Samsung ML 6510ND User Manual

Network setup_ 41
request.
• DHC
Pv6 Off : Never use DHCPv6 regardless of router request.
6. Press  OK.
Manual address configuration
1. Start a web browser such as Internet Explorer that supports IPv6 
addressing as a URL (See  Connecting SyncThru™ Web Service 
on page  41 ).
 For IPv4, enter the IPv4 address (http://xxx.xxx.xxx.xxx) in the 
address field and press the Enter key or click  Go.
2. Cli
ck  Login on the upper right of the SyncThru™ Web Service web -
site.
A log-in page appears. 
3. Typ
e in...

Basic setup_ 42
4.basic setup
After installation is complete, you may want  to set the machine’s default settings. Refer to the next section if you would like 
to set or change values. This chapter gives you step-by-step instructions for setti ng up the machine.
This chapter includes:
•Altitude adjustment
• Changing the display language
• Setting the date and time
• Changing the clock mode
• Quiet Mode •
Entering characters using the number keypad
• Using the power saving mode
• Setting job time-out
•...

Basic setup_ 43
Each time you press 6, the display shows a different letter, M, N, O, m, 
n, o and finally 6.
2. To en
ter additional letters, repeat step 1.
If the next letter is printed on the sa me
  button, move the cursor by press-
ing the left/right arrow button and t hen
  press the button labeled with the 
letter you want. The cursor will move  to the right and the next letter will 
appear on the display.
You can enter a space by pressing 1 twice.
3. Whe
n you have finished entering letters,...

Media and tray_ 44
5.media and tray
This chapter provides information on how to l oad originals and print media into your machine.
This chapter includes:
•Selecting print media
• Changing the tray size
• Loading paper in tray •
Printing on special media
• Setting the default tray and paper
  
SELECTING PRINT MEDIA
You can print on a variety of print me dia, such as plain paper, envelopes, 
labels. Always use print media that meet the guidelines for use with your 
machine. 
Guidelines to select the print...

Media and tray_ 45
1.Squeeze and slide the paper width guide and paper length lever to 
locate them in the correct paper size slot marked at the bottom of the 
tray  to adjust to the paper size.
 • To adjust the tray to fit paper smaller than A5, slide the tray 
length guide inward  to A5 marked at the bottom of the tray. 
Then the handle in the middle of the paper length guide will be 
separated. Squeeze and slide the separated handle inward to 
the paper size you want.
• The duplex unit (optional for...

Media and tray_ 46
LOADING PAPER IN TRAY
Tray 1 / optional tray
1.Pull out the paper tray. And adjust the tray size to the media size you are 
loading. (See  Changing the tray size on page  44 .)
2. Flex or fan the edge of the paper  sta
 ck to separate the pages before 
loading paper.
3.  Place paper with the side you want to print facing down.
 Paper quantity indicator shows the  amount of paper in the tray. 
12
1Full
2Empty
4. Set the paper type and size for the tray. (See  Setting the default tray...

Media and tray_ 47
4.Squeeze the multi-purpose tray pa per width guides and adjust them 
to the width of the paper. Do not  force them too much, or the paper 
will bent resulting in a paper jam or skew.
5. When you print a document, set the paper type and size for the 
multi-purpose tray. For informati on about setting the paper type and 
size on the control panel (see  Setting the default tray and paper on 
page  49).
PRINTING ON SPECIAL MEDIA
The table below shows the available special media for each...

Media and tray_ 48
fusing temperature about 170°C (338 °F) for 0.1 second. The extra flaps 
and strips might cause wrinkling, creasing, or jams and may even dam -
age the fuser.
• For the best print qual ity, posi
 tion margins no closer than 15 mm from 
the edge
s of the envelope.
• Avo
id printing over the area where the envelope’s seams meet.
Transparency
To avoid damaging the machine, use on ly transparencies designed for use 
in laser printers.
• Transparencies used in the mach ine must be able to...

Media and tray_ 49
Letterhead/Preprinted paper
Single-sideddouble-sided
Tray1
Optional tray Face 
dow
nFace 
up
Multi-pur -
pose tray Face 
upFace 
down
•
Letterhead/ Preprinted paper must be pr inted with heat-resistant ink that 
will not melt, vaporize, or release hazardous emissions when subjected 
to the machine’s fusing temperature for 0.1 second. Check your 
machine’s specification to view t he fusing temperature about 170°C (338 
°F).
• Letterhea
d/ Prep
 rinted paper ink must be non-flammable and...

Media and tray_ 50
3.Right-click your machine.
4. Fo
r Windows XP/2003/2008/Vista, press  Printing Preferences.
For Windows 7 and Windows Server 2008 R2, from context menus, 
select the  Printing

 Preferences.
 If Printing Preferences  item has ► mark, you can select other 
printer drivers connect ed with selected printer.
5. Cli
ck  Paper tab. 
6. Sele
ct tray and its options, such as paper size and type.
7.Press  OK.
 If you want to use special-sized paper such as a billing paper, 
select  Paper tab >...