Home > Sanyo > Projector > Sanyo LNS-T01z, LNS-w01z Installation Manual

Sanyo LNS-T01z, LNS-w01z Installation Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Sanyo LNS-T01z, LNS-w01z Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							1AA6P1P2629--  (ICPWZ)
    ÷	¥Óé´£«»”èï¶
    
    
    						
    							èï¶w	“
    ÇZz‡hx¦õwKqtzS–Mts’sM
    æ
    ¼U’”	ÔùUK“‡b{
    \•’w
    æ
    ¼x™Ô
    žAqs”	ÔùUK“‡bwpzG
    ~t-`oXi^M{
    Þ
    †Ì¤w
    $xîMw‹wqŸs”	ÔùUK“‡b{
    	“
    ÇZ^À	Íw«™
    \wèï¶xzæÞ¯ï‡hx÷	¥Óé´£«»”Š.pw¶”ÜS‘|Ñ¥”§
    µÐ
    TxpV‡dœ{
    Ô èï¶w	“
    ÇZz¦õ^Àx±”ϵU	[»UæloXi^M{
    Ô èï¶w	“
    ÇZz¦õ^Àx\w^À		q	{t`hUMz
    Y`XæloXi^
    M{
    Ô èï¶txèï¶-¢whŠw©ß¿ÓU
    ÇMoM‡b{èﶛ	“
    ÇZ”‡
    QtzTs’c©ß¿Ó›xc`oXi^M{
    Ô èï¶w	“
    ÇZz	“Ž`wqVzèï¶w
    ¯Ø›	p^˜lh“	‡›
    ÇZh
    “`sM‘O]«™Xi^M{
    èﶛ	“
    ÇZhKqzèﶧ̔›	“
    ÇZ”‡QtzmWw:U›ælo
    Xi^M{
     
    						
    							 
    						
    							
    ÇÅå Ì”
    èï¶Ú¢ïÄÒå­¿Ä
    
    $
    èﶛ	“
    ÇZ‡b{¢
    $€	°£
     xa
    						
    							LCD PROJECTOR LENS
    MODEL NO. LNS-W01Z / LNS-T01Z
    LENS REPLACEMENT 
    AND INSTALLATION PROCEDURES
    NOTES ON REPLACEMENT AND INSTALLATION
    The procedures and the needed pars for lens installation depend on the type of
    cabinet.  Before installing or replacing the lens, make sure the type of cabinet and be
    sure to refer to the Installation Manual corresponding with your projector.
    When installing or replacing the lens, make sure the Lens Model No. matches with
    your projector.  Refer to the catalog, or contact your sales dealer for the proper Lens
    Model No.
    TYPE OF THE CABINET AND REFERENCE INSTALLATION MANUAL
    Refer to the Installation Manual corresponding to your projector.  
    (See the chart below.)
    Type of the CabinetReference Installation Manual
    Refer to this manual.
    Refer to the Installation Manual
    supplied with the Projector.Other than the above cabinet
    design.  
    						
    							Some parts are not used for installation or replacement.  Keep these parts for later use.
    Note : Figures in this manual may be differ from the actual product.
    NOTES ON LENS INSTALLATION
    The ZOOM and FOCUS adjustment on the Top Control or the Remote Control can-
    not be operated with this Lens.
    • Lens installation and replacement should be made by the qualified service per-
    sonnel.
    • Be sure to install the lens following this procedure precisely.
    • The lens cover is on the lens for protection.  Be sure to replace the lens cover
    before installation.
    • When installing or replacing the lens, be careful not to stain, scratch or damage
    the lens.
    After installing or replacing the lens, be sure to check the following for safety.
    1. Check the lens is securely fixed by 4 screws.
    2. Check no wiring is tangled on the gear of lens motor or the other mechanical
    parts.
    3. Check no part is missing, or no mounting part is loose.
    BE SURE TO CHECK FOR SAFETY
    LIST OF CONTENTS
    Following parts are included in the packing.
    • LENS 1 pc.
    • LENS MOUNTING SCREWS  2 pcs. (for spare)
    • DRIVER 1 pc.
    • LIGHT-BLOCK SHEET 1 pc. 
    						
    							LENS REPLACEMENT AND INSTALLATION PROCEDURE
    1. Remove screws A (2 screws).
    2. Pull down the lower lens cover while pushing
    the part D, then remove it.
    3. Remove screws B (2 screws).
    4. Remove screws C (2 screws) and remove
    upper lens cover.
    1
    A
    Fig-1
    Fig-2
    IN CASE OF MODEL WITHOUT LENS
    Remove 2 screws and pull down the plate.
    2
    UPPER LENS COVER
    LOWER LENS COVER
    C
    B
    D
    D
    COVER PLATE
    REMOVE THE LENS COVER. (See figure-1)
    (At the step , insert the light-block sheet in
    the same position as the removed cover plate
    has been placed. Two screws are not used.)4
    REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-2)
    LENS 
    MOTOR LEAD
    CONNECTOR “ K16B”
    (D)
    (D)(D)
    (D)
    B
    A
    LENS MOTOR
    Fig-3
    ❋Figure shown inside of the cabinet.
    REMOVE THE LENS. (See figure-3.)
    1. Remove the connector “K16B” of the
    circuit board.
    2. Loosen the A, B wire holder and
    remove the lens motor lead.
    3. Remove screws D (4 screws) which
    fastens the lens and remove the lens.
    IN CASE OF MODEL WITH LENS
    A
    Set the light-block
    sheet, so that the
    large rounder side is
    set over the lens.
    Perform the steps  to  for lens replacement and installation.51
    SCREWS 
    						
    							MOUNT THE LENS COVER. (See figure-6)
    INSTALL THE LENS. (See figure-4)
    1. Remove protective caps(front and
    back) on the lens.
    2. Mount the lens on mounting bracket
    of the main cabinet with 4 screws.
    Use the screws included with the lens.
    Use the driver included with the lens to
    fasten the screws.
    (After using, save it for latter use.)
    3
    A
    INSTALL THE LIGHT-BLOCK SHEET. (See figure-5)4
    Install the light-block sheet around the lens
    as shown in the illustration.  Use the sheet
    included with the lens.
    When this projector permanently install in
    the structure, slide the picture, obtain cor-
    rect focus, then lock the lens by Focus Lens
    Lock screw at this step.
    1. Insert the upper part lens cover and fix
    them with screws A (4 screws).
    2. Insert the lower part lens cover and fix
    them with screws B. (2 screws).
    5
    LENS MOUNTING BRACKET
    ATTACHED DRIVER
    FOCUS LENS LOCK SCREW
    UPPER LENS COVER
    LOWER LENS COVER
    A
    B
    Fig-4
    Fig-5
    Fig-6
    When in install the both upper and lower
    lens covers, install the light-block sheet so
    that it  should be placed in the guide slot.
    (place of the cover plate had been placed.
    See figure-2.) If the installation of light-block
    sheet is incorrect, it will be the cause of
    leakage of light or the dust entering at the
    main cabinet.
    LIGHT-BLOCK SHEET
    Adjust focus by rotating
    the lens. 
    						
    All Sanyo manuals Comments (0)

    Related Manuals for Sanyo LNS-T01z, LNS-w01z Installation Manual