Sanyo Plc Xf1000 Projector User Manual

							61
Maintenance and Care
Check the number of lamp to be replaced on the Lamp 
Status Display.
Loosen a screw on the Lamp Cover. Slide and open the 
Lamp Cover. (See the right figure.)1
3
Loosen two screws and pull out the Lamp to be replaced 
by grasping handle.4
Turn off the projector, press the Main On/Off Switch to Off 
and unplug the AC power cord from the AC outlet.  Let 
the projector cool for at least 45 minutes.2
Replace the Lamp with a new one and tighten two 
screws.  Make sure the Lamp is set properly.
6
Follow these steps to replace the lamp.Put the Lamp Cover back and tighten a screw. 
5
7
8
Connect  the AC Power Cord to the projector and turn on 
the projector.
Reset the Lamp Replacement Counter. (Refer to section 
"Resetting the Lamp Counter" on page 62.)
NOTE :    Do not reset LAMP REPLACEMENT COUNTER when 
lamp is not replaced.
SCREW
LAMP 
COVER
SCREWS
Make sure which number of lamp needs to be 
replaced on Lamp Status Display.
Figure shows case of replacing LAMP 1. LAMP 2
LAMP 1
CAUTION :   DO NOT OPERATE THE PROjECTOR  wHILE ANy OF LAMPS IS REMOVED  . IT MA y RESULT IN 
MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS  .
NOTES ON LAMP REPLACEMENT
To  maintain  quality  of  picture  (better  balance  of  color  and  brightness  in  entire  screen),  we 
recommend replacing both 2 lamps at a time . 
Lamp Replacement
For continued safety, replace with a lamp assembly 
of the same type.
Do not drop the lamp assembly or touch a glass 
bulb! The glass can shatter and may cause injury.
Allow the projector to cool, for at least 45 minutes 
before you open Lamp Cover.  The inside of the 
projector can become very hot.
CAUTION
TURN OFF THE UV LAMP BEFORE 
OPENING THE LAMP COVER.
w
ARNING:
When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the 
screen and LAMP 1/2 REPLACE indicator lights orange. Replace the lamp with a new one promptly. The timing 
when the LAMP 1/2 REPLACE indicators should light is depending on the lamp mode.Indicators
LAMP 1 / 2 REPLACE indicators Lamp replacement icon
✔Note: 
• The Lamp replacement icon will not appear 
when the Display function is set to “Off” (p.48), 
or during “Freeze” (p.29). 
						

							62
Maintenance and Care
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer.  When ordering a Projection Lamp, give the 
following information to the dealer.
 l  Model No  . of your projector    :  PLC-XF1000
 l  Replacement Lamp Type No  . :  POA-LMP128
               (Service Parts No. 610 341 9497)
Resetting the Lamp Counter
Be  sure  to  reset  the  Lamp  counter  after  the  lamp  is  replaced. When  the  Lamp  counter  is  reset,  the  LAMP  1/2 
REPLACE indicator stops lighting and the Lamp replacement icon disappears.
✔Note:
 • Do not reset the Lamp counter without replacing the lamp. 
Be sure to reset the Lamp counter only after replacing the 
lamp.Press the MENU button to display the On-Screen Menu. 
Use the Point 7 8 buttons to move the red frame pointer 
to the Setting Menu icon 
Use the Point ed buttons to move the red frame pointer 
to Lamp counter and then press the SELECT button. 
A dialog box appears. Select a lamp and the “Lamp 
replacement counter Reset?” appears. Select [Yes] to 
continue.
1
2Lamp counter
Select a lamp and the “Lamp 
replacement counter Reset?” 
appears.
Select [Yes] again 
to reset the lamp 
counter.
Select [Yes],  then another 
confirmation box appears.
Another confirmation dialog box appears and select [Yes] 
to reset the Lamp counter.3 
						

							63
This projector uses a high-pressure lamp which must be handled carefully and properly. 
Improper handling may result in accidents, injury, or create a fire hazard.
l Lamp  lifetime  may  differ  from  lamp  to  lamp  and  according  to  the  environment  of  use. There  is  no 
guarantee  of  the  same  lifetime  for  each  lamp.  Some  lamps  may  fail  or  terminate  their  lifetime  in  a 
shorter period of time than other similar lamps.
l If  the  projector  indicates  that  the  lamp  should  be  replaced,  i.e.,  if  the  LAMP  1/2  REPLACE  indicators 
light up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow 
carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp 
with the LAMP 1/2 REPLACE indicators lighted may increase the risk of lamp explosion. 
l Lamp  may  explode  as  a  result  of  vibration,  shock  or  degradation  as  a  result  of  hours  of  use  as  its 
lifetime  draws  to  an  end.  Risk  of  explosion  may  differ  according  to  the  environment  or  conditions  in 
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLO wING SAFETy PRECAUTIONS SHOULD BE TAKEN .
If  a  lamp  explodes,  disconnect  the  projector’s  AC  plug  from  the  AC  outlet  immediately.  Contact  an 
authorized  service  center  for  a  checkup  of  the  unit  and  replacement  of  the  lamp.  Additionally,  check 
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out 
from  the  cooling  air  circulation  holes.  Any  broken  shards  found  should  be  cleaned  up  carefully.  No  one 
should  check  the  inside  of  the  projector  except  those  who  are  authorized  trained  technicians  and  who 
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those 
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken 
glass.
          LAMP HANDLING PRECAUTIONS
Maintenance and Care 
						

							64
Turn off the projector, press the Main On/Off Switch to Off 
and unplug the AC power cord from the AC outlet before 
cleaning.
Gently wipe the projection lens with a cleaning cloth that 
contains a small amount of non-abrasive camera lens 
cleaner, or use a lens cleaning paper or commercially 
available air blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch 
the surface of the lens.
Cleaning the Projector Cabinet
Turn off the projector, press the Main On/Off Switch to Off 
and unplug the AC power cord from the AC outlet before 
cleaning.
Gently wipe the projector body with a soft dry cleaning 
cloth. When the cabinet is heavily soiled, use a small amount 
of mild detergent and finish with a soft dry cleaning cloth. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch 
the surface of the cabinet.
When the projector is not in use, put the projector in an 
appropriate carrying case or cover to protect it from dust and 
scratches.
Cleaning the Projection Lens
Maintenance and Care
CAUTION
Do not use any flammable solvents or air sprays 
on the projector and in its vicinity. The explosion or 
fire hazard may occur even after the AC power cord 
is unplugged because the temperature inside the 
projector is extremely high due to the lamps. 
In addition, there is a risk that the internal parts 
may be damaged not only by the flammable air 
spray but also by the cold air. 
						

							65
The WARNING indicators show the state of the function which protects the projector. Check the state of the 
WARNING TEMP. indicator and the LAMP indicator to take proper maintenance. 
Warning Indicators
The projector is shut down and the WARNING TEMP. 
indicator is blinking red.
When the temperature inside the projector reaches a 
certain level, the projector will be automatically shut down 
to protect the inside of the projector. The LAMP indicator 
turns red brighter and the WARNING TEMP indicator 
blinks while the projector is being cooled down. When the 
projector has cooled down enough (to its normal operating 
temperature), it can be turned on again by pressing the ON/
STAND-BY button.
✔Note:
• The WARNING TEMP. indicator continues to blink even after the 
temperature inside the projector returns to normal. When the projector 
is turned on again, the WARNING TEMP. indicator stops blinking. 
Then check the matters below:
–   Did you provide appropriate space for the projector to be 
ventilated? Check the installing condition to see if the air 
vents of the projector are not blocked.
–   Has the projector been installed near an Air-Conditioning/ 
Heating Duct or Vent? Move the installation of the 
projector away from the duct or vent.
–   Is the filter clean? Replace the filter with a new one.
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE 
AC POWER CORD CONNECTED UNDER AN 
ABNORMAL CONDITION. IT MAY RESULT IN FIRE 
OR ELECTRIC SHOCK.
Indicators
Indicators
w ARNING TEMP  .
blinking red
Maintenance and Care
The projector is shut down; and the LAMP indicator is 
lighting and other indicators are blinking.
When the projector detects an abnormal condition, it 
will be automatically shut down to protect the inside of 
the projector and the LAMP indicator lights on and other 
indicators blink. In this case, unplug the AC power cord and 
plug it, and then turn on the projector once again to verify 
operation. If the projector cannot be turned on and these 
indicators are still lighting and blinking, unplug the AC power 
cord and contact the service center.
LAMP indicator lights on 
and other indicators blink . 
						

							66
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described \
on pages 20–21.
2.  Check the cable connection. Make sure that all computers, video equipment, and power cords are properly 
connected.
3.  Make sure that all power is switched on.
4.  If the projector still does not produce an image, restart your computer.
5.  If an image still does not appear, disconnect the projector from your computer and check your computer 
monitor’s display. A problem may be noticed with your graphics controller rather than with the projector. 
(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the 
projector. Turn on equipment in the order of the projector and computer.)
6.  If a problem still persists, check the following solutions.
Appendix
Problem: Solutions
No power.
–Plug the power cord of the projector into the AC outlet.
–Turn the MAIN ON/OFF switch to ON.
–Press the ON/STAND-BY Button to ON.
–Make sure the READY Indicator lights.
– Check  the  indicators.  If  the  LAMP  indicator  lights  and  the  other  indicators  blink,  the 
projector cannot be turned on. (Refer to page 65.)
–Check the projection lamp. (Refer to page 61.)
PIN code dialog box 
appears at start-up.–  PIN code lock is being set. Enter a PIN code; the “1234” or numbers  you have set. (See 
pages 23, 53-54.)
The initial display is not 
shown.–Make sure “Off ” or “Countdown Off” are not chosen at Display function.
  (See “SETTING” section on page 48.)
The initial display is not 
same with the default 
one.–Make sure “User” or “Off” are not chosen at Logo select function.
  (See “SETTING” section on page 49.)
When the projector is on 
and you press the input 
button, an icon other 
than the Lamp mode icon 
appears.
–That is the Filter warning icon. Refer to page 56.
An icon other than Input 
mode or Lamp mode icon 
appears.
–  That is the Lamp replacement icon or the Filter warning icon. See pages 55-56.
No image.
–Check the connection between your computer or video equipment and the projector.
– See  if  the  input  signal  is  correctly  output  from  your  computer.  Some  laptop  computers 
may  need  to  be  changed  the  setting  for  monitor  output  when  connected  to  the 
projector. See your computer’s instruction manual for the setting.
–It takes about 20 seconds to display an image after turning on the projector.
–See if the selected system is corresponding with your computer or video equipment.
–  Select correct input source once again through menu operation. (See pages 31, 41-42.)
–  Make sure the temperature is not out of Operating Temperature (41˚F–104˚F [5˚C–40˚C]). 
						

							67
	
appears on the screen
–The end of lamp life is approaching. Replace the lamp with a new one promptly.  
  (See page 55.)
appears on the screen
–  The  filter  is  out  of  scroll.  Replace  the  filter  cartridge  with  a  new  one  promptly.  (See 
pages 57-58.)
The image is out of focus.
–Adjust the focus of the projector.
–Check Projection Lens to see if it needs cleaning.
 ✔Note:   Moving  the  projector  from  a  cool  temperature  location  to  a  warm  temperature 
location  may  result  in  moisture  condensation  on  Projection  Lens.    In  such  cases, 
leave the projector OFF and wait until condensation evaporates.
–  Projecting  from  excessive  slant  angle  to  the  screen  may  cause  keystone  distortion  and 
partial imperfect focus.
The image is not bright 
enough.
–Check if “Contrast” or “Brightness” are adjusted properly. (See page 45.) 
–Check if “Image level” is selected properly. (See pages 38, 42.)
–Check the Lamp control function. ( See “SETTING” section on page 51.)
– Check  the  Lamp  1/2  replace  indicators.  If  it  lights,  the  end  of  lamp  life  is  approaching. 
Replace the lamp with a new one promptly. (See page 61.)
–  The  image  is  darker  when  1  lamp  mode  is  selected,  compared  with  2  lamp  mode. 
Check the lamp mode at SETTING section on page 51. 
The color is strange.–Check the Input signal, color system, video system, or computer system mode.
The image is Left/Right 
reversed.–Check the Ceiling / Rear function. (See pages 40, 44.)
The image is Top/Bottom 
reversed.–Check the Ceiling function. (See pages 40, 44.)
The image is distorted or 
runs off.–Check “PC Adjust” menu or “ Screen” menu and adjust them.
Auto PC adjustment 
function does not work.– Check  the  Input  signal.  Auto  PC  Adjustment  function  cannot  work  when  480p,  575p, 
720p,  480i,  575i,  1035i,  or  1080i  is  selected  or  when  the  digital  signal  is  input  into  DVI 
terminal. (See page 35.) 
Some displays are not 
seen during the operation.–Check the Display function. (See page 48.)
The setting does not 
remain after turning off 
power.– Make  sure  you  selected  “Store”  after  adjusting  settings.  Some  settings  cannot  be 
stored if not registered with “Store”.
Power management 
function does not work.– Power  management  function  cannot  work  while  “Freeze”  function  is  running  or  the 
shutter is closed.
Image disappears 
automatically.– Check the power management function in the Setting. The power management is set to 
"On" at the factory.
Capture function does not 
work.–Check the connection to see if there is signal.
Some menus cannot be 
selected.–Each of the Video Input and Computer Input has a limit on selectable menus.
Appendix 
						

							68
wARNING: 
High voltages are used to operate this projector  . Do not attempt to open the cabinet .
If problems still persist after following all operating instructions, contact the dealer where you purchased the projector 
or  the  service  center.  Specify  the  model  number  and  explain  about  the  problem. We  will  advise  you  how  to  obtain 
service.
This  symbol  on  the  nameplate  means  the  product  is  Listed  by  Under writers 
Laboratories  Inc.  It  is  designed  and  manufactured  to  meet  rigid  U.L.  safety 
standards against risk of fire, casualty, and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
Pixelworks ICs used.
Appendix
The power is turned off 
automatically.–  Power  management  function  runs  by  initial  setting.  Check “SETTING”  section  on  page 
52.
You cannot operate with 
the side control.–  The  side  control  is  not  available  If  the  side  control  is  locked  at  “Key  lock”  under 
“Security” of SETTING section. Please check “SETTING” section on page 53.
The Remote Control does 
not work.
–Check the batteries.
–Check if the RC sensor is set properly. (See page 52.)
–Make sure no obstruction is between the projector and remote control.
–Make sure you are not too far from the projector when using the remote control.
  Maximum operating range is 16.4’ (5m).
– Make  sure  that  the  remote  control  code  conforms  to  the  projector ’s  code.  (See 
“SETTING” section on page 52.)
–  Make sure the reset switch in the compartment lid on back of the remote control is set 
to use position.
–Unlock the Key lock function for the remote control. (See page 53.)
–  Wireless remote control does not work when the remote control cable is connected to 
the projector. (See page 15.)
Indicators blinks or lights.– Check  the  status  of  the  projector  with  referring  to  “  INDICATORS  AND  PROJECTOR 
CONDITION” on pages 72-74.
appears on the screen
–Your operation is invalid. Operate correctly.
Unable to unlock the Logo 
PIN code lock, Security 
key lock or Security PIN 
code lock.
–Contact the dealer where you purchased the projector or the service center.
Forget the Logo PIN code 
or Security PIN code. –Contact the dealer where you purchased the projector or the service center. 
						

							69
Menu Tree
InputRGB (PC analog)Go to System (1)Input 1
Y, Pb/Cb,Pr/Cr
Computer Input/Video Input
RGB (Scart)
RGB (PC digital)
RGB (AV HDCP)
Input 3
RGB Go to System (1)
Go to System (3)
Go to System (2)Video
S-video
Input 2
Go to System (1)
Input
H-sync freq.
V-sync freq.
Projector
Information
Key lock
ScreenLanguageLamp mode
Power management
Security
Remote control
Quit0–63
0–63
Off/On/Film
Image AdjustContrastBrightnessColor ✽Tint ✽
RedGreenBlue
Sharpness
ResetStore
Gamma
Progressive ✽
0–63
0–63
0–63
0–31 
0–15
Image 1
Yes / No
Quit
Off/OnNoise reduction ✽
0–63
0–63
✔Note:
•The Menu display varies depending on the input signal.
Information Image Adjust
✽Displayed in grayout in the computer Input.
HighMid
Low
High
Adj.
Color temp.
Appendix
Color
management
Auto picture 
control
Off/L1/L2
XLowLowMid
Color temp.
Offset
Red/Green/Blue/Quit
Image 10
Color
Gamma
ListColor M.
MenuMid
Low
Color M.
All DelMenu
Lamp control
Go to System (2)
Shutter management Remote Control
5 - 180 Min
PIN code lock
Input 4(For Optional Interface Boards)
(For Optional Interface Boards)
Go to System (1)
High
Color temp.Off/AutoAdvanced color 
						

							70
Computer Input
System (1)Mode 1
Mode 2Image SelectStandard
Real
Image 1
Image 10
ScreenNormal
True
Wide
Full screen
Digital zoom +
Digital zoom -PC AdjustAuto PC adj.
Fine sync.
Total dots
Position H
Position V
Clamp
Display area - H
Display area -  V
Reset
Mode free
Store
Quit
0–31
Yes/No
Mode 1
Mode 10
Quit
✽ System displayed in the System Menu varies depending on the input signal.
✔Note:
•The Menu display varies depending on the input signal.
SVGA 1
SVGA 2
SVGA 3
Rear
Keystone
Ceiling Reset
StoreOn/Off
On/Off
CustomH & VScale
Position H / VOn/OffH / VCommon
Reset
Video Input
System (2)Auto
PAL
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
System (3)Auto
1080i
1035i
720p
575p
480p
575i
480i
Image SelectStandard
Cinema
Image 1
Image 10ScreenNormal
Wide
Rear
Keystone
Ceiling
Reset
StoreOn/Off
On/Off
Custom
H & V
Scale
Position H / VOn/OffH / VCommon
Reset
Reset
Reset
Appendix
Quit
Quit
Quit
Quit
Yes/No Yes/No
Current modeH-sync freq.
V-sync freq.
Quit