Sanyo LNS-T03 Installation Manual

							LENS REPLACEMENT AND INSTALLATION PROCEDURE{Type (1) Cabinet}
-2-
1
Remove 2 Screws A and Remove Lower Lens
Cover. Push part B and pull the Lower Lens
Cover down and remove it. (See Fig. 1.)
2  
Remove 4 Screws C. Pull the Upper Lens Cover
toward front and remove it. (See Fig. 2.)
3  
Remove 2 Screws D and Cover Plate from the
back of the Upper Lens Cover. (See Fig. 3.)
A
C
C
B
Fig-3
Fig-1
Fig-2
UPPER LENS
COVER 
COVER PLATE
UPPER LENS
COVER 
LOWER LENS
COVER 
D 
						

							-3- LENS LOCK RELEASE
Fig-4
LENS LOCK 
4  
Remove Lens Protection Cap from the rear (mounting side) of the Projection Lens and attach the
lens Attachment to the lens with 4 Screws. (Use screws attached to the lens.) See Fig. 4.
5  
Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6)
Mount the Lens into the lens mounting bracket and grasp the lens lock lever and turn it counter-
clockwise until the lever is locked. (See Fig. 5 and 7)
After installing the lens, make sure the lens is not loose and properly installed.
Grasp (unlock)
Lens Lock Lever
and pulling
upward.
Grasp (unlock) Lens
Lock Lever and fully
pulled downward until it
is locked (clicked).
Fig-6Fig-7
LENS ATTACHMENT
Lens Attachment 01
POA-LNA-01
(610 303 8742)
Part No. (610 275 6029)DRIVER INCLUDED 
IN THE LENS PACKAGELENS LOCK
LEVER
Fig-5
LENS INSTALLATION NEEDS TWO OR MORE PEOPLE.
TO INSTALL THE LENS BY A SINGLE PERSON MAY RESULT IN A SERIOUS DAMAGE
ON THE LENS OR THE PROJECTOR BY DROPPING OR BUMPING THE PRODUCTS.
6  
Set up the projector and project image on the screen. Turn the lens part A to adjust ZOOM. Turn
the lens part B to adjust FOCUS.
Turn the lens part A
to adjust ZOOM.
Turn the lens part B
to adjust FOCUS.
A
B
LENS MOUNTING
BRACKET 
						

							-4-
7  
Put back the Upper Lens Cover to the projector and Fix the Upper Lens Cover with 4 Screws C.
(See Fig. 2.) Put back the Lower Lens Cover to the projector. Fix the Lower Cover with 2 Screws A.
(See Fig. 1.)
Fig-8
LOWER LENS
COVER 
UPPER LENS
COVER  
						

							LENS REPLACEMENT AND INSTALLATION PROCEDURE{Type (2) Cabinet}
-5-
2  
Remove 4 Screws C. Pull the Lower Lens Cover
toward front and remove it. (See Fig. 2.)
3  
Remove 2 Screws D and Cover Plate from the
back of the Upper Lens Cover. (See Fig. 3.)
Fig-1
UPPER LENS
COVER 
Fig-2
LOWER LENS
COVER 
C
COVER PLATE
UPPER LENS
COVER 
D
Fig-3
C
B
A
1
Remove 2 Screws A and Remove Upper Lens
Cover. Push part B and pull the Upper Lens
Cover up and remove it. (See Fig. 1.) 
						

							-6-
LENS LOCK RELEASE
Part No. (610 275 6029)Fig-4
LENS LOCK 
4  
Remove Lens Protection Cap from the rear (mounting side) of the Projection Lens and attach the
lens Attachment to the lens with 4 Screws. (Use screws attached to the lens.) See Fig. 4.
5  
Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6)
Mount the Lens into the lens mounting bracket and grasp the lens lock lever and turn it counter-
clockwise until the lever is locked. (See Fig. 5 and 7)
After installing the lens, make sure the lens is not loose and properly installed.
Lens Attachment 01
POA-LNA-01
(610 303 8742)LENS ATTACHMENTLENS LOCK
LEVER
Fig-5
Fig-6Fig-7
Grasp (unlock) Lens
Lock Lever and fully
pulled downward until
it is locked (clicked).
Grasp (unlock)
Lens Lock Lever
and pulling
upward.
LENS INSTALLATION NEEDS TWO OR MORE PEOPLE.
TO INSTALL THE LENS BY A SINGLE PERSON MAY RESULT IN A SERIOUS DAMAGE
ON THE LENS OR THE PROJECTOR BY DROPPING OR BUMPING THE PRODUCTS.
A
B
6  
Set up the projector and project image on the screen. Turn the lens part A to adjust ZOOM. Turn
the lens part B to adjust FOCUS.
Turn the lens part A
to adjust ZOOM.
Turn the lens part B
to adjust FOCUS.
DRIVER INCLUDED 
IN THE LENS PACKAGE
LENS MOUNTING
BRACKET 
						

							-7-
Fig-8
LOWER LENS
COVER 
UPPER LENS
COVER 
7  
Put back the Lower Lens Cover to the projector and Fix the Lower Lens Cover with 4 Screws C.
(See Fig. 2.) Put back the Upper Lens Cover to the projector. Fix the Upper Cover with 2 Screws A.
(See Fig. 1.)