Sanyo Plc Ef60 Projector User Manual

							71
Appendix
No sound–  Check audio cable connection from audio input source.
–  Adjust the audio source.
–  Press the Volume (+) button.  (
☞page 33)
–  Press the Mute button.   (☞page 33) 
Some displays are not seen–Check the Display item.  (
☞“Setting” on page 54)
during  the Operation.
Only part of image is displayed.–Check if you are in D. Zoom+/–  mode.  (
☞page 33, 49)
(Large/Small)–Change Aspect setting in the Screen setting menu.  (
☞page 48)
–Adjust Display area and Position in the PC adjust menu.  (☞page 42–43)
PIN code dialog box appears at start-up.–PJPIN code lock is being set.  Input a PIN code (1234 or numbers you have 
set).  (☞“Enter a PJ PIN Code” on page 28 and 57)
Image is not displayed on the –Select Input 1 with the Input button on the top control or the INPUT 1 button
monitor connected to the ANALOGon the remote control, or through the Input Menu.  (
☞page 31and 37)  
OUT terminal.–Make sure Analog out is On.   (☞ Setting on page 55) 
The Top Control does not work.–Check if the Keylock function is set.  (☞Setting on page 56)  
The Wireless Remote Control –Check the batteries.  When replacing, the two batteries should be replaced  
does not work.at the same time.  (
☞page 17)
–Make sure no obstruction is between the projector and remote control.
–Make sure you are not too far from the projector when using the remote 
control.  Maximum operating range is 32.8’ (10m).
–Make sure the ID and CH of the remote control is conformed to the 
projector.  (
☞page 16 and 53)
–Initialize the remote control ID and CH, and then initialize the remote control 
ID and CH of the projector as well.  (
☞page 16 and 53)
–Unlock Key lock for the remote control in the Setting Menu.  (
☞page 56)
–Make sure the wired remote cable is not connected to the projector. 
(
☞page 26)
When all the solutions above fail, try Factory default in the Setting menu.  
(☞page 58)
USB mouse does not operate properly. –Check cable connection of the USB mouse and the projector.   (☞page 26)
SHUTTER button does not operate. –Make sure Shutter protection is Off.   (☞Setting on page 55)
Lens position moves when Input –Check Lens memory for each input.   (
☞Setting on page 55)
is switched.
Some operating menu items do not appear.–Check the My menu setting.   (☞Setting on page 51)
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
If problems still persist after following all operating instructions,
contact the dealer where you purchased the projector or the
service center.Give the model number and explain about the problem.  We will advise you how to obtain service.
Appendix 
						

							72
Appendix
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 230 MHz of Dot Clock.
–––––––– 
(Interlace)
1024 x 768
(Interlace)
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
MAC 191024 x 76860.2475.08
MAC 211152 x 87068.6875.06
UXGA 31600 x 120087.5070.00
UXGA 41600 x 120093.75075.00
SVGA 1800 x 60035.15656.25
SVGA 2800 x 60037.8860.32
SVGA 3800 x 60046.87575.00
SVGA 4800 x 60053.67485.06
SVGA 5800 x 60048.0872.19
SVGA 6800 x 60037.9061.03
SVGA 7800 x 60034.5055.38
SVGA 8800 x 60038.0060.51
SVGA 9800 x 60038.6060.31
SVGA 11800 x 60038.0060.51
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
XGA 111024 x 768
XGA 131024 x 768
XGA 141024 x 768
61.0075.70
XGA151024 x 768
46.9058.20
XGA 81024 x 768
47.0058.30
XGA 91024 x 768
(Interlace)
58.0372.0
SXGA 11152 x 864
SXGA 21280 x 1024
63.4879.35
SXGA 31280 x 1024
36.0087.17
SXGA 41280 x 1024
64.2070.40
SXGA 51280 x 1024
62.5058.60
SXGA 61280 x 1024
63.9060.00
SXGA 71280 x 1024
63.3459.98
SXGA 81280 x 1024
63.7460.01
SXGA 111152 x 900
71.6967.19
SXGA 121152 x 900
81.1376.107
SXGA 131280 x 1024
(Interlace)
63.9860.02
SXGA 141280 x 1024
(Interlace)
61.2065.20
71.4075.60
50.0086.00
720p–––––––– 
(Progressive)
50.0094.00
45.0060.00
XGA 11024 x 768
XGA 21024 x 768
XGA 31024 x 768
XGA 41024 x 768
48.3660.00
68.67784.997
XGA 61024 x 768
60.02375.03
XGA 71024 x 768
56.47670.07
48.5060.02
44.0054.58
SXGA 91280 x 1024
SXGA 101280 x 960
79.97675.025
60.0060.00
SXGA 151280 x 1024
SXGA 161280 x 1024
SXGA 171152 x 900
SXGA 181280 x 1024
(Interlace)
63.3760.01
76.9772.00
61.8566.00
46.4386.70
SXGA 191280 x 102463.7960.18
XGA 51024 x 76860.3174.92
VGA 7640 x 48043.26985.00
575i–––––––– 
(Interlace)15.62550.00
480i–––––––– 
(Interlace)15.73460.00
1080i/60–––––––– 
(Interlace)33.7560.00
1035i–––––––– 
(Interlace)33.7560.00
SVGA 10800 x 60032.7051.09SXGA 201280 x 102491.14685.024
480p–––––––– 
(Progressive)31.4759.88
XGA 101024 x 76862.0477.07
1080i/5028.12550.00
SXGA 211400 x 105063.9060.00
MAC1280 x 96075.0075.08
UXGA 11600 x 120075.0060.00
UXGA 21600 x 120081.2565.00
XGA 1235.52286.96
575p–––––––– 
(Progressive)31.2550.00
MAC1280 x 102480.0075.08
WXGA 31376 x 76848.3660.00
WXGA 41360 x 76856.1672.00
WXGA 11366 x 76848.3660.00
WXGA 21360 x 76847.7060.00
Compatible Computer Specifications 
						

							73
Appendix
Proper image may not be obtained in some signals.  Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
D-VGA640 x 48031.4759.94
D-480p720 x 480
(Progressive)31.4759.88
D-575p768 x 575
(Progressive)31.2550.00
D-SVGA800 x 60037.87960.32
D-XGA1024 x 76843.36360.00
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
D-SXGA11280 x 102463.9860.02
D-SXGA21280 x 102460.27658.069
When a input signal is digital from DVI terminal, refer to chart below.
D-WXGA11366 x 76848.3660.00
D-WXGA21360 x 76847.7060.00
D-WXGA3 1376 x 76848.3660.00
D-UXGA1600 x 120075.0060.00
Appendix
D-720p1280 x 720
(Progressive)45.0060.00
D-1035i1920 x 1035
(Interlace)33.7560.00
D-1080i/601920 x 1080
(Interlace)33.7560.00
D-1080i/501920 x 1080
(Interlace)28.12550.00 
						

							74
Appendix
Technical Specifications
Mechanical Information
Projector Type Multi-media Projector
Dimensions (W x H x D) 20.39 x 9.92 x 23.86 (518mm x 252mm x 606mm) (Not including adjustable feet)
Net Weight 54.3 lbs (24.7kgs)
Feet Adjustment 0˚ to 3.65˚
Panel Resolution PLC-XF60 PLC-EF60
LCD Panel System 1.4 TFT Active Matrix type, 3 panels
Panel Resolution 1024 x 768 dots 1400 x 1050 dots
Number of Pixels 2,359,296 (1024 x 768 x 3 panels) 4,410,000 (1400 x 1050 x 3panels)
Signal Compatibility
Color SystemPAL, SECAM, NTSC, NTSC4.43, PAL-M, PAL-N
High Definition TV Signal480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
Scanning FrequencyH-sync. 15 ~ 120 KHz, V-sync. 48 ~ 120 Hz
Optical Information
Projection Image Size (Diagonal) Subject to Optional lens
Projection Lens Option
Throw Distance Subject to Optional lens
Projection Lamp 300W
Interface
Input 1 terminals DVI-D Terminal (Digital in) (HDCP Compatible) x1, (VGA) HDB15 Terminal X 2  (Analog In/ 
Analog Out) and Mini Jack (stereo) x 1
Input 2 terminals BNC Type x 5 (G/ VIDEO/Y, B/ Cb/Pb, R/ Cr/Pr, H/V, V) and Mini Jack (stereo) x 1
Input 3 terminals RCA Type x 3 (VIDEO/Y, Cb/Pb, Cr/Pr), Mini DIN 4 pin x 1 (S-Video) and RCA Type x 2 
(Audio R and L(mono))
Input 4 terminals DVI-D Terminal (Digital in) (HDCP Compatible) x1, Serial port In (DB9) x 1 and 
Serial port Out (DB9) x1
Other 
Terminals
SERIAL PORT IN
DB9 pin x 1
SERIAL PORT OUT DB9 pin x 1
USB Connectors USB Series A receptacle x 1 and USB Series B receptacle x 1
R/C Jack Mini Jack  x 1  
Audio
Internal Audio Amp 3.0W RMS
Built-in Speaker 2 speaker, ø2.05 (52mm) 
Power
Voltage and Power Consumption AC 100 ~ 120 V (9.5 A  Max. Ampere), 50 / 60 Hz  (The U.S.A and Canada)
AC 200 ~ 240 V (4.5 A  Max. Ampere), 50 / 60 Hz  (Continental Europe and The U.K.)
Operating Environment
Operating Temperature 41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
Storage Temperature 14 ˚F ~ 140 ˚F (-10˚C ~ 60 ˚C)
Remote Control
RF Remote Standard  2.4 GHz Low Power Radio 
Frequency Band 2.472GHz (CH1: default setting), 2.403GHz (CH2), 2.446 GHz (CH3), and 2.421GHz (CH4)
Battery AA, UM3 or LR6 1.5V  ALKALINE Type x 2
Operating RangeWithin 32.8 (10m)
Dimensions 2.0” x 1.2” x 7.1” (50mm x 30mm x 181mm)
Net Weight 0.33 lbs (150 g) (including batteries) 
						

							75
Appendix
Model No.
SCART-VGA Cable:POA-CA-SCART
Projector USB Key:POA-USB01
Smoke Resist Box:POA-SR-140
Wired Remote Cable (30m):POA-CA-RC30
Optional Interface Board Model No.
Advanced Network : POA-MD19NET  (Option Control No. 06)
Dual SDI: POA-MD17SDID
Faroudja: POA-MD09VD3
DVI (HDCP compatible): POA-MD18DVI
D-Sub: POA-MD04VGA
The parts listed below are optionally available.  When ordering those parts, give the item name, Model No. and Option
Control No. (if necessary) to the sales dealer.
Optional Parts
(This cable is used for RGB Scart 21-Pin
Video output of video equipment.)
Accessories
Owners Manual
AC Power Cord
Remote Control and Batteries
DVI-D Cable
VGA Cable
Wired Remote Cable
Lens Attachment 
Light Block Plates (2types)
Advanced Screen Manager (CD-ROM)
Real Color Manager Pro (CD-ROM)
Protective Dust Cover
Cord Cover Strap
Security Label (PIN Code/USB Key)
●The specifications are subject to change without notice.
●LCD panels are manufactured to the highest possible standards.  Even though 99.99% of the pixels are effective,  a tiny fraction of
the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
●The On-Screen Menu and figures in this manual may differ slightly from the product.  
Appendix 
						

							76
Appendix
System (1)
Input 2
Video
System (1)
Input 1
RGB 
INPUT
(2)SYSTEMSYSTEM
XGA 5
Mode 1
XGA 1
XGA 3
Auto PC adj.
Fine sync
Total dots
Current mode
Clamp
Position
Display area
Store
Quit
0 - 31
V
Yes/No
(1)
SECAM
NTSC
Auto
PAL
PAL-M
PAL-N
NTSC4.43
Quit
H
Reset
System (2)
Input 3System (2)
System (3)
Auto
Mode
Menu Tree
RGB (PC Analog)
RGB (Scart)
RGB (PC Digital)System (1)
RGB (AV HDCP)System (1)
Video
Y, Pb/Cb, Pr/Cr
Y, Pb/Cb, Pr/CrSystem (3)
S-Video
Input 4Warp & Blending Board
Input 5Optional Slot
Quit
✽Systems displayed in the System Menu vary
depending on an input signal.
SCREEN
SETTINGScreen
Wide
True
Normal
Scale
Position
Full screen
H
V
H
V
PC ADJ.
Off/OnCeiling
Off/OnRear
Quit
D. Zoom+/D. Zoom–
Keystone
Width
Phase
V
H
0 - 15
SOUND
Mute
Quit
Volume
Off/On
0 - 63
Treble-15 ~ +15
Bass-15 ~ +15
Custom
H&V
Common
ResetYes/No
Quit
D. Zoom
(3)SYSTEM
1035i
720p
Auto
1080i
480p
575i
575p
480i
System (1)
Quit
V sync. phase
Yes/No
Store/ResetFree 
						

							77
Appendix
LanguageSETTING
Power management
Remote control code
Key lock
Contrast
Brightness
Color
Red
Green
Blue
Sharpness
Store
Quit
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 15
Image 1
Image 2
Image 3
Image 4
Image 5
Tint0 - 63
Gamma
Noise reduction
0 - 15
Off
ResetYes/No
FilmOff/On
ProgressiveOff/On
Color temp.
Image 6
Image 7
Image 8
Image 9
Image 10Quit
Standard (AV)
Standard (PC)RealImage 1Image 2Image 3
IMAGE 
Image 4
Cinema
Image 5Image 6Image 7
Image 8
Image 9
Image 10
Quit
IMAGE
ADJ.
Color management
Gamma
All Del
Menu
Color. M
L1
Auto picture control
L2
Off
Low
Mid
XLow
L2
L1
Menu
Off/Ready/Shut down
CH 1– 4
Remote control
Off
Projector
ID 1– 8
1 ~ 60 minutes 
Yes/No
EnglishGermanFrenchItalianSpanishPortugueseDutchSwedish
ChineseKoreanJapanese
Russian
Position
Simple menu
My menu
Factory default
Off/On
LogoLogo select
CaptureYes/No
Default
Off
My logo
LockOff/On
PIN code change
BackgroundBlue
Black
My logo
LampControl
Mode2-Lamp
1-Lamp
Normal
Eco
Auto
DisplayOff/On
Input searchOff/On
On startOff/On
Analog outOff/On
Lens memoryInput 1–5Off
Memory
ShutterLevel
Remote control
Normal
High contrast
Protection
5 ~ 180 minutesManagement
Security
On 2
Off
PJ lockOn 1
RegistrationDelete
USB LockSetting
PJ PIN code change
On 2Off
On 1
Lamp1Lamp2
Auto
Color
Appendix
High
Projector
The other USB
The USB plugged in
Color. M
Menu
List 
						

							78
Appendix
Input
SignalScreenLanguageLamp modeLamp status
INFORMATION
Power management
System
Shutter managementSmoke resistOption filter time
Security
Remote control 
Quit
LampSPECIAL
Quit
Filter 
Lamp 1
Lamp 2
Option box
RS–232CBaud rate
Projector ID
9600
19200
Warning log
USB memoryPC modeSave
Delete
Load
W
Reset
Hour(s)
Yes/No
W
Reset
Hour(s)
Yes/No
Fan control
Max
Hour(s)
Reset
Hour(s)
Reset
Yes/No
Yes/No
001 – 999
USB memory 1–10
Quit
Projector
USB memory 1–10
Quit
USB memory 1–10Quit
Image adj.Save
Load
USB memory 1–10
Quit
USB memory 1–10
USB memory 1–10
Quit
Quit
Normal
Delete
Auto PC adj.Off/On
Test patternCross 1 (W)
Cross 3 (G)
Cross 2 (R)
Cross 4 (B)
Cross 6 (C)
Cross 5 (M)
Cross 7 (Y)
Color 
Gradation 1~4
Flat 1~8
DefaultYes/No 
						

							79
Appendix
20.39 (518)
23.86 (606) Unit : inch (mm)
3.65˚ (Max.) 9.92 (252)7.24 (184)
5.28 (134)
Dimensions
1.08 (27.5)
Appendix
18.11 (460)
13.58 (345)
18.27 (464)
9.15 (232.5) 9.15 (232.5) 15.91 (404)
2.36 (60)
Screw Holes for Ceiling Mount
Screws: M8
Depth: 0.31(8.0) 
						

							80
Appendix
Terminal Configurations
Terminal : DIB 9-PIN
354217986
SERIAL PORT IN /OUT TERMINAL ANALOG INPUT / OUTPUT TERMINAL (ANALOG)
Terminal : HDB15-PIN 
512341096781514131112
USB CONNECTOR (Series B)
-----
R X D
T X D
-----
GND
-----
-----
-----
Serial
1
2
3
4
5
6
7
8
Red (R/Cr) Input / Output
Ground (Horiz.sync.)
Green (G/Y) Input / Output
-----
Blue (B/Cb) Input / Output
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
-----
Horiz. sync. Input/Output (Composite H/V sync.)
Ground (Vert.sync.)
-----
Ground /  -----
Vert. sync.
-----
9
13
10
12
11
14
15
1917
21018
31119
41220
51321
61422
71523
81624
T.M.D.S. Data2–
No Connect
T.M.D.S. Data2+
No Connect
T.M.D.S. Data2 Shield
DDC Clock
DDC Data
No Connect
1
5
2
4
3
6
7
8
T.M.D.S. Data1–
No Connect
T.M.D.S. Data1+
No Connect
T.M.D.S. Data1 Shield
+5V Power
Ground (for +5V)
Hot Plug Detect
9
13
10
12
11
14
15
16
T.M.D.S. Data0–
No Connect
T.M.D.S. Data0+
No Connect
T.M.D.S. Data0 Shield
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
17
21
18
20
19
22
23
24
DVI-D TERMINAL (DIGITAL) 
Terminal : DVI-D
-----9
Vcc
- Data
+ Data
Ground
1
2
3
4
2
341
Series B