [ASTRA 1]
Next
 5Press c/d to select “Yes (0/22kHz)” or “No” to set the LNB frequency, and then press ;.
Yes (0/22kHz)No
 6Press a/b to select the item and press c/d to adjust 9,000 MHz to 12,000 MHz to the appropriate value.
EXAMPLE
SAT1 low
SAT1 high
OK
 7Press a/b to select “OK”, and then press ;.
After completing this setting, the screen switches to the DVB-S/S2 setting screen shown in the left column on page 15.
NOTE•	Follow	the	instructions	on	the	screen	for	“2	satellites	on	22kHz	switchbox”,	“2	satellites	on	toneburst	switchbox”,	“Max.	4	satellites	on	DiSEqC	multiswitch”	and	“Communal	satellite	system”	settings.•	To	set	multiple	satellite	channels,	go	to	“Max.	4	satellites	on	DiSEqC	multiswitch”.
Quick guide
  
						

							17
Quick guide
Checking signal strength and 
channel strength (DVB-T/C/S/S2)
If	you	install	a	DVB-T/C/S/S2	antenna	for	the	first	time	or	relocate	it,	you	should	adjust	the	alignment	of	the	antenna	to	receive	a	good	reception	while	checking	the	antenna	setup	screen.
 1Go to “Menu” > “Setup” > “View setting” > “Channel settings” > “Antenna setup-DIGITAL”.
 2Press a/b to select “Digital setup” or “Satellite setup”, and then press ;.
 EChecking signal strength
 3Press a/b to select “Signal strength”, and then press ;.
Signal strength for DVB-T/C
Supply voltageCH No.
CurrentMax.
Signal strengthSignal strength
Channel strength
CurrentMax.
Quality
Signal strength for DVB-S/S2
CurrentMax.
Signal strength
Signal strength
Channel strength
CurrentMax.
Quality
 EChecking channel strength
 4Press a/b to select “Channel strength”, and then press ;.•	You	can	input	a	specified	frequency	band	using	the	0_9	numeric	buttons.
Channel strength of DVB-T
Supply voltage
CH No.
CurrentMax.
Signal strengthMHz
Signal strength
Frequency
Channel strength
CurrentMax.
Quality
Channel strength of DVB-C
Supply voltage
Current
Max.
Signal strengthMHz
Signal strength
FrequencySymbol rateQAM modulationChannel strength
CurrentMax.
Quality
Channel strength of DVB-S/S2
CurrentMax.
Signal strengthMHz
Signal strength
Frequency
Symbol rateBand
Channel strength
CurrentMax.
Quality
Vert/Low
 5Position and align the antenna so that the maximum possible values for “Signal strength” and “Quality” are obtained.
NOTE•	The	values	of	“Signal	strength”	and	“Quality”	indicate	when	to	check	the	appropriate	alignment	of	the	antenna.
Supplying power to the antenna
You	must	supply	power	to	the	antenna	in	order	to	receive	digitally/terrestrially	broadcast	stations	or	satellite	broadcast	stations	after	connecting	the	antenna	cable	to	the	antenna	terminal	on	the	
rear	of	the	TV.
1 Press	@	and	the	“Menu”	screen	displays.2 Press	c/d	to	select	“Setup”,	and	then	press	;.3 Press	c/d	to	select	“View	setting”,	and	then	press	;.4 Press	a/b	to	select	“Channel	settings”,	and	then	press	;.5 Press	a/b	to	select	“Antenna	setup-DIGITAL”,	and	then	press	;.6 Press	a/b	to	select	“Supply	voltage”,	and	then	press	;.7 Press	c/d	to	select	“On”,	and	then	press	;.
Downloaded From TV-Manual.com Manual•  
						

							18
Daily operation
Switching on/off
Turning on/off the power
 1Turn on (;) the MAIN POWER switch on the rear of the TV (Page 5).
 2To turn on the TV, press a on the remote control unit.
 3To turn off the TV, press a on the remote control unit.
 4Turn off (a) the MAIN POWER switch on the rear of the TV (Page 5).•	When	turning	off	the	power	using	the	MAIN	POWER	switch	on	the	rear	of	the	TV,	EPG	data	will	be	lost.
Standby mode
 ETo standby modeIf	the	MAIN	POWER	switch	on	the	rear	of	the	TV	is	turn	on	(;),	you	can	switch	it	to	standby	by	pressing	a	on	 the	 remote	 control	unit.
 ESwitching on from standbyFrom	standby,	press	a	on	the	remote	control	unit.
NOTE•	If	you	are	not	going	to	use	this	TV	for	a	long	period	of	time,	be	sure	to	remove	the	AC	cord	from	the	AC	outlet	or	turn	off	(a)	the	MAIN	POWER	switch	on	the	rear	of	the	TV	(Page	5).•	A	small	amount	of	electric	power	is	still	consumed	even	when	the	MAIN	POWER	switch	is	turned	off	(a)	(Page	5).
Switching between digital, 
satellite and analogue broadcasts
Watching digital 
broadcasts Watching analogue 
broadcasts
Watching satellite 
broadcasts
NOTE•	If	a	number	of	satellite	channels	are	set,	each	time	you	press	the	SAT	button	the	channel	switches	as	follows.
SAT1
SAT2
SAT3
SAT4
Changing channels
With :r/s With 0_9
Watching TV