Sanyo VPC E60EX User Manual

							145English
DIRECT PRINTING
Your camera supports the PictBridge function. By connecting the camera 
directly to a PictBridge-enabled printer, the camera’s LCD monitor can be 
used to select images and initiate printing (PictBridge printing).
Print preparations
1 Insert the card containing the images you wish to print in the 
camera.
2 Turn the printer on, and use the supplied USB interface cable to 
connect the camera to the printer.
hConnect the camera’s USB/AV terminal to the printer’s USB 
connector.
hThe USB Connection Screen appears on the camera’s LCD monitor.
CAUTION 
Insert and pull out the cable carefully
iDo not use excessive force when connecting and disconnecting cables.
USB/AVPictBridge
PC CAMERA
CANCEL
USB CONNECTION
CARD READER
Supplied dedicated USB 
interface cableTo USB connector on the printer SET button
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							English146
3 Select “PictBridge”, and press the 
SET button.
hThe Print Settings Screen appears.
CAUTION
Caution when connecting a printer
iIf the power to the printer is turned off while it is connected, the camera 
may not operate correctly. If the camera does not operate correctly, 
disconnect the USB interface cable, turn off the camera, and then 
reconnect the cable.
iDuring PictBridge printing, the camera’s button operation response is 
slower.
iIf the camera is powered by the battery pack for printing, make sure that 
the remaining battery charge is sufficient.
PRINTING MODE
ONE IMAGE
Print this image
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							147English
DIRECT PRINTING
To select one image and print it (one image)
Procedure to select one still image and print it.
1 Complete the printing setup (page 145).
2 Select the one image icon Y, and 
press the SET button.
hThe screen to select images for 
printing appears.
3 Toggle the SET button to the left or 
right to display the image you wish 
to print.
hSpecify the image to print.
ONE IMAGE
COPIES:
1
PRINT
EXIT
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							English148
4 Specify the number of prints.
1Select “COPIES”, and press the 
SET button.
2Toggle the SET button up or down 
to specify the number of prints.
3Press the SET button.
h“PRINT” is selected.
5 Press the SET button.
hPrinting begins.
HINT
To cancel printing
1During printing, toggle the SET button down.
hThe Confirm Cancel Printing Screen appears.
2Select “YES”, and press the SET button.
hIf “EXIT” is selected and the SET button is pressed, printing resumes.
ONE IMAGE
COPIES
1
PRINT
EXIT
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							149English
DIRECT PRINTING
To print all the images (all images)
Print all of the images on the card.
1 Complete the printing setup (page 145).
2 Select the all images icon u, and 
press the SET button.
hThe Print All Images Screen 
appears.
3 Select “PRINT”, and press the SET 
button.
hPrinting begins.
CAUTION
Printing is not possible if there are more than 999 still images in the 
card.
iDelete unwanted images before printing.
PRINT
EXIT ALL IMAGES
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							English150
Thumbnail prints (index)
Make an index print of all the images on the card.
1 Complete the printing setup (page 145).
2 Select the index print icon [, and 
press the SET button.
hThe Index Print Screen appears.
3 Select “PRINT”, and press the SET 
button.
hPrinting begins.
INDEX
PRINT
EXIT
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							151English
DIRECT PRINTING
To print the images that are set to print (print reserved images)
Procedure to print all the images that are set to print.
1 Make the print settings (page 102), and complete the printing setup 
(page 145).
2 Select the DPOF icon w, and 
press the SET button.
hThe Print Scheduled Images 
Screen appears.
3 Select “PRINT”, and press the SET 
button.
hPrinting begins.
hPrinting begins about 1 minute after 
the SET button is pressed.
HINT
iIn step 2, if you toggle the SET button to the left or right, you can confirm 
the images that are set to print and their DPOF settings.
CAUTION
iReserved images printing w is not possible if a printer is used that does 
not support your camera’s DPOF function.
DPOF
PRINT
EXIT
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							English152
To change the printer settings and print images 
(change printer settings)
Images are printed according to settings specified by the camera, such as 
paper type, size, layout, printing quality, etc.
1 Complete the printing setup (page 145).
2 Select the printer settings icon v, 
and press the SET button.
hThe Printer Settings Screen 
appears.
MEDIA TYPE:
Specify the type of paper used for 
printing.
PA P E R  S I Z E :
Specify the size of paper used for 
printing.
LAYOUT:
Specify how the images are to be 
arranged on the paper.
QUALITY:
Select the print quality for the 
images.
DATE STAMP:
Print the date the photo was taken.
EXIT:
Return to the PictBridge Screen.PRINTER SETTINGS
MEDIA TYPE
PAPER SIZE
QUALITYLAYOUT
DATE STAMPPRINTER VALUE
PRINTER VALUE
PRINTER VALUE
PRINTER VALUE
PRINTER VALUE
EXIT
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							153English
DIRECT PRINTING
3 Adjust the printer settings.
1Toggle the SET button up or down to select a printer setting 
parameter, and press the SET button.
hThe screen to set the selected parameter appears.
2Toggle the SET button up or down to adjust the setting, and 
press the SET button.
hThe selected parameter is set, and you are returned to the Printer 
Settings Screen.
hFollow the same procedure to adjust the other parameters, as 
desired.
hThe contents of the settings that can be made for each parameter 
will differ depending on the printer.

hThe images will be printed according to the settings specified on the 
printer side.
4 Select “EXIT”, and press the SET button.
hYou are returned to the Printing Mode Screen.
HINT
iThe printer setting parameters will differ depending on the printer that is 
connected.
iTo use printer functions which do not appear on your camera’s Printer 
Settings Screen, select “PRINTER VALUE”.
iIf a function set by the camera is not available in the printer, the camera’s 
printer settings will automatically change to “PRINTER VALUE”.
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							English154
APPENDICES
COMMONLY ASKED QUESTIONS
If you have a question about the camera operation, you might find the answer 
in this compilation of commonly asked questions.
Question Answer Action
PowerWhy doesn’t the 
power turn on?Due to cold 
temperatures, the 
battery pack 
temporarily lost its 
power.Place the camera in 
your pocket to warm 
it up before using it.
Why is the battery 
pack consumed 
so quickly even 
after it was fully 
recharged?The ambient 
temperature is 
ver y low.Keep the battery 
pack in an 
environment of 10 to 
40°C (50 to 104°F).
Why doesn’t 
recharging end?The battery pack 
life has expired.Replace with a new 
battery pack. If this 
is not effective, 
consult your dealer.
Why does the 
 icon 
appear?The remaining 
battery pack 
power is low.Use the supplied AC 
adaptor, or replace 
the battery pack with 
a fully charged one.
ShootingWhy doesn’t the 
touch sensor 
work?You are wearing 
gloves.Remove the glove 
from the hand 
pressing the shutter 
button.
Why does the 
multi-indicator 
flash red?Recorded data is 
being saved on 
the card or to the 
camera’s internal 
memory.Not a malfunction. 
Wait until the multi-
indicator turns off.
Why doesn’t the 
flash operate?The camera has 
determined that 
the image is bright 
enough and the 
flash is not 
necessary.Not a malfunction. 
Capture the image; 
the camera will 
determine when the 
flash is necessary.
Downloaded From camera-usermanual.com Sanyo Manuals