Sanyo Plc Xp41l Projector User Manual

							41
APPENDIX
Remote Control Unit
does not work.Check batteries.
Check ALL-OFF switch on Remote Control Unit is set to “ON”.
Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
Check transmitted signal mode from Remote Control Unit.
(See“SETTING” section on page 36.)
Problem:Try these Solutions
Wireless Mouse
function does not
work.Check cable connection between a projector and your computer.
Check mouse setting on your computer.
Turn a projector on before turning on a computer.
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If a projector fails to work properly, see TROUBLESHOOT-
ING section on page 40, 41. To correct failure, try Solutions.
If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or
store where you purchased unit.
Give model number and explain difficulty. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC). 
						

							42
APPENDIX
Multi-media Projector
Accessories
Specifications are subject to change without notice.
TECHNICAL SPECIFICATIONS
1.3 TFT Active Matrix type, 3 panels
17.4 lbs (7.9 kg)
12.6 x 6.6 x 16.8 (319 mm x 168 mm x 429.5 mm) 
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
Up and Down
800 TV lines (HDTV)
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Owner’s Manual
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
VGA Cable
MAC/VGA Adapter
3 Types Control Cable (For PS/2, Serial and ADB port) 
Protective Dust Cover
Lens Cover
Projector Type
Net Weight
Dimensions (W x H x D)
Panel Resolution
Number of Pixels
Color System
Scanning Frequency
Horizontal Resolution
Built-in Speakers
Operating Temperature
Storage Temperature
LCD Panel System
275 watt typeProjection Lamp
0˚ to 10.5˚Feet Adjustment
Power Source : AA, UM3 or R06 Type x 2
Operating Range : 16.4’ (5m) / ±30˚
Dimensions : 2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
Net Weight : 0.36 lbs (165 g) (including batteries)
Laser Pointer : Class IILaser  
(Max. Output : 1mW / Wave length : 650±20nm)
Remote Control Transmitter
480i, 480p, 575i, 575p, 720p, 1035i and 1080iHigh Definition TV Signal
AC 100 ~ 120 V (4.8 A  Max. Ampere), 50 / 60 Hz  (The U.S.A and Canada)
AC 200 ~ 240 V (2.4 A  Max. Ampere), 50 / 60 Hz  (Continental Europe and The U.K.)
Voltage and 
Power Consumption
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Motorized Lens Shift
DVI Terminal (Digital), HDB 15-pin Terminal (Analog)
and Stereo Mini Type Jack (Audio)Input 1 Jacks
BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V), Stereo Mini
Type Jack (Audio)Input 2 Jacks
RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)
and DIN 4-pin (S-Video)Input 3 Jacks
DIN 8-pin (Control port), USB port (Series B receptacle), Wired Remote Jack
and PJ-Net Organizer Connector Other Jacks
Adjustable from 31 to 400Projection Image Size (Diagonal)
F1.8 ~ 2.1 lens with f=48.4 mm ~ 62.8 mm Motor zoom and focusProjection Lens
4.6 (1.4 m) ~ 47.3 (14.4 m)Throw distance 
						

							43
APPENDIX
CONFIGURATIONS OF TERMINALS
COMPUTER INPUT-1 TERMINAL (ANALOG)
Terminal : HDB15-PIN 
Connect display output terminal of computer to this terminal with VGA Cable (supplied). When connecting Macintosh
computer, MAC Adapter (supplied) is required.
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V Power
Horiz. sync.
Ground (Vert.sync.)
DDC Data
Sense 0
Vert. sync.
DDC Clock
9
13
10
12
11
14
15
Pin Configuration
Terminal : Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this connector with Control Cable (supplied).
12
345876
Pin Configuration
CONTROL PORT CONNECTOR
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS / CTS
T X D
GND
GND
-----
ADB
-----
GND
-----
-----
-----
GND
PS/2SerialADB
1
2
3
4
5
6
7
8
COMPUTER INPUT-1 TERMINAL (DIGITAL)
Terminal : DVI 24-pin 
Connect display output terminal of computer to this terminal with DVI cable (for Single Link T.M.D.S. / not supplied).  
1917
21018
31119
41220
51321
61422
71523
81624
T.M.D.S. Data2–
No Connect
T.M.D.S. Data2+
No Connect
T.M.D.S. Data2 Shield
DDC Clock
DDC Data
No Connect
1
5
2
4
3
6
7
8
Pin ConfigurationT.M.D.S. Data1–
No Connect
T.M.D.S. Data1+
No Connect
T.M.D.S. Data1 Shield
+5V Power
Ground (for +5V)
Hot Plug Detect
9
13
10
12
11
14
15
16
T.M.D.S. Data0–
No Connect
T.M.D.S. Data0+
No Connect
T.M.D.S. Data0 Shield
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
17
21
18
20
19
22
23
24
Vcc
- Data
+ Data
Ground
1
2
3
4
USB CONNECTOR (Series B)
Pin Configuration
Connect USB port terminal on your computer or peripheral equipment to this connector with USB Cable (not supplied).
2
341 
						

							Printed in Japan
Part No. 610 297 8445 (1AA6P1P3150-- MB8AA)
SANYO Electric Co., Ltd