Home > Sanyo > Projector > Sanyo LNS-T30KS/W30KS, LNS-T30KB/W30KB Parts Manual

Sanyo LNS-T30KS/W30KS, LNS-T30KB/W30KB Parts Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Sanyo LNS-T30KS/W30KS, LNS-T30KB/W30KB Parts Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Following checks and confirmations should be taken for safety.
    Check the following things by the time of the cabinet assembly after the lens
    replacement.
    1. Confirm the lens is securely fixed by 4 screws.
    2. Confirm the proper wiring and the wires are fixed properly.
    3. Confirm the each connector is connected properly.
    4. Wiring must not be tangled in the mechanical parts.
    5. There is no missing part, or no loosing mounting part.
    LCD PROJECTOR LENS
    MODEL LNS-T30KS/W30KS
    LENS REPLACEMENT PROCEDURE
    NOTES ON LENS REPLACEMENT
    Lens replacement should be performed by the qualified service personnel.
    It should be followed by this procedure precisely.
    Before attempt to replace the lens, confirm the model number (both the LCD
    projector and the lens) and use the proper lens.
    If you have any questions, contact to the dealers.
    Following parts are contained in the packing.
    1AA6P1P2279-- (ICSZ)
    The focus and zoom of this lens cant be adjusted by controls on main cabinet or the
    remote control unit.
    LNS-T30KB/W30KB
    
    PARTS LIST
     LENS
     FRONT CABINET
     WIRE BAND1 piece
    1 piece
    1 piece 
    						
    							Remove 4 screws on side cabinet and 1 screw
    on rear.
    Grasp the two sides, pull the cabinet top
    upward and remove.
    LENS REPLACEMENT PROCEDURE
    REMOVE THE CABINET TOP (See figure-1)1
    1.
    2.
    2
    Fig-1
    REMOVE THE CABINET FRONT (See figure-2)
    Remove 2 screws on cabinet front bottom.
    Grasp the two sides, pull the cabinet front
    forward and remove.
    Remove 2 speaker connectors, LED
    connector K8K,  remote control pre-amp.
    connector K18D and remove the cabinet
    front completely.1.
    2.
    3.
    Fig-2
    3REMOVE THE LED UNIT AND SPEAKERS (See figure-3)
    Release two hooks and pull out the LED unit.
    Remove 4 screws and then remove the
    speakers.1.
    2.
    Fig-3
    MOUNT T THE LED UNIT AND SPEAKERS4
    CABINET TOP
    SPEAKER CONNECTORS
    REMOTE CONTROL PRE-
    AMP. CONNECTOR K18D
    CABINET FRONT
    LED CONNECTOR K8K
    SPEAKERS
    LED UNIT
    Mount the LED unit and speakers to the new
    cabinet front.
    Perform the stepstofor lens replacement.
    110
    HOOKS 
    						
    							Remove 7 screws-A, 2 screws-B and
    disconnect the 3 FPC cables of LCD panels.
    Grasp the two sides, pull the Main unit upward.
    Disconnect the lens motor connector K16S
    from the circuit board.
    REMOVE THE LENS MOTOR CONNECTOR (See figure 4, 5)5
    1.
    2.
    3.
    Fig-4
    A
    A
    A
    A
    AAA B
    B
    Cut the wire band and remove the
    lens motor lead.
    LENS MOTOR CONNECTOR K16SLENS MOTOR CONNECTOR K16S
    Fig-5
    FPC CABLE REMOVAL
    CONNECTOR
    FPC
    CABLE
    CABLE
    LOCK
    When disconnecting the FPC cable, pull out
    the cable lock from the connector and then
    disconnect the FPC cable.
    Connector position is different depend
    on the models. (See figure-5)NOTE: 
    						
    							MOUNT THE CABINET TOP (See figure-9)
    1.
    2.
    8
    Fig-9
    MOUNT THE MAIN UNIT (See figure-8)
    Mount the main unit with 7 screws-A, 2
    screws-B and connect the 3 FPC cables.
    Fig-8
    9MOUNT THE CABINET FRONT (See figure-8)
    10
    Remove 4 screws and pull out lens from lens
    mounting bracket. Be careful not to drop the
    lens when removing it.
    REMOVE THE LENS (See figure-6)6
    Fig-6
    Remove the protective cover on the replacing
    lens.
    Insert the lens to the lens mounting bracket
    and fasten it with the four screws. Use the
    screws included with the lens to fastening
    them.
    MOUNT THE LENS (See figure-7)7
    1.
    2.
    Fig-7
    LENS MOUNTING BRACKET
    Connect 2 speaker connectors, LED connector
    K8K and remote control pre-amp. connector
    K18D.
    Mount the cabinet front with the 2 screws.
    Mount the cabinet top with the 5 screws. 
    						
    							†
    ¶whŠz
    žcmWw:Uq¬Ý›æloXi^M{
    èﶦõwKqz©ßÏÉ¿Ä›
    ʈqo”‡QtzmWw:U›æl
    oXi^M{
    èï¶UŠwµ«æá”p`lT“{^•oM”T{
    
    
    ¢U
    Y`X昕oM”Tz‡h
    
    ¢w
    TU
    Y`X昕oM”T{
    ¤
    €¯É«»”xz`lT“x‡loM”T{
    
    
    ¢Uݧ
    æ
    ¼tT’‡loMsMT{
    Ž•oM”
    æ
    ¼xsMT{
    ÷	¥Óé´£«»”èï¶
    
    
    						
    							èﶦõS‘|	“
    ÇZx
    	Í
    æ©ßÏÉ¿ÄØ¢Š£z™Ø¢Š£wµ«æá
    ”›Ž`‡b{
    	Í
    æ©ßÏÉ¿Äw†± Å›Ëloz	ÍtËj	Í[”
    ‘OtŽ`‡b{
    èﶦõw`Th
    	Í
    æ©ßÏÉ¿Ä›Žb{¢
    $
    €	°£
    
    
    ™
    
    w		qpæM‡b{
    
    $
    
    ²Ø©ßÏÉ¿Ä›Žb{¢
    $€	°£
    
    ²Ø©ßÏÉ¿ÄwØwµ«æᔢŠ£›Ž`‡b{
    
    ²Ø©ßÏÉ¿Äw†± Å›Ëloz	
    ²t¾Á”‘
    OtŽ`‡b{
    
    						
    							µ«æá” ¢Š£zµ«æá” #¢Š£t|
    -$%ÍÉçw1$­”Òç¢U	t£›Ž`‡b{
    Ý ïâÇ¿Äw†± Å›ËlozT”X	ÍtËj
    	Í[‡b{
    èï¶Þ”»”w¯É«»” ,4›Ž`‡b{
    ¢
    $€	°£
    èï¶Þ”»”w¯É«»”›Žb{
    						
    All Sanyo manuals Comments (0)

    Related Manuals for Sanyo LNS-T30KS/W30KS, LNS-T30KB/W30KB Parts Manual