Samsung SCX 4825FN User Manual

21 _Getting started
getting started
This chapter gives you step-by-step in structions for setting up the machine.
This chapter includes:
• Setting up the hardware
• System requirements
• Setting up the network • Installing the software
• Machine's basic settings
SETTING UP THE HARDWARE
This section shows the steps to set up the hardware which is explained in 
the 
Quick Install Guide . Make sure you read  Quick Install Guide and 
complete following steps.
1. Select a stable location. 
Select a...

22 _Getting started
Macintosh
Linu
x
SETTING UP THE NETWORK
You need to set up the network protocols on the machine to use it as your 
network printer. You can set up the basic network settings through the 
machine's control panel.
Supported operating systems
The following table shows the network  environments supported by the 
machine:
OPERATING  SYSTEM
REQUIREMENT (RECOMMENDED)
CPURAM
FREE HDD 
SPACE
Mac OS X 
10.3 ~ 10.4 • Intel Processor
• Power PC G4 /
G5 • 128 MB for a 
Power-PC based 
Mac...

Getting started_23
Configuring network protocol via the machine
You can set up TCP/IP network paramet ers, follow the steps listed below. 
1. Make sure your machine is connected to the network with an RJ-45 
Ethernet cable.
2. Make sure you have turned on the machine.
3. Press  Menu on the control panel, until you see  Network on the bottom 
line of the display. 
4. Press  OK to access the menu.
5. Press the left/right arrow until  TCP/IP displays. 
6. Press  OK.
7. Press the left/right arrow until...

24 _Getting started
INSTALLING THE SOFTWARE
You have to install the machine software for printing. The software includes 
drivers, applications, and other user friendly programs. 
1.Make sure that the network setup for your machine is completed. (See 
"Setting up the network" on page 22.) A ll applications should be closed 
on your computer before beginning installation.
2. Insert the Printer Software CD -ROM into your CD-ROM drive.
The CD-ROM should automatically  run, and an installation...

Getting started_25
MACHINES BASIC SETTINGS
After installation is complete, you ma y want to set the machine's default 
settings. Refer to the next section if you would like to set or change values.
Altitude adjustment
The print quality is affected by atmospheric pressure, which is determined 
by the height of the machine above sea level. The following information will 
guide you on how to set your machine to the best print quality or best quality 
of print.
Before you set the altitude value, fi nd...

26 _Getting started
Setting sounds
You can control the following sounds:
• Key Sound: Turns the key sound on or o ff. With this option set to On
, a 
tone sounds each time a key is pressed. 
• Alarm Sound: Turns the alarm sound on or off. With this option set to 
On
, an alarm tone sounds when an error occurs or fax communication 
ends.
• Speaker: Turns on or off the sounds fr om the telephone line through 
the speaker, such as a dial tone or a fax tone. With this option set to 
Comm.  which means...

Getting started_27
Using the save modes
Toner Save mode
Toner save mode allows your machine to use less toner on each page. 
Activating this mode extends the lif e of the toner cartridge beyond what 
one would experience in the normal  mode, but it reduces print quality.
1. Press  Menu until System Setup  appears on the bottom line of the 
display and press  OK.
2. Press  OK when  Machine Setup  appears.
3. Press the left/right arrow until  Toner Save appears and press  OK.
4. Press the left/right arrow...

Loading originals and print media_28
loading originals and print media
This chapter introduces you how to load originals and print media into your machine.
This chapter includes:
• Loading originals
• Selecting print media
• Changing the size of the paper in the paper tray
• Loading paper • Printing on special print materials
• Adjusting the output support
• Setting the paper size and type
LOADING ORIGINALS
You can use the scanner glass or ADF to load an original for copying, 
scanning, and sending a...

Loading originals and print media_29
2.Load the original face up into the ADF.  Make sure that the bottom of the 
original stack matches the paper  size marked on the document input 
tray.
3. Adjust the document width guides to the paper size.SELECTING PRINT MEDIA
You can print on a variety of print media, such as plain paper, envelopes, 
labels, and transparencies. Always use  print media that meet the guidelines 
for use with your machine. Print medi a that does not meet the guidelines 
outlined in...

Loading originals and print media_30
Specifications on print media
TYPESIZEDIMENSIONSWEIGHTACAPACITYB
Plain paperLetter 216 x 279 mm (8.5 x 11 inches)
• 60 to 105 g/m2 (16 to 28 lb 
bond) for the tray
• 60 to 163 g/m
2 (16 to 43 lb 
bond) for the manual tray • 250 sheets of 80 g/m
2 (20 lb 
bond) paper for the tray
• 1 sheet in the manual tray
• 250 sheets of 80 g/m
2 
(20 lb bond) paper for 
optional tray
Legal 216 x 356 mm (8.5 x 14 inches)
US Folio 216 x 330 mm (8.5 x 13 inches)
A4 210 x 297 mm (8.26...