Sharp Lc 46le810 Operation Manual

							 49
■ PC control of the TV Attach an RS-232C cable cross-type (commercially 
available) to the supplied Din/D-Sub RS-232C for the 
connections.
This operation system should be used by a person who is 
accustomed to using computers.
■  Communication conditionsSet the RS-232C communication settings on the PC to 
match the TVs communication conditions.
The TVs communication settings are as follows:
Baud rate:
9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
■ Communication procedure Send the control commands from the PC via the RS-
232C connector.
The TV operates according to the received command 
and sends a response message to the PC.
Do not send multiple commands at the same time. 
Wait until the PC receives the OK response before 
sending the next command.

■ 
Command format
Eight ASCII codes 
e CR
Command 4-digits Parameter 4-digitsReturn code
C1 C2 C3 C4 P1  P2  P3  P4
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0–9, x, blank, ?
■ 
ParameterInput the parameter values, aligning left, and  ll with 
blank(s) for the remainder. (Be sure that 4 values are 
input for the parameter.)
When the input parameter is not within an adjustable 
range, “ERR” returns. (Refer to “Response code format”.)
Any numerical value can replace the “x” on the table.
a
30
0009 0???? ?
When “?” is input for some 
commands, the 
present setting 
value responds.
■ 
Response code format
Normal response
Return code (0DH) Return code (0DH)
Problem response (communication 
error or incorrect command)
OKERR
■ 
Command table Commands not indicated here are not guaranteed to operate.CONTROL ITEM COMMANDPARAMETERCONTROL CONTENTS
POWER ON COMMAND SETTING
POWER SETTING The Power On command rejected.
It input-switches by the toggle. (It is the same as an input change key\
)
It input-switches to TV. (A channel remains as it is. (Last memory))
It input-switches to INPUT1~INPUT7.
Although it can choose now, it is toggle operation in inside.
The screen position variable ranges depend on the View Mode or the 
signal type. The ranges can be seen on the position-setting screen.
0: Although it can choose now, it is toggle operation in inside.
1: Only available when 4:3 signal is being input.
5, 6: Only available when 4:3 signal is being input.
8: [PC] Available except when UXGA is being input. 
    [AV] Only available when 1080i/p is being input.
9: Only available when 720p is being input.
(Toggle)
Input terminal number (1–7)
0: (Toggle), 1:  STANDARD, 2: MOVIE, 3: GAME, 
4: USER, 5: DYNAMIC (Fixed), 6: DYNAMIC, 7: PC, 
8: x.v. Color, 100: AUTO
Volume (0–60)
Only PC mode. (0–180)
Only PC mode. (0–40)
0: (Toggle) [AV], 1: Side Bar [AV], 2: S.Stretch [AV]
3: Zoom [AV], 4: Stretch [AV], 5: Normal [PC]
6: Zoom [PC], 7: Stretch [PC], 
8: Dot by Dot [PC] [AV], 9: Full Screen [AV]
10: Auto [Netix], 11: Original [Netix]
   
An input change is included if it is not TV display.
In Air, 2–69ch is effective.
In Cable, 1–135ch is effective.
If it is not TV display, it will input-switch to TV. (same function as CH U)
If it is not TV display, it will input-switch to TV. (same function as CH V)
Toggle operation of a closed caption.
0: (Toggle), 1: On, 2: Off
0: Off, 1: OFF TIMER – 30 MIN., 2: OFF TIMER – 60 MIN., 
3: OFF TIMER – 90 MIN., 4: OFF TIMER – 120 MIN.
The channel number of TV
The channel number of TV +1
The channel number of TV  –1(Toggle) (1–135)
RSPW
ITGD
ITVD
IAVD
INPUT SELECTION TOGGLE
AV MODE SELECTION
VOLUME
POSITION
VIEW MODE
SURROUND
SLEEP TIMER
CHANNEL
CC DIRECT
(ANALOG)
(DIGITAL)
CH UP
CH DOWN CHANNEL H-POSITION H-POSITION
V-POSITION
CLOCK
PHASE
AVMD
VOLM
HPOS
VPOS
CLCK
PHS E
ACSU
OF TM DCCH
CHUP
CHDW
CLCP
WI DE
0
x
0
*
*
*
*
*
*
*
*
*
*
x
x
x *
*
_
_
_ _
_ _ *
*
*
*
*
_
_
_
_
_
*
_
_
_ _
_ _ *
*
*
*
_ _
_
_
_
_
_ DIGITAL Air (Two-Part numbers, 2-digit plus 2-digit)
(0100-9999)
(1-999)
(0-999)
(0-9999)
(0-6383) DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit) Front half of DIGITAL CABLE CHANNEL NO. (Designate major channel)
Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)
DIRECT
CHANNEL
DA 2 P * * * *
DC 2 U * * * _
DC 2 L * * * _
DIGITAL Cable (One-Part numbers, 5-digit, less than 10,000)
DC 1 0 * * * *
DIGITAL Cable (One-Part numbers, 5-digit, more than 10,000)
DC 1 1 * * * *
_
_
_ _
(Toggle)
AUDIO SELECTION
ACHA x _ _ _
_0: (Toggle), 1: On, 2: Off
MUTE
MU T E * _ _ __ _
_
_
_ _ _Off
The Power On command accepted.
1___On
Power On
1 _ _ _ Power On It shifts to standby.
P O W R 0 _ _ _ Power Off
_
_
_
_
TV
INPUT1-7
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears, enter a value in the range indicated in br\
ackets under CONTROL CONTENTS.
Any numerical value can replace the “x” on the table.



RS-232C Port Specifi
 cations
Using a PC
-$  @ @ @ -&  6 / @& J O EC 


 -$@@@-&6/@&JOEC


  


   



 
						

							 50
Up to four devices can be connected to the HN-VA400U 
adapter.
Model number Number of portsHN-VA401SU 4  +
1
HN-VA400U 4
HN-VA100U 1
Internet
Using the Internet
By connecting your TV to a broadband system, you can access the Internet\
 from the TV.
Display the “Sidebar Widget” on the screen to check out the latest\
 Internet information and access a range of 
useful information for AQUOS users from the original home page*.
About the original home page The original home page is a website set up speci cally for AQUOS owners. 
The website is worth visiting as it provides a range of useful informati\
on, including tips on using your AQUOS 
and a frequently asked questions section.
Internet Setup
H Connecting to the InternetTo connect your TV to the Internet, you must have a broadband Internet c\
onnection.
Use an ETHERNET cable (commercially available) to connect the ETHERNET\
 terminal on the TV to your 
broadband router (commercially available).
If you do not have a broadband Internet connection, consult the store wh\
ere you purchased your TV or ask your 
Internet service provider or telephone company.
ETHERNET cable
(commercially available)
Internet
H Checking your Internet connection
Press  AQUOS  NET  twice or three times to switch to the TV+Web or Web screen. 
When the original home page appears, now you are connected to the Intern\
et.
If you have failed to connect to the Internet in the above operation, th\
en an 
error message will appear. In this case, press  EXIT to return to the normal TV 
screen and check the relevant settings (see page 51).
If you still cannot connect to the Internet, please consult your Interne\
t service 
provider or telephone company.
H Information on the PLC adapter


*








The SHARP PLC adapter kit (sold separately) lets you 
use the existing electrical wiring in your house to create 
a home network.
*1 
Simply plug the adapters into electrical outlets at the 
desired locations, and then connect your computer 
and other devices to the adapters with LAN cables (two 
LAN cables are provided).
If you have Broadband Internet service, connect your 
router to one of the adapters to allow all your network 
devices to access the Internet.
Data can be exchanged at speeds of up to 85 Mbps
*2 
on your network.
*1:  PLC does not have router function. To connect  to the Internet via network, Broadband Internet 
connection and related devices such as router etc 
is required.
*2:  The actual communication speed may be affected  by power line conditions, other electrical appliances 
and network conditions.
-$  @ @ @ -&  6 / @& J O EC 


 -$@@@-&6/@&JOEC


  


   



 
						

							 51
Using the Internet
 
H If you cannot connect to the Internet
Perform the procedures below to check your TVs 
network settings.
Ethernet Setup
1 Press  EXIT to display the normal TV screen.
2 Press  MENU  to display the MENU screen, and then 
press  c/
d  to select “Initial Setup”.
3 Press 
a/
b  to select “Internet Setting”, and then 
press  ENTER .
4 Press 
a/
b  to select “Communication Setup”, and 
then press  ENTER.
5 Press 
a/
b  to select “Ethernet Setup”, and then 
press  ENTER .
Check that numbers are displayed for each setting.
If there are any settings without numbers, specify the 
numbers by following the on-screen instructions.
For information on how to enter text, see page 52.
6 Press MENU  to exit.
Setting the Zip Code
1 Repeat steps 1 to 4 in  Ethernet Setup.
2 Press 
a/
b  to select “Zip Code”, and then press 
ENTER . After “Change” is highlighted, press 
ENTER  again.
3 Press 
c/
d  to select “US/Mexico” or “Canada”, 
and then press  ENTER.
4 Enter your zip code.The U.S. and Mexico use 5-digit zip codes. Canada 
uses 6-digit codes.
For the U.S. and Mexico, use  0-9  on the remote 
control unit to enter your zip code. For Canada, use 
the software keyboard.
5 After “Complete” is highlighted, press  ENTER.
6 Press MENU  to exit.
Interactive Service
If you do not want other people to connect to the 
Internet in your absence, you can make settings to 
keep the TV away from the Internet.
1 Press MENU  to display the MENU screen, and then 
press  c/
d  to select “Initial Setup”.
2 Press 
a/
b  to select “Internet Setting”, and then 
press  ENTER .
3 Press 
a/
b  to select “Interactive Service”, and then 
press  ENTER .
Input the 4-digit secret number by using  0–9 .
4 Press 
c/
d  to select “No”, and then press 
ENTER.
If you want to allow Internet connection, select “Yes”, 
and then press ENTER.
5 Press MENU  to exit.







Displaying Updated Information and 
Support Service
This function can be used to display up-to-date 
information on the Sidebar Widget via the Internet and 
allow you to receive support service over the network.
Sidebar Widget
1 Press AQUOS  NET  repeatedly  to display the 
Sidebar Widget.
Each time you press  AQUOS NET , the screen image 
toggles as shown below:
Sidebar Widget      TV+Web      Web      TV
When you are not connected to the Internet, a network 
function explanation screen is displayed.
The services displayed vary depending on 
circumstances.
2 Press  a/
b  to select a title, and then press 
ENTER .
The web page for the selected title is displayed.
The service details vary depending on circumstances.
3 Press EXIT to return to the normal TV screen.
If you start up the Sidebar Widget while a Closed Caption 
is displayed, the Closed Caption is automatically hidden.
Web page appearances may differ depending on the type 
of screen (TV+Web or Web).
When a still image is displayed, the Sidebar Widget does 
not appear even if you press  AQUOS NET .
When displaying TV+Web with a channel in which the 
V-Chip is enabled, the cursor keys on the remote control 
unit do not function.
AQUOS Advantage Live
1 Press  DOCK  to display the DOCK.
2 Press 
c/
d to select “AQUOS ADVANTAGE LIVE”, 
and then press  ENTER.
3 Press 
a/
b /
c /
d  to select the desired service.My Account:
 Register your AQUOS LCD today and 
receive a free 3 month warranty extension! Use 
this service to complete registration, view user and 
warranty information.
Live Support:  Connect to Sharp service center over 
the internet to receive remote assistance for AQUOS. 
Sharp advisors will remotely connect to AQUOS 
and can provide variety of services such as setup, 
performance diagnostic, etc. You must agree to the 
terms and conditions when using Live Support.
Mail Center: 
Stay connected with SHARP news and more!Learn More:  Learn more about the many bene ts of 
AQUOS Advantage membership available to you.
New Software: 
Stay up to date with the latest AQUOS 
LCD TV software.
User Guide:  In depth AQUOS operating instructions for 
your AQUOS LCD TV.
4 Press  EXIT to return to the normal TV screen.
The display may change as a result of a software update.








- $  @ @ @ -&  6 / @& J O EC 


 -$@@@-&6/@&JOEC


  


   



 
						

							 52
Entering Text (Software Keyboard)
When you are editing an input screen or specifying the 
Ethernet settings used for accessing the Internet, enter 
text from the software keyboard.
You can enter up to 128 characters for text.

Buttons Description
a Moves the focus up. When the focus is at the top edge, this moves the fo\
cus to 
the opposite edge (bottom edge). 
b Moves the focus down. When the focus is at the bottom edge, this moves t\
he 
focus to the opposite edge (top edge). 
c Moves the focus left. When the focus is at the left edge, this moves the\
 focus to 
the opposite edge (right edge).
When the focus is on “Character Set”, this selects the character t\
ype (moving 
backwards).
When the focus is in an input box, this moves the cursor in the input bo\
x to the left. 
d Moves the focus right. When the focus is at the right edge, this moves t\
he focus to 
the opposite edge (left edge).
When the focus is on “Character Set”, this selects the character t\
ype (moving 
forwards). 
When the focus is in an input box, this moves the cursor in the input bo\
x to the 
right. 
ENTER Performs the processing for the button currently in the focus. 
EXIT Closes the software keyboard without applying the original input element\
s for the 
entered text.
Erases the text in the input box where the cursor is currently located. \
RETURN When the cursor is at the end of a sentence, this acts as a backspace. 
0-9 Directly enters the single-byte number for that button.
A (red) Directly enters prediction candidate 1. 
B (green) Directly enters prediction candidate 2.
C (blue) Directly enters prediction candidate 3.
D (yellow) Enters a space. 
Caps Off/Caps On /Caps Lock
If “alphabet” is selected in “Character Set”, this switches \
characters between uppercase and lowercase.
Each time you press  ENTER, the character type switches as 
shown below:
Caps Off: all the characters are lowercased
Caps On: only the  rst character is uppercased
Caps Lock: all the characters are uppercased
Done
Applies the entered information and closes the software 
keyboard.
Quit
Closes the software keyboard without applying the entered 
information. You can also close the software keyboard by pressing 
EXIT  on the remote control unit.
Displays the icon “”, indicating that a new line has been 
inserted.
Clear
Erases the character string.
When the cursor is somewhere in a line: the character 
string to the right of the cursor will be erased.
When the cursor is at the right end of a line: the entire line 
will be erased.
Delete
If the cursor is at the right end of a line, this erases text one 
character at a time. You can also delete text by pressing  RETURN on the 
remote control unit.




Using the Internet
The text you enter is displayed as you type it in. 
To move the cursor (the current input position), use 
“
” or “” on the software keyboard.
Press 
c/
d  to select the type of characters entered: 
alphabet, number or sign.
(The selectable types depend on the input source.)
While you are entering text, likely input conversion candidates 
are displayed based on what you typed in. You can also enter text by pressing  A, B  or  C on the remote 
control unit.
 Enters a space.
-
$  @ @ @ -&  6 / @& J O EC 


 -$@@@-&6/@&JOEC


  


   



 
						

							 53
Using the Browser
ENTER, 
a /
b /
c /
da /
b /
c /
d to select a link that you want to jump, 
and then press  ENTER.
EXIT Press the button to return to the TV screen.
RETURN Press the button to return to the previous page.
Example : The image shown below, which is only for  explanation, is subject to change.
About linksWeb pages on the Internet often include “links” that 
allow you to jump to other web pages (or sites).
“Links” can take various forms, including words 
or images, but they always work in the same way 
letting you jump to the link destination when you 
select them.
Selected items (such as links of text input  elds) are 
enclosed in a yellow frame.
You can jump from a “link” to the corresponding link 
destination.
CAUTION
If the power is cut due to a power failure or the TV being 
unplugged while you are using the Internet, information 
such as bookmarks or cookies may not be saved correctly.
When a security noti cation window is displayed:
Press 
ENTER to close the window.
This window appears when you visit a web page that has 
security protection, or when you move from a protected 
page to an unprotected page.
In “Security Settings” you can set whether or not this 
window is displayed. (See page 56.)
When a cookie con rmation window appears:
Choose whether or not to accept the cookie (see page 56), 
and then press 
ENTER.
In “Cookies” settings you can set whether or not this 
window is displayed. You can also opt to delete all the 
cookies at once. (See page 56.)
To users who access the Internet from a PC When you access the Internet from this TV, the 
procedures may not be the same as regular 
browser-based access on a PC.
You cannot download  les.
You cannot view a history of the pages you have 
visited.
You cannot change the startup page displayed 
when you press  AQUOS NET .
Pop-up windows appear in separate tabs.
On some pages, video and audio cannot be 
played, and text or images may not be displayed 
correctly.















When “z” is displayed in a page:The page failed to load successfully, or it contains images 
with formats that cannot be displayed on the TV. Try 
reloading the page by selecting “
” (see page 54) in the 
toolbar.

Using the Internet
Photo PlayerP
hoto  P la ye r
:Tool:T ool:Scroll:S cro llAQUOSA Q UO S   C on sole
Click   this  bu t t on  to  go   to  AQUOS  Network.
Page  1
       o f  3Add WidgetsA dd W id gets
LegalL eg al
AQUOSA Q UO S C en te rAQUOSA Q UO S  Network N etw orkWhat’s NewW ha t’s  N ew
Feae atured Cure d Co n te n t
SportsS ports
EntertainmentE nte rta in m ent
A Q UO S Gallerya ll e ry
CONSOLE
MondayM ond ayTodayT oda yWednesdayW edn esd a yTuesdayT uesd a y
AQUARIUSA Q UAR IU SGEMINIG EM IN IPISCESPIS C ESARIESAR IE S
D
Pages with security protection are 
clearly shown as such.
If content on a page is continued on another page, 
directions to that page are shown clearly.
You can use  a/
b /
c /
d  to go to the continuation of a 
page. Where there is link text or a link image in the 
direction pressed, the text or image is selected  rst. 
If this happens, press the same direction button 
several times.

Tab
-
$  @ @ @ -&  6 / @& J O EC 


 -$@@@-&6/@&JOEC


  


   



 
						

							 54
Using the Toolbar
You can use the toolbar to control the browser and to 
specify settings.
1 Press D on the remote control unit to display the 
toolbar.
2 Press  c/
d  to select a function, and then press 
ENTER .
Selected item Description
Displays the linked page in a new tab.
Displays the Tab menu.
Returns to the previous page.
Goes back to the original page when you 
have viewed the previous page.
Refreshes the page.
Interrupts a page while it is loading.
Displays the original home page.
Select this to open a bookmark.
Adds the current page to your bookmarks.
Displays the Browser menu.
Using Tabs
You can use tabs to view up to 3 web pages at the 
same time. Each page appears in a separate tab, and 
you can switch between the tabs.
1 Press B on the remote control unit to display the 
Tab menu.
You can also display the Tab menu by clicking “” in 
the toolbar.
Selected item Description
Select This Displays the web page in the 
selected tab.
Close This Tab Closes the selected tab.
You can also press  C on the 
remote control unit to close a 
tab.

Close Other Tabs Closes the other (unselected) tabs.
Create New Tab Creates a new tab.
You can also press  A on the 
remote control unit to create a 
tab.

2 Press 
c/
d  to select a tab.
3 Press 
a/
b  to select the item you want to use, and 
then press  ENTER.

Using the Internet
-$  @ @ @ -&  6 / @& J O EC 


 -$@@@-&6/@&JOEC


  


   



 
						

							 55
Saving the URL of the Current Page
Adding a web page to your bookmarks allows you to 
return to that page later by simply selecting it from your 
list of bookmarks.
1 Display the page that you want to bookmark.
2 Press D on the remote control unit to display the 
toolbar.
3 Press  c/
d  to select  “”
 in the toolbar, and then 
press  ENTER .
4 Select “Yes”, and then press  ENTER.
The page is added to your bookmarks.
Opening a Bookmarked Page
1 Press D on the remote control unit to display the 
toolbar.
2 Press  c/
d  to select  “”
 in the toolbar, and then 
press  ENTER .
Your bookmarks list is displayed.
3 Press 
a/
b /
c /
d  to select the page you want to 
access, and then press  ENTER.
The selected page is displayed.
If you have bookmarked 11 or more web pages, press 
c/
d  to scroll through your bookmarks list. 
When opening a bookmark in a new tab:
1
 Press 
A instead of  ENTER. The Bookmarks menu appears.
2 Select “Open in New Tab”, and then press 
ENTER .





Editing Bookmarks
You can rearrange or delete the  bookmarks.Switching between the URL and title name
1 Press  D on the remote control unit to display the 
toolbar.
2 Press  c/
d  to select  “”
 in the toolbar, and then 
press  ENTER . 
Your bookmarks list is displayed.
3 Press 
a/
b  to select the title you want to edit from 
the bookmarks list, and then press  A on the remote 
control unit.
The Bookmarks menu appears.
4 Select “Display by Address” or “Display by Title” in 
the Bookmarks menu, and then press  ENTER.
Rearranging displayed items
1 Press  D on the remote control unit to display the 
toolbar.
2 Press  c/
d  to select  “”
 in the toolbar, and then 
press  ENTER .
Your bookmarks list is displayed.
3 Press 
a/
b  to select the title you want to display 
in a different position from the bookmarks list, and 
then press  A on the remote control unit.
The Bookmarks menu appears.
4 Press 
a/
b  to select “Move Up” or “Move Down”, 
and then press  ENTER.
Deleting bookmarks
1 Press  D on the remote control unit to display the 
toolbar.
2 Press  c/
d  to select  “”
 in the toolbar, and then 
press  ENTER .
Your bookmarks list is displayed.
3 Press 
a/
b  to select the title you want to delete, 
and then press  A on the remote control unit.
The Bookmarks menu appears.
4 Press 
a/
b  to select “Delete”, and then press 
ENTER .
To delete all the bookmarks, select “Delete All”.
5 Press 
c/
d  to select “Yes”, and then press 
ENTER .
■


■


■



Using the Internet
-
$  @ @ @ -&  6 / @& J O EC 


 -$@@@-&6/@&JOEC


  


   



 
						

							 56
Browser Settings
You can check or modify your browser settings from 
the Browser menu. 
The Browser menu includes a display settings menu 
and a security settings menu.
1 Press D to display the toolbar.
2 Press 
c/
d  to select  “”
 in the toolbar, and then 
press  ENTER .
3 Press 
c/
d  to select the settings menu you want to 
access.
4 Press  a/
b  to select and con rm the item you want 
to set.
5 Press  a/
b /
c /
d  to specify the required setting, 
and then press  ENTER.
6 Press D to exit.
View Settings
Zoom In/Out: Zoom in:  Displays content enlarged to 200%.
Normal:  Displays content at 100%.
Zoom out:  Displays content reduced to 75%.
Encoding:  Selects the desired encoding from the list below:
Western (ISO-8859-1)/Unicode (UTF-8)
Page Information:  Displays information about the currently 
displayed page.
Reset: Yes:  Resets the browser settings.
No:  Does not reset the browser settings.
“Reset” does not reset the certi cation enable/disable and 
Encoding settings.

Security Settings
Security:
Save Setting:  If you select this option, a message is 
displayed when you move from a protected page to an 
unprotected page.
To change this setting, remove the tick, select “Save 
Setting” and then press  ENTER.
Root Certifi  cates/CA Certifi  cates: Displays the list of 
certi cates. To disable a certi cate, select the certi cate 
to be disabled and press  A to display the sub-menu. 
Select “Disable”, and then press  ENTER.
Disabled certi cates are shown unticked in the 
certi cate list screen.
Cookies: Accept all:  Select this option to accept all cookies.
Reject all:  Select this option when you do not want to 
accept cookies.
Prompt before accepting:  When you open a page 
that uses cookies, this option displays a con rmation 
message.
Delete All Cookies:  Deletes all your cookies.
Server Certifi  cates: Displays certi cates for the connected 
server.
Browser Information:  Displays browser information.
• This product contains NetFront Browser of 
ACCESS CO., LTD.
• ACCESS, the ACCESS logo and NetFront are registered trademarks or trademarks of 
ACCESS CO., LTD. in the United States, 
Japan and/or other countries.
  © 2009 ACCESS CO., LTD. All rights  reserved.
• This software is based in part on the work of the Independent JPEG Group.

Using the Internet
- $  @ @ @ -&  6 / @& J O EC 


 -$@@@-&6/@&JOEC


  


   



 
						

							 57
Using the Internet
Instantly Watching Movies from Netfl ix
Please check that the most current software is 
loaded on TV by selecting Auto Update Setting on 
Software Update (see page 34) or by visiting 
http://www.sharpusa.com/products/support/ 
to check for a download of the newest software version.
This function allows you to enjoy Net ix through the 
Internet.
Net ix is an online DVD and Blu-ray Disc rental service, 
offering rental-by mail and streaming instantly to Net ix 
members.
To enjoy this function, make a broadband Internet 
connection to both your PC and the TV (see page 50), and 
then set Internet Setting (see page 51), then perform the 
following operation.
The quality depends on the network speed and original bit 
rate.
For more information on Net ix visit http://www.net ix.com/
help or login to your Net ix account and click Help at the 
top of the page.
Net ix is only available in the U.S.
Illustrations are examples and may differ from the actual 
Net ix screens. The display and operations may change as 
a result of a software update.
Use Net ix without con guring a proxy server. Part or all of 
Net ix may not be available when connecting to the Internet 
via a proxy server.
When Net ix is used, “Position” does not work.
Settings for Watching Netfl ix Content on the TV
 
1 Press DOCK  to display the DOCK.
2 Press 
c/
d  to select NETFLIX, and then press 
ENTER .
3 Read the Disclaimer displayed on the screen. If 
you agree, press 
a/
b  on the last page to select 
Agree, and then press  ENTER.
  (If you do not agree, this service cannot be used.)







4 Obtain the Net ix activation code.
H If you do not have a Netfl  ix account
1  Press 
a/
b  to select no-start my FREE trial, 
and then press  ENTER.
The screen of the TV
2
 Subscribe by visiting http://www.net ix.com/sharp 
from your PC.
3 Press  a/
b  to select I’m now a member, and 
then press  ENTER.
The screen of the TV
H If you have a Netfl  ix account
Press  a/
b  to select yes-activate instant streaming 
from Net ix, and then press  ENTER.
The screen of the TV
5 You will see the following window.
The activation code is displayed.
The screen of the TV
-$  @ @ @ -&  6 / @& J O EC 


 -$@@@-&6/@&JOEC


  


   



 
						

							 58
6 Using your PC, visit http://www.netfl ix.com/activate, 
and then enter the activation code displayed in step 5.
The screen of the PC
After a period of time, the TV will be activated, and the 
empty instant Queue screen will be displayed.
Adding Content to the Instant Queue
7  To add a movie to the instant Queue of the TV, select the Add to Instant button on Netfl ix Watch 
Instantly web page using your PC.
After a period of time, the instant Queue registered 
using your PC will appear on the TV screen.
Playing Back Content in the Instant Queue on the TV
8 Press  c/
d  to select the desired title, and then 
press  ENTER .
When registration and set-up are completed, you can 
jump from the DOCK to the instant Queue screen.
(See steps 1 to 2 in  Settings for Watching Netfl  ix 
Content on the TV .)
The screen of the TV
When there are more than one title in the instant 
Queue, press τ/κ to scroll through several 
thumbnails so you can perform a quicker search.
The parental control settings on the TV (see pages 32 
to 33) do not apply to Netfl ix. To adjust the parental 
controls for your instant Queue, go to Netfl ix.com/
YourAccount.
The time required to display the instant Queue screen 
varies depending on the Internet connection status and 
the number of titles in the instant Queue.
•
•
•
•
•
•
9  The title you selected is displayed.
To return to the step 8, press 
a. Press 
a/
b  to select play, and then press 
ENTER 
or  d to start playback.
The screen of the TV
After a period of time, playback of the movie begins.
H The buttons that can be used during playback
Buttons Description
θ/a Stops playback and displays the movie title screen 
(springboard).
FSets pauses and still pictures. Press F or 
d
 to 
return to playback.
κDisplays the TrickPlay screen and fast forwards 
playback.
τDisplays the TrickPlay screen and reverses 
playback.
ENTER Displays the TrickPlay screen and pauses playback.
d Displays the TrickPlay screen, advances one frame 
forward, and pauses playback.
c Displays the TrickPlay screen, advances one frame 
backward, and pauses playback.
RETURN Displays Netfl ix home screen.
EXIT Closes the Netfl ix home screen and switches the 
TV to INPUT mode.
Deactivating Netfl
 ix Function
1 Press MENU to display the menu screen.
2 Press 
c/
d  to select Information, and then press 
ENTER .
3 Press 
a/
b  to select Netfl ix Help, and then press 
ENTER .
4 Press 
c/
d  to select Deactivate, and then press 
ENTER .
To confi rm the Netfl ix status, check the information 
displayed on the screen and click OK.
•
•
•
Using the Internet
-
$  @ @ @ -&  6 / @& @ J O EE


 -$@@@-&6/@&@JOEE