Sanyo Dsr 3716 P Manual

English
Recording settings
How to set 50
This menu is used to set the desired cameras for each 
group (P-1, P-2, P-3 and P-4) for programmed recording. 
For each group, cameras are selected to enable or 
disable recording from them, and their individual 
recording rates are also set here.
After this setting is completed, the program number 
(P-1~P-4) can be selected for REC PROGRAM GROUP 
on the  screen.
1PROGRAM number
Selects the program number.
Selections: P-1, P-2, P-3, P-4
2SELECT INDIVIDUAL CAMERA...

English
Recording settings
51 How to set
This menu is used to set the start and end times for timer-controlled recording.
The following timer functions are available:
Day of the week timer-controlled recording (same 
time and same recording rate every week for the 
specified day) (P52)
Sets the timer-controlled recording for the specific day of 
the week, selected from Sunday to Saturday.
Overlapping timer-controlled recording (P53)
Repeats the same timer-controlled recording every day.
External...

English
Recording settings
How to set 52
1Display the  screen as explained in 
Displaying the recording settings screen, and 
then turn the S-dial clockwise. (P39)
The SUN field starts blinking.
2Set the timer-controlled recording.
Example: 
 WEEK: Set daily (DLY).
 START: Set 8:30am.
 STOP: Set 6:30pm.
 FPS: Set 1 FPS.
 SET: Set to ON.
1Turn the J-dial, change SUN to DLY, and turn 
the S-dial clockwise.
The hour indicator – – under START starts 
blinking.
2Turn the J-dial, set 08, and turn the...

English
Recording settings
53 How to set
1Display the  screen as explained in 
Displaying the recording settings screen. (P39)
2Set the timer-controlled recording.
Example: 
 WEEK (start): Set MON.
 WEEK (stop): Set WED.
 START: Set 10:30am.
 STOP: Set 8:30pm.
 PROGRAM: Do not set.
 FPS: Set 5 FPS.
 SET: Set ON.
1Turn the J-dial, change SAT to MON, and turn 
the S-dial clockwise.
The hour indicator – – under START starts 
blinking.
2Turn the J-dial, select 10, and turn the S-dial 
clockwise.
The...

English
Recording settings
How to set 54
1Connect an external timer device to the EXT TIMER 
IN terminal on the rear panel (Figure 1).
2Display the  screen using Displaying 
the general settings screen. (P39)
3Set the timer-controlled recording.
Example: 
 PROGRAM: Do not set (OFF).
 FPS: Set 5 FPS.
 SET: Set ON.
1Turn the J-dial to select EXT, and then turn the 
S-dial twice clockwise.
The 12.5 under FPS starts blinking.
2Turn the J-dial, select 5, and turn the S-dial 
clockwise.
The OFF indicator...

English
Recording settings
55 How to set
The following settings can be performed under the alarm recording settings.
Alarm recording (P56)
These settings control the picture quality, audio recording 
and recording rate for the alarm recording area, when an 
alarm is detected.
Pre-alarm recording (P57)
These settings control the recording rate and the 
duration for pre-alarm recording.
Alarm trigger (P57)
Selects the alarm detection method.
Motion sensor (P58)
1ALARM RECORDING
Turns alarm recording ON or...

English
Recording settings
How to set 56
1Display the  screen as 
explained in Displaying the recording settings 
screen, and then turn the S-dial clockwise. (P39)
The OFF field of ALARM RECORDING starts 
blinking.
2Set the alarm recording.
1Turn the J-dial to select ALARM RECORDING 
selection, and then turn the S-dial twice 
clockwise.
Selections: 
OFF/ENABLED/AL-REC ON TIMER/AL-REC OFF 
TIMER/OLY AL-RC ON TMR
2Turn the J-dial to select the desired PICTURE 
QUALITY, and then turn the S-dial twice...

English
Recording settings
57 How to set
1Display the  screen as 
explained in Displaying the recording settings 
screen, and then turn the S-dial clockwise. (P39)
The OFF field of ALARM RECORDING starts 
blinking.
2Set the pre-alarm recording.
1Turn the J-dial to select ENABLED for ALARM 
RECORDING, and then turn the S-dial clockwise.
The *** field of the PRE-ALARM RECORDING 
switches to OFF.
2Turn the J-dial to select PRE-ALARM 
RECORDING, and then turn the S-dial 
clockwise.
The OFF indicator of...

English
Recording settings
How to set 58
Use this screen for motion sensor setting on a live video 
screen to detect moving objects such as intruders, and 
generate alarms.
The motion sensor detects movement based on 
intensity-changes on the screen. It is necessary to use 
sensor settings that are appropriate for both the location 
of the sensor and for the observed objects.
1Cursor
The default location of the cursor is the upper left corner. 
Use the J-dial to move it horizontally.
2Sensor setting...

English
Recording settings
59 How to set
1Set TIME PERIOD A and TIME PERIOD B using 
 (P37).
2Display the  screen as 
explained in Displaying the recording settings 
screen, and then turn the S-dial clockwise. (P39)
The OFF field of ALARM RECORDING starts 
blinking.
3Display the motion sensor screen
1Turn the J-dial to select ENABLED for ALARM 
RECORDING, and then turn the S-dial clockwise.
2Turn the J-dial, select ALARM TRIGGER, and 
turn the S-dial clockwise.
Selections:
ALARM/SENSOR/ALARM AND...