Sanyo Dsr 3716 P Manual

English
General settings
How to set 70
1Connect the RS-485 terminal on the rear panel of 
the DVR with the system controller (Figure 1). 
2Display the  screen as explained in 
Displaying the general settings screen, and then 
turn the S-dial clockwise. (P62)
The DATA SPEED 19200 indicator starts blinking.
3Turn the J-dial to select the desired DATA SPEED 
(example: 9600), and then turn the S-dial twice 
clockwise. 
Selections: 2400/4800/9600/19200
The OFF indicator of STATUS INFO starts blinking.
4Repeat...

English
General settings
71 How to set
The protocol (address)  and the external alarm trigger 
control settings are needed when operating the coaxial 
superimposed dome camera.
If the protocol settings are set to OFF the ALARM REC 
TRIGGER SET cannot be set.
1Connect the VIDEO IN terminal on the rear panel of 
the DVR to a remotely controllable dome camera 
using a coaxial cable. (Figure 1)
2Display the  screen as 
explained in Displaying the general settings 
screen (P62).
3Turn the J-dial to select...

English
General settings
How to set 72
Depending on the settings of the selections under 
ALARM RECORDING, the camera lens can be set to 
move to a preset position or automatic panning when an 
alarm is detected.
Confirm the ALARM RECORDING setting. (P56) 
1Display the  screen 
using Displaying the general settings screen 
(P62).
2Turn the J-dial to select ALARM REC TRIGGER 
SET and then turn the S-dial clockwise.
The  screen is 
displayed.
3Turn the J-dial to select the camera (CH) that will do 
the...

English
General settings
73 How to set
bCamera control is not possible in the following 
cases, even if the function indicator (FUNC.) is 
ON.
 While displaying menus, or the search menu
 During playback (during pause, or copy menu is 
display)
 During quad-screen, multi-screen (9/16) and plus 
screen display
 During zooming, automatic scrolling and monitor 2 
display
bIf another button is pressed while the following 
indicators are blinking (controllable state), the 
control function will be...

English
How to set 74
Screen setting
Menu configuration
                   
 CH          01  02  03  04  05  06  07  08
  MAIN MON.  OFF OFF OFF OFF OFF OFF OFF OFF
  MON.2      OFF OFF OFF OFF OFF OFF OFF OFF
  NETWORK    OFF OFF OFF OFF OFF OFF OFF OFF
 CH          09  10  11  12  13  14  15  16
  MAIN MON.  OFF OFF OFF OFF OFF OFF OFF OFF
  MON.2      OFF OFF OFF OFF OFF OFF OFF OFF
  NETWORK    OFF OFF OFF OFF OFF OFF OFF OFF
             
  CH          01  02  03  04  05  06  07  08
   MAIN MON.  ON...

English
Screen setting
75 How to set
1Display the  screen as explained in 
Displaying the screen settings, and then turn the 
S-dial clockwise. (P74)
The NORMAL field of 1. MULTI SCREEN starts 
blinking.
2Turn the J-dial, select CHANGE, and then turn the 
S-dial clockwise. 
Selections: 
NORMAL: 
No specified display positions for multi-screen 
display
CHANGE: 
Specified positions for multi-screen (quad/9/16) 
display
The cursor moves to QUAD POSITION SET. 
Turn the J-dial and select the quad, multi-9 or...

English
Screen setting
How to set 76
1Display the  screen as explained in 
Displaying the screen settings (P74). 
The cursor moves to the 1. MULTI SCREEN position.
2Turn the J-dial to select 2. SEQUENCE, and then 
turn the S-dial clockwise. 
Selections: 1/2/ ... 29/30SEC/INDIV.
The 1SEC indicator starts blinking.
After specifying the number of seconds, the cursor will 
not move to the SEQUENCE SET position. This way 
the automatic sequence will be set to the same interval.
3Turn the J-dial to select the...

English
Screen setting
77 How to set
1Display the  screen as explained in 
Displaying the screen settings (P74). 
2Turn the J-dial, select 2. SEQUENCE, and then 
turn the S-dial clockwise. 
3Turn the J-dial to select INDIV., and then turn the 
S-dial twice clockwise. 
4Turn the S-dial clockwise.
5Turn the J-dial, select INDIV. for the MAIN MON. 
FULL, and then turn the S-dial clockwise. 
MAIN MON. QUAD cannot be set to INDIV..
6Turn the J-dial to select MON.2 FULL, and then 
turn the S-dial clockwise....

English
Screen setting
How to set 78
1Set TIME PERIOD A and TIME PERIOD B using 
 (P37). 
Select TIME PERIOD A or TIME PERIOD B for 
MASK under SELECT TIME PERIOD. 
The example uses TIME PERIOD A.
2Display the  screen as explained in 
Displaying the screen settings (P74). 
The cursor moves to 1. MULTI SCREEN.
3Turn the J-dial, select 3. MASK, and then turn the 
S-dial clockwise. 
The OFF starts blinking.
4Turn the J-dial, select ON, and turn the S-dial 
clockwise. 
The cursor moves to MASK SET.
5Turn the...

English
Screen setting
79 How to set
1Display the  screen as explained in 
Displaying the screen settings (P74). 
The cursor moves to the 1. MULTI SCREEN position.
2Turn the J-dial, select 4. COLOR LEVEL SET, and 
then turn the S-dial clockwise. 
The  screen of CH01 appears, 
and the cursor moves to COLOR LEVEL. 
3Press the camera selection button (example: 7) of 
the channel where you want to adjust the color 
level, and then turn the S-dial clockwise. 
The channel switches to CH07, and the 5 field at...