Sanyo Projector Plc Xd2600 User Manual

							
11

Part Names and Functions
✔Note:
To	ensure	safe	operation,	please	observe	the	following	precautions:
–	 Do	not	bend,	drop	or	expose	the	remote	control	to	moisture	or	heat.
–	 For	cleaning,	 use	a	soft	 dry	cloth.	 Do	not	 apply	 benzene,	 thinner,	spray,	
or	any	chemical	material.
Remote Control
⑦
⑭⑩
⑳④
⑱
②
⑧
⑨
⑬
⑯
⑤
⑥
⑪
⑫
⑲
⑮
③
②	AUTO SET buttonExecute	the	setting	of	 Auto	setup	(includes	Input	search,	 Auto	PC	adj.	and	Auto	Keystone	functions)	in	the	setting	menu.(pp.23,	44)
⑤ S-VIDEO button	 Select	the	S-VIDEO	input	source.		(p.36)
⑥	Point ▲▼◄►	buttons	 –	Select	an	item	or	adjust	the	value	in	the	On-Screen	Menu.		(p.21)	 –	Pan	the	image	in	the	Digital	zoom	+/-	mode.		(p.35)
⑬	MUTE button	 Mute	the	sound.		(p.24)
⑦	SCREEN button	 Select	a	screen	mode.		(pp.26,	34-35,	42)
⑮	P-TIMER button	 Operate	the	P-timer	function.		(pp.26,	51)
⑩	NO SHOw button	 Temporarily	turn	off	the	image	on	the	screen.		(p.26)
⑯	LAMP button	 Select	a	lamp	mode.		(pp.25,	53)
⑱	KEySTONE button	 Correct	keystone	distortion.		(pp.23,	45)
⑲	SELECT button	 –		Execute	the	selected	item.		(p.21)	–	Expand 	or 	compress 	the 	image 	in 	Digital 	zoom 	mode. 		(p.35)
⑧		MENU button	 Open	or	close	the	On-Screen	Menu.		(p.21)
⑨	FREEZE button	 Freeze	the	picture	on	the	screen.		(p.25)	
⑫	VOLUME +/- buttons	Adjust	the	volume	level.		(p.24)
①	ON/STAND-By  button 	 Turn	the	projector	on	or	off.		(pp.18-20)
③ COMPUTER 1/2 buttons	 Select	the	COMPUTER	1	or	COMPUTER	2	input	source.						(pp.27,	37)
⑪	D .ZOOM ▲▼	buttons	 Zoom	in	and	out	the	images.		(pp.25,	35)
⑭ IMAGE button	 Select	the	image	mode.		(pp.26,	32,	39)
⑳	COMPONENT button	 Select	the	COMPONENT 	input	source.	(p.37)
④ VIDEO button	 Select	the	VIDEO	input	source.		(p.36)
⑰
⑰	INFO . button	 Operate	the	information	function.		(p.58)
① 
						

							
12

Part Names and Functions
To	ensure	safe	operation,	please	observe	the	following	precautions	:
	●	 Use	two	(2)	AAA	or	LR03	type	alkaline	batteries.
	●	 Always	replace	batteries	in	sets.
	●	 Do	not	use	a	new	battery	with	a	used	battery.
	●	 Avoid	contact	with	water	or	liquid.
	●	 Do	not	expose	the	remote	control	to	moisture	or	heat.
	●	 Do	not	drop	the	remote	control.
	●	 If	the	battery	has	leaked	on	the	remote	control,	carefully	wipe	the	case	clean	and	install	new	batteries.
	●	 Risk	of	an	explosion	if	battery	is	replaced	by	an	incorrect	type.	
	●	 Dispose	of	used	batteries	according	to	the	instructions	or	your	local	disposal	rule	or	guidelines.
Open	the	battery	
compartment	lid.
Install	new	batteries	
into	the	compartment.
Replace	the	
compartment	lid.
Two AAA size batteries
For	correct	polarity	
(+	and	–),	be	sure	
battery	terminals	are	
in	contact	with	pins	in	
compartment.
12
Point 	the 	remote 	control 	toward 	the 	projector 	(Infrared	
Remote 	Receiver) 	when 	pressing 	the 	buttons. 	Maximum	
operating 	range 	for 	the 	remote 	control 	is 	about 	16.4'(5 	m)	
and	60	degrees	in	front	of	the	projector.
Remote Control Operating Range
Remote Control Battery Installation
16.4'
(5	m)
30°Remote	control
30°
The	 2	different	 remote	control	codes	(Code	 1–Code	 2)	are	
assigned	to	this	projector.	Switching	the	remote
control 	codes 	prevents 	interference 	from 	other 	remote	
controls	when	several	projectors	or	video	equipment
next	 to	each	 other	 are	operated	 at	the	 same	 time.	Change	
the	remote	control	code	for	the	projector	first	before
changing	 that	for	the	 remote	 control.	 See	"Remote	 control"	
in	the	Setting	Menu	on	page	53.
Press	and	hold	the	MENU	and	IMAGE	buttons	for	more
than	five	seconds	to	switch	between	the	Code 1	and	Code
2.	The	initial	code	is	set	to	Code 1.
Remote Control Code
MENU button
IMAGE button 
						

							
1

Positioning the Projector
For	projector	 positioning,	 see	the	figures	 below.	The	projector	 should	be	set	 perpendicularly	 to	the	 plane	 of	the	
screen.
Installation
✔Note:
	 •	The 	brightness 	in 	the 	room 	has 	a 	great 	influence 	on 	picture 	quality. 	It 	is 	recommended 	to 	limit 	ambient	
lighting	in	order	to	obtain	the	best	image.
	 •	All	measurements	are	approximate	and	may	vary	from	the	actual	sizes.
Adjustable Foot
Adjustable	Foot
Foot	Lock	Latch
Projection	angle	can	be	adjusted	up	to	10.0	degrees	with	
the	adjustable	foot.	
Lift	the	front	of	the	projector	and	push	the	foot	lock
latch	on	the	projector.
Release	the	foot	lock	latch	to	lock	the	adjustable	foot
and	rotate	the	adjustable	foot	to	adjust	the	position	and
tilt.
To	retract	the	adjustable	foot,	lift	the	front	of	the
projector	and	push	and	undo	the	foot	lock	latch.
Keystone	distortion	of	the	projected	image	can	be
corrected	by	menu	operation.(see	pages	23,	44-45)
A
B
100
150
200250
167
125
83
300(wide)
40
300(tele)
38.7(11.80m)
32.3(9.84m)
21.5(6.55m)
16.1(4.90m)
Max. ZoomMin. Zoom
A : B  =  6 : 1(Inch Diagonal)
10.7(3.26m)
(Center)
4.3(1.30m)
Screen Size(W x H) mm   4 : 3 aspect ratio
40”
Zoom (max)
813 x 610
4.3(1.30m)
100”
2032 x 1524
10.7(3.26m)
150”
3048 x 2286
16.1(4.90m)
200”
4064 x 3048
21.5(6.55m)
300”
6096 x 4572
32.3(9.84m)
Zoom (min)5.1(1.55m)12.9(3.92m)19.4(5.90m)25.8(7.87m) 38.7(11.80m) 
						

							
14

Installation
Connecting to a Computer
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	AC	outlet	before	connecting	
cables.
Cables used for connection 
•	VGA	Cables	(Mini	D-sub	15	pin)	*(Only	one	cable	is	supplied.)
•	Audio	Cables
(*One	cable	is	supplied;	other	cables	are	not	supplied	with	the	projector.)
✔Note:
	 •	Input	sound	to	the	 AUDIO	IN	terminal	when	using	the	COMPUTER	IN	1/	S-VIDEO	IN	/	COMPONENT 	IN
				and	the	COMPUTER	IN	2/MONITOR	OUT	terminals	as	input.
	 •	When	the	AUDIO	OUT	is	plugged-in,	the	projector's	built-in	speaker	is	not	available.
		•	When	the	cable	is	of	the	longer	variety,	it	is	advisable	to	use	the	COMPUTER	IN	1	/S-VIDEO	IN	/COMPONENT 	IN	and	
not	the	COMPUTER	IN	2/MONITOR	OUT.
External	Audio	Equipment
Audio	cable	
(stereo)
Audio	cable		
(stereo)
Audio	Output
AUDIO	IN
AUDIO	OUT 	(stereo)
Audio	Input
Monitor	Input													or	Monitor	Output
COMPUTER	IN	2	/	MONITOR	OUT
VGA	cable	
COMPUTER		IN	1/	S-VIDEO	IN/COMPONENT 	IN
VGA	cable	
Monitor	Output
This	terminal	is	switchable.	Set	up	the	terminal	as	either	Computer	input	or	Monitor	output.	(See	Page	49.) 
						

							
15

Installation
Connecting to Video Equipment
Cables used for connection  
•	Video	Cable	
•	S-Video	Cable	
•	S-Video-VGA	Cable	
•	Audio	Cables
(Cables	are	not	supplied	with	the	projector.	)
✔Note:
	 •	When	the	 AUDIO	OUT	is	plugged-in,	the	projector's	built-in	speaker	is	not	available.
	 •	See	page	73	for	ordering	optional	cables.
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	 AC	outlet	before	connecting	
cables.
External	Audio	Equipment
Audio	cable			(stereo)
S-Video	cable		
Composite	Video	and	 Audio	Output
S-Video	Output	and	Audio	output
Audio	Input
AUDIO	IN
S-Video-VGA	
cable		
Video	cable			
COMPUTER		IN	1/	S-VIDEO	IN/COMPONENT 	IN
VIDEO	IN
Audio	cable			(stereo)
AUDIO	OUT	(stereo)
AUDIO	IN
Audio	cable			(stereo) 
						

							
16

Installation
Connecting to Component Video and RGB (Scart) Equipment
✔Note:
	 •	When	the	AUDIO	OUT	is	plugged-in,	the	projector's	built-in	speaker	is	not	available.
	 •	See	page	73	for	ordering	optional	cables.
Cables used for connection	
•	Audio	Cables	
•	Scart-VGA 	Cable	
•	Component	Cable	
•	Component-VGA 	Cable	
(Cables	are	not	supplied	with	this	projector.)		
External	Audio	Equipment
AUDIO	IN
Audio	cable	(stereo)
Audio	cable	(stereo)
Audio	Input
Component	Video	Output(Y,	Pb/Cb,	Pr/Cr)Audio	OutputRGB	Scart	21-pin	Output
Scart-VGA 	cable	
Component-VGA	cable
AUDIO 	OUT 	(stereo)
Component	cable
COMPUTER	IN	1/	S-VIDEO	IN	/	COMPONENT 	IN	
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	 AC	outlet	before	connecting	
cables. 
						

							
17

Installation
Connecting the AC Power Cord
This	projector	 uses	nominal	 input	voltages	 of	100-240	 V	AC	
and 	it 	automatically 	selects 	the 	correct 	input 	voltage. 	It 	is	
designed	 to	work	 with	single-phase	 power	systems	 having	a	
grounded	 neutral	conductor.	 To	reduce	 the	risk	 of	electrical	
shock,	do	not	plug	into	any	other	type	of	power	system.
If	you 	are 	not 	sure 	of 	the 	type 	of 	power 	being 	supplied,	
consult	your	authorized	dealer	or	service	center.
Connect 	the 	projector 	with 	all 	peripheral 	equipment 	before	
turning	the	projector	on.
✔Note:
					Unplug	the	 AC	power	cord	when	the	projector	is	not	
					in	use.		When	this	projector	is	connected	to	an	outlet
					with	the	AC	power	cord,	it	is	in	Stand-by	mode	and
					consumes	a	little	electric	power.
To	the	AC	outlet.
(200 - 240 V AC)
NOTE ON THE POwER CORD
AC	power	cord	must	meet	requirement	of	the	country	where	you	use	the	projector.
Confirm	the	 AC	plug	type	with	the	chart	below	and	proper	 AC	power	cord	must	be	used.
If	supplied	AC	power	cord	does	not	match	your	 AC	outlet,	contact	your	sales	dealer.
To	power	cord	
connector	on	your	
projector.
Projector sideAC outlet side
To	the	AC	outlet.
(120 V AC)
For the U .S .A . and Canada
To	the	AC	outlet.
(200 - 240 V AC)
For the U .K .For Continental Europe
	 CAUTION
The	AC	outlet	 must	be	near	 this	equipment	 and	must	 be	
easily	accessible.
Connect 	the 	AC 	power 	cord 	(supplied) 	to 	the	
projector.
Ground
Ground➞
➞ 
						

							
18

The	preparation	display	will	disappear	
after	30	seconds.
(See	page	53	for	Lamp	control	status.)
Turning On the Projector
Connect	the	projector’s	AC	power	cord	into	an	AC	
outlet.	The	POWER	indicator	lights	red.	Open	the	lens	
cap	(see	pages	8,	61).
Press	the	ON/STAND-BY 	button	on	the	top	control	or	
on	the	remote	control.	The	POWER	indicator	lights	
green	and	the	cooling	fans	start	to	operate.	 The	
preparation	display	appears	on	the	screen	and	the	
countdown	starts.	
2

1Complete	peripheral	connections	(with	a	computer,	
VCR,	etc.)	before	turning	on	the	projector.		
Selected Input Source and Lamp Control
✔Note:
			The	Filter	warning	and	Lamp	replacement	
icons	may	appear	on	the	screen						
depending	on	the	usage	state	of	the	
projector.
Basic Operation
16
Lamp	control	status
Video
4After	the	countdown,	the	input	source	that	was	selected	
the	last	time	and	the	lamp	control	status	icon	(see	page	
53)	appear	on	the	screen.
✔Note:
	 •	When	 the	Logo	 select	 function	 is	set	 to	Off,	the	 logo	 will	
not	be	shown	on	the	screen	(p.46).
	 •	When	Countdown  off	or	Off	is	 selected	 in	the	 Display	
function, 	the 	preparation 	display	will 	not 	be 	shown 	on	
the	screen	(p.45).
	 •	When	 the	Input	 Search	 function	 is	set	 to	On2,	the	 input	
signal	will	be	searched	automatically	(p.44).
	 •	When	Off	is	 selected	 in	the	 Display	 function,	 the	Video/
PC	selection 	window 	and 	the 	input 	signal 	guidance	
window	are	not	shown	on	the	screen.	(p.45)
5If	there	is	no	signal	input	when	start	on	the	projector,
or	the	current	signal	is	missed	while	operating	the
projector,	the	Video/PC	selection	window	will	be
displayed	on	the	screen,	please	move	the	pointer	to
input	source	desired	by	pressing	the	Point	▲▼	buttons
and	press	the	SELECT 	button.	And	then	follow	the
input	signal	guidance	window	to	correct	the	signal	and
connection.
If	the	projector	is	locked	with	a	PIN	code,	PIN	code	input	
dialog	box	will	appear.	Enter	the	PIN	code	as	instructed	
on	the	next	page.
Video / PC selection window
Input signal guidance window
Video / PC selection window
Input signal guidance window
    Project Video
Project Computer
Cancel
Project Video
   Project Video
Project Computer
Cancel
Project Computer
No	signal
Current	Input	setting:Video	
Is	signal	 processed	 correctly?		I s	c a b l e 	c o n n e c t e d 	p r o p e r l y ?		
No	signal
Current	Input	setting:RGB
Is	 signal	 processed	 correctly?		I s	c a b l e 	c o n n e c t e d 	p r o p e r l y ?		 
						

							
19

what is PIN code?
PIN	(Personal	Identification	Number)	code	is	a	security	
code	that	allows	the	person	who	knows	it	to	operate	the	
projector.	Setting	a	PIN	code	prevents	unauthorized	use	of	
the	projector.
A	PIN	code	consists	of	a	four-digit	number.	Refer	to	the	PIN	
code	lock	function	in	the	Setting	Menu	on	pages	54-55	for	
locking	operation	of	the	projector	with	your	PIN	code.
Enter a PIN code
Use	the	Point	▲▼	buttons	to	enter	a	number.	Press	the	
Point	◄	►	buttons	to	fix	the	number	and	move	the	red	
frame	pointer	to	the	next	box.	 The	number	changes	to	“✳”.	
If	you	fixed	an	incorrect	number,	use	the	Point	◄	►	buttons	
to	move	the	pointer	to	the	number	you	want	to	correct,	and	
then	enter	the	correct	number.
Repeat	this	step	to	complete	entering	a	four-digit	number.
After	entering	the	four-digit	number,	move	the	pointer	to	Set.	
Press	the	SELECT	button	so	that	you	can	start	to	operate	
the	projector.
If	you	entered	an	incorrect	PIN	code,	PIN code	and	the	
number	(✳✳✳✳)	will	turn	red	for	a	moment.	Enter	the	
correct	PIN	code	all	over	again.
CAUTION ON HANDLING PIN CODE
If	you	forget	your	PIN	code,	the	projector	can	no	
longer	be	started.	Take	a	special	care	in	setting	
a	new	PIN	code,	write	down	the	number	in	a	
column	on	page	76	of	this	manual	and	keep	it	
on	hand.	Should	the	PIN	code	be	missing	or	
forgotten,	consult	your	dealer	or	service	center.
After	the	OK	icon	disappears,	
you	can	operate	the	projector.		
PIN Code Input Dialog Box
✔Note:
	 •	If	the	PIN	code	number	is	not	entered	or	wrong	PIN	
code	number	is	entered	within	three	minutes	after	the	
PIN	code	dialog	box	appeared,	the	projector	will	be	
turned	off	automatically.
	 •	The	“1234”	is	set	as	the	initial	PIN	code	at	the	factory.
Basic Operation 
						

							
20

TO	MAINTAIN	THE	LIFE	OF	THE	LAMP,	ONCE	
YOU	TURN	 THE	PROJECTOR	ON,	WAIT 	AT 	
LEAST 	FIVE	MINUTES	BEFORE	 TURNING	IT	
OFF.
Power off?	disappears	after	4	seconds.
Turning Off the Projector
Press	the	ON/STAND-BY 	button	 on	the	 top	control	 or	
on	the	 remote	 control,	 and	Power off? appears	 on	the	
screen.
Press 	the 	ON/STAND-BY 	button 	again 	to 	turn 	off 	the	
projector.	 The	POWER	 indicator	 starts	to	blink	 red,	and	
the	cooling	 fans	keep	 running.	 (You	can	select	 the	level	
of	fans’ 	quietness	 and	speed.	 See	“Fan”	 on	page	 56.)	
At	this	 time,	 you	can	unplug	 the	AC	 power	 cord	even	 if	
the	fans	are	still	running.
1
2
When 	the 	projector 	has 	cooled 	down 	enough, 	the	
POWER 	indicator 	stops 	blinking 	and 	you 	can 	turn 	on	
the	projector.	
✔Note:
	 •	When	 the	Direct	 on	function	 is	set	 to	On,	the	 projector	
will	be 	turned 	on 	automatically 	by 	connecting 	the 	AC	
power	cord	to	an	 AC	outlet	(p.50).
	 •	The	running	 speed	of	cooling	 fans	is	changed	 according	
to	the	temperature	inside	the	projector.
	 •	Do	not	put	the	projector	 in	a	case	 before	 the	projector	 is	
cooled	enough.
	 •	If	the	WARNING	indicator	blinks	or	lights	red,	see	
“WARNING	indicator”	on	page	59.
	 •	While	the	POWER	 indicator	 is	blinking,	 the	lamp	 is	being	
cooled	 down	and	the	projector	 cannot	be	turned	 on.	Wait	
until	 the	POWER	 indicator	 stops	blinking	 to	turn	 on	the	
projector	again.
		•	The 	fan 	rotation 	will 	terminate 	directly 	if 	the 	AC 	power	
cord 	is 	unplugged 	immediately 	after 	the 	projector 	is	
turned	off.
		•	The 	projector 	can 	be 	turned 	on 	after 	the 	POWER	
indicator 	turns 	red. 	The 	waiting 	time 	to 	restart 	will 	be	
shortened	when	the	normal	power-off	processing	for	fan	
	 	 cooling 	is 	completed, 	compared 	with 	the 	time 	the 	AC	
power 	cord 	is 	immediately 	unplugged 	after 	the 	power-
off.	
Basic Operation
DO	NOT 	OPERATE	 THE	PROJECTOR	
CONTINUOUSLY 	WITHOUT	REST.	
CONTINUOUS	USE	MAY 	RESULT	IN	
SHORTENING	 THE	LAMP	LIFE.	TURN	OFF	 THE	
PROJECTOR	 AND	LET	STAND	FOR	 ABOUT	AN	
HOUR	IN	EVERY 	24	HOURS.
✔Note:
	 •	When	using	the	Direct	 OFF	function,	 you	
cannot	restart 	the 	projector 	immediately	
after 	the 	power 	is 	disconnected. 	If 	the	
external 	power 	supply 	is 	suddenly 	cut	
off, 	the 	fan 	stops 	immediately. 	The 	lamp	
remains 	high 	temperature 	and 	needs 	to	
be	cooled.
You	can	disconnect	the	power	cord	from	the	
wall	outlet	or	turn	off	the	breaker	even	during	
projection	without	pressing	the	on/stand-by	
button.
Direct OFF Function