Sharp Lc 40le810 Operation Manual


Initial installation overview
Follow the steps below one by one when using the TV for the first time. \
Some steps may not be necessary depending 
on your TV installation and connection.
Preparation
Connect an antenna cable to the antenna terminal (Page 10).
If necessary, insert a CA card into the CI slot to watch 
scrambled broadcasts (Page 10).
Plug the AC cord into the AC outlet (Page 10).
Product shape varies in some countries.



Run the initial 
settings
Check that the MAIN POWER switch on...

0
Before turning on the power

 
21

Standard DIN45325 plug (IEC 169-2) 75 q coaxial cable
AC cord (product shape varies in some countries)
Check that the MAIN POWER switch on the rear of the TV is turned on 
(;).
Cable clamp (bundle the cables with the clamp)


Place the TV close to the AC outlet, 
and keep the power plug within 
reach.
Inserting the CA card into the CI module
In order to receive coded digital stations, a common interface module (CI module) a\
nd a CA card must be inserted...


Initial auto installation
When the TV is powered on for the first time after 
purchase, the initial auto installation wizard appears. 
Follow the menus and make the necessary settings one 
after another.
Confirm the following before turning on 
the power
Is the antenna cable connected?
Is the AC cord plugged in?
Is the MAIN POWER switch turned on (;)?
E
E
E
Press  “View setting” > 
“Reset” > select “HOME” again.
Setting the country.Press a/b/c/d to select your country or area, 
and then press...


Quick guide
Searching for cable broadcasts
To change each item to the appropriate 
settings:
Press a/b to select the menu, and then 
press ;.
Scrambled stations[Yes]
Search method [Channel]
Start frequency
Network ID[None]
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Reset
Search start
Press a/b/c/d or 0_9 to select or input 
the appropriate item/value, and then press 
;.
Press a/b to select “Search start”, and then 
press ;.
Press c/d to select “Yes” to start searching 
cable...


Quick guide
Checking signal strength and 
channel strength (DVB-T/C)
If you install a DVB-T/C antenna for the first time or 
relocate it, you should adjust the alignment of the 
antenna to receive a good reception while checking the 
antenna setup screen.
Go to “Menu” > “Setup” > “View setting” 
> “Channel settings” > “Antenna setup-
DIGITAL”.
Checking signal strength
Press a/b to select “Signal strength”, and 
then press ;.
Supply voltageCH No.
CurrentMax.
Signal strengthSignal strength...


Daily operation
Switching on/off
Turning on/off the power
Turn on (;) the MAIN POWER switch on the 
rear of the TV (Page 4).
To turn on the TV, press a on the remote control unit.
To turn off the TV, press a on the remote control unit.
Turn off (a) the MAIN POWER switch on the 
rear of the TV (Page 4).
When turning off the power using the MAIN POWER 
switch on the rear of the TV, EPG data will be lost.
Standby mode
To standby modeIf the MAIN POWER switch on the rear of the TV is 
turn on (;),...


Watching TV
Selecting an external video 
source
Once the connection 
is made, press b to 
display the “INPUT” screen, 
and then press b or 
a/b to switch over to the 
appropriate external source 
with ;.
NOTEYou can also select an 
external video source from 
“CH list” > “INPUT”.
•
TV INPUT
Switchable
CH list
Selecting a sound mode
DTV modeIf multi sound modes are received, each time you press 
7 the mode switches as follows.
Audio (ENG)
STEREO
L/R L R LR
CH A CH B CH AB
Audio (ENG) CH A
Audio...


Watching TV
EPG
EPG is a programme list that is displayed on the screen. With the EPG, you can check the schedule of DTV/RADIO/
DATA, view detailed information about them, tune to an event currently on-air.
Useful settings for using EPG
Basic setting
View setting
EPG
If you want to use the EPG for digital stations, select “Yes”. The EPG data must be automatically captured 
while the TV is in standby mode. After setting to “Yes”, 
it may take some time to turn off the power using the 
remote...


Selecting a programme using EPG
Basic operation
The illustrations on this page are explained 
using three digit services.
Display/Close the EPG 
screen
Press EPG.
E
SelectEnterBackExit
AMPM
Programme info. Search by genre Search by date Timer list
NOTEYou can also display the EPG screen from “Menu” > “EPG” > “EPG”.
•
Select a programme
Select the time span
Press c/d to select the time span you want 
to search.
Continue to press d to display programmes in the next 
time span.
E
1
•
Select the...


Watching TV
Display the timer list for TV 
programmes
Press B.Refer to page 18 for the timer setup.
Timer setup using EPG
You can switch to a programme at a set time.
Press EPG.
Press a/b/c/d to select the programme 
you want to set, and then press ;.
Back to EPGWatch No
Programme info.
Next
Press c/d to select “Watch”, and then press 
;.
If you select “No”, the TV returns to the EPG screen.
Press c/d to select “Yes”, and then press 
;.
The selected TV programme is marked with an icon.
Press ;...