Samsung SCX 4725FN User Manual

3.1   
3 Software overview
This chapter gives you an overview of the software that comes with your 
machine. Further details about installing and using the software are 
explained in the  Software Section .
This chapter includes:
• Supplied software
• Printer driver features
• System requirements
Supplied software
You must install the printer and scanner software using the supplied CDs 
after you have set up your machine and connected it to your computer. 
Each CD provides you with the following...

3.2   
Printer driver features
Your printer drivers support the following standard features:
• Paper source selection
• Paper size, orientation and media type
• Number of copies
In addition, you can use various special printing features. The following 
table shows a general overview of features supported by your printer 
drivers: 
FeaturePCL 6 PostScript
(SCX-4725FN only)
Windows Windows Macintosh Linux
Toner save O O
XO
Print quality 
option OOOO
Poster 
printing O
XXX
Multiple 
pages per 
sheet (N-up)...

3.3   
Linux
Macintosh 
(SCX-4725FN only)
ItemRequirements
Operating system • Red Hat 8.0 ~ 9.0 • Fedora Core 1 ~ 4
• Mandrake 9.2 ~ 10.1
• SuSE 8.2 ~ 9.2
CPU Pentium IV 1 GHz or higher
RAM 256 MB or higher
Free disk space 1 GB or higher
Software • Linux Kernel 2.4 or higher • Glibc 2.2 or higher
• CUPS
• SANE (for MFP device only)
Notes
• It is necessary to claim swap partition of 300 MB or larger for working with large scanned images.
• The Linux scanner driver supports the optical resolution at...

4.1   
4 Network setup (SCX-4725FN only)
Connecting your machine to a network is available only on the 
SCX-4725FN. This chapter gives you st ep-by-step instructions for setting 
up your machine for network connections.
This chapter includes:
•Introduction
• Supported operating systems
• Configuring TCP/IP
• Configuring EtherTalk
• Restoring the network configuration
• Printing a network configuration page
• Resetting the network interface
• Using SetIP program
Introduction
Once you have connected your...

4.2   
Static addressing
To enter a TCP/IP address from your machine’s control panel, take the 
following steps: 
1 Press  Menu until Network Setup  appears on the top line of the 
display.
2 Press the  Scroll buttons until  Config Network  appears and press 
Enter .
3 Press  Enter when TCP/IP  appears.
4 Press  Enter when  Manual  appears.
5 Press  Enter when  IP Address  appears. 
6 Enter a byte between 0 and 255 using the number keypad and 
press the  Scroll buttons to move between bytes.
Repeat this...

4.3   
2Start Windows Explorer and open the X drive. (X represents your 
CD-ROM drive.)
3Double click Application > SetIP.
4Open the language folder you want to use.
5Double click Setup.exe to install this program. 
6From the Windows Start menu, select Programs > Samsung 
Network Printer Utilities > SetIP.
7Select the name of your printer and click  . 
Note 
 If you cannot find your printer name click   to refresh the 
list.
8Enter the network cards MAC address, IP address, subnet mask, 
default gateway,...

5.1   
5 Loading originals and print 
media
This chapter introduces you to how to load originals and print media into 
your machine.
This chapter includes:
• Loading originals
• Selecting print media
• Loading paper
• Setting the paper size and type
• Verifying an output location
Loading originals
You can use the scanner glass or ADF to load an original for copying, 
scanning, and sending a fax.
On the scanner glass
Make sure that no originals are in the ADF. If an original is detected in the 
ADF, the...

5.2   
To load an original into the ADF:
1 Load the original face up into the ADF. Make sure that the bottom of 
the original stack matches the paper size marked on the document 
input tray.
2 Adjust the document width guides to the paper size.
Note 
Dust on the ADF glass may cause black lines on the printout. 
Always keep it clean.
Selecting print media
You can print on a variety of print media, such as plain paper, envelopes, 
labels, and transparencies. Always use print media that meet the...

5.3   
Supported print media types and sizes
Ty p eSizeDimensionsWeight1
1. If media weight is over 90 g/m2, use the manual tray.
Capacity2
2. Maximum capacity may differ depending on medi a weight, thickness, and environmental conditions.
Plain paper Letter 216 x 279 mm (8.5 x 11 inches) • 60 to 90 g/m2 (16 to 24 lb 
bond) for the tray
• 60 to 165 g/m
2 (16 to 43 lb 
bond) for the manual tray • 250 sheets of 75 g/m
2 
(20 lb bond) paper for the 
tray
• 1 sheet for the manual tray
Legal 216 x 356 mm...

5.4   
Media sizes supported in each mode
Guidelines for selecting and storing print media
When selecting or loading paper, envelopes, or other print materials, 
keep these guidelines in mind:
• Always use print media that conform with the specifications listed on 
page 5.3.
• Attempting to print on damp, curled, wrinkled, or torn paper can cause  paper jams and poor print quality.
• For the best print quality, use only high quality copier grade paper  specifically recommended for use in laser printers....