Samsung ML 6510ND User Manual

							Network setup_ 41
request.
• DHC
Pv6 Off : Never use DHCPv6 regardless of router request.
6. Press  OK.
Manual address configuration
1. Start a web browser such as Internet Explorer that supports IPv6 
addressing as a URL (See  Connecting SyncThru™ Web Service 
on page  41 ).
 For IPv4, enter the IPv4 address (http://xxx.xxx.xxx.xxx) in the 
address field and press the Enter key or click  Go.
2. Cli
ck  Login on the upper right of the SyncThru™ Web Service web -
site.
A log-in page appears. 
3. Typ
e in the  ID and  Password  then click  Login.
If it’s your first time logging into  Syn
 cThru™ Web Service, type in the 
below default ID and password.
• ID:  admin  
• Password:  sec00000  
4. Wh
en the SyncThru™ Web Service  window opens, click Settings 
>  Network Settings .
5. Cli
ck  TCP/IPv6 .
6. Enab
le the  Manual Address  in the TCP/IPv6  section.
 IPv6 Protocol  should be enabled.
7. Sele
ct the  Address / Prefix  and click the Add button, then the router 
prefix will automatically be entered into the address field. 
Enter the rest of addre ss. (e
 x: 3FFE:10:88:194::AAAA. “A” is the 
hexadecimal 0 through 9, A through F.)
8. Cli
ck the  Apply button.
Installing printer driver
Driver installation for network printer in IPv6 network environment is same 
as TCP/IPv4 (See  Installing network connec te
 d machine’s driver on 
page  38 ).
Select TCP/IP Port and when the list  
 of machines are displayed, simply 
select your machi nes IPv6 address.
Connecting SyncThru™ Web Service
1.Start a web browser such as Internet Explorer that supports IPv6 
addressing as a URL.
2. Click  Go 
 to access the SyncThru™ Web Service.
3. Click  Lo
 gin on the upper right of the SyncThru™ Web Service website.
A log-in page appears. 
4. Type
 in the  ID and  Password  then click Login.
If it’s your first time  log
 ging into SyncThru™ Web Service, type in the 
below default ID and password.
• ID:  admin  
• Pass
word:  sec00000  
5. Select one of th
 e IPv6 addresses (Link-local Address , Stateless 
Address,  Stateful Address , Manual Address ) from Configuration 
Report .
6. Enter the
  IPv6 addresses. (ex: http://[FE80::215:99FF:FE66:7701]) 
 
Address must be enclosed in [] brackets.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic setup_ 42
4.basic setup
After installation is complete, you may want  to set the machine’s default settings. Refer to the next section if you would like 
to set or change values. This chapter gives you step-by-step instructions for setti ng up the machine.
This chapter includes:
•Altitude adjustment
• Changing the display language
• Setting the date and time
• Changing the clock mode
• Quiet Mode •
Entering characters using the number keypad
• Using the power saving mode
• Setting job time-out
• Auto continue
• Changing the font setting
  
ALTITUDE ADJUSTMENT
The print quality is affected by atmospheric pressure, which is determined 
by the height of the machine above sea level.
Before you set the altitude value, determine the altitude where you are.
0
1High 3
2High 2
3High 1
4Normal
1. Press  Menu on the control panel.
2. Press the up/down arrow to highlight  Sy
 stem Setup and press OK.
3. Press the up/down arrow to highlight  Altitude
  Adjustmet and press OK .
4. Press the up/down arrow until the setting option you want appears.
5. Press  OK to save the selection.
6. Press  Stop/Clear
  to return to the ready mode.
CHANGING THE DISPLAY LANGUAGE
1.Press  Menu on the control panel.
2. Press the up/down arrow to highlight  Sy
 stem Setup and press OK.
3. Press the up/down arrow to highlight  La
 nguage and press  OK.
4. Press the up/down arrow to highlight the language you want.
5. Press  OK to save the selection.
6. Press  Stop/Clear
  to return to the ready mode.
SETTING THE DATE AND TIME
 •If the machine’s power is cut off, you need to reset the correct time 
and date once the power has been restored.
• Some men
u
 s may not appear in the display depending on options 
or models. If so, it is not applicable to your machine.
1. Press 
Menu  on
  the control panel.
2. Press the up/down arrow to highlight  Sy
 stem Setup and press OK.
3. Press the up/down arrow to highlight  Da
 te & Time and press  OK. 4.
Enter the correct time and date us i
 ng up/down, left/right arrow or 
numeric keypad.
5. Pres
s OK
  to save the selection.
6. Pres s Stop
 /Clear to return to the ready mode.
CHANGING THE CLOCK MODE
You can set your machine to display the current time using either a 12-hour 
or 24-hour format.
 Some menus may not appear in the display depending on options or 
models. If so, it is not applicable to your machine.
1. Press  Menu on the control pa
 nel.
2. Press the up/down arrow to highlight  Syste
 m Setup and press  OK.
3. Press the up/down arrow to highlight  Cl
 ock Mode and press  OK.
4. Press the up/down arrow until the setting option you want appears.
5. Pres s OK
  to save the selection.
6. Pres s Stop
 /Clear to return to the ready mode.
QUIET MODE
You can reduce the printing noise by turning on the  Quiet Mode. However 
the printing speed may be slowed down.
1. Pres s Menu  on the control pa
 nel.
2. Press the up/down arrow to highlight  Syste
 m Setup and press  OK.
3. Press the up/down arrow to highlight  Quiet Mode an
 d press OK.
4. Press the up/down arrow until the setting option you want appears.
5. Pres s OK
  to save the selection.
6. Pres s Stop
 /Clear to return to the ready mode.
ENTERING CHARACTERS USING THE NUMBER 
KEYPAD
As you perform various tasks, you may need to enter names and numbers.
Entering alphanumeric characters
1.When you are prompted to enter a le tter, locate the button labeled with 
the character you want. Press the bu tton until the correct letter appears 
on the display. 
For example, to enter the letter O, press 6, labeled with MNO.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic setup_ 43
Each time you press 6, the display shows a different letter, M, N, O, m, 
n, o and finally 6.
2. To en
ter additional letters, repeat step 1.
If the next letter is printed on the sa me
  button, move the cursor by press-
ing the left/right arrow button and t hen
  press the button labeled with the 
letter you want. The cursor will move  to the right and the next letter will 
appear on the display.
You can enter a space by pressing 1 twice.
3. Whe
n you have finished entering letters, press  OK.
Correcting numbers or names
If you make a mistake while entering a  number or name, press the left/right 
arrow button to delete the last digit or character.
USING THE POWER SAVING MODE
1. Press  Menu on the control panel.
2. Pre
ss the up/down arrow to highlight  System Setup and press OK.
3. Pre
ss the up/down arrow to highlight  Power Save and press OK .
4. Pre
ss the up/down arrow to select the time you want.
5.Pr
ess  OK to save the selection.
6. Pr
ess  Stop/Clear to return to the ready mode.
SETTING JOB TIME-OUT
When there is no input for a certain per iod of time, the machine cancels the 
current job. You can set the amount of  time the machine will wait before 
canceling the job.
1. Pr
ess  Menu on the control panel.
2. Pre
ss the up/down arrow to highlight  System Setup and press OK.
3. Pre
ss the up/down arrow to highlight  Job Timeout and press OK.
4. En
ter the time using up/down arrow or numeric keypad.
5.Pr
ess  OK to save the selection.
6. Pr
ess  Stop/Clear to return to the ready mode.
AUTO CONTINUE
This is the option to set th e machine to continue printing or not, in case the 
paper size you have set and the paper in the tray mismatches.
1. Pr
ess  Menu on the control panel.
2. Pre
ss the up/down arrow to highlight  System Setup and press OK.
3. Pre
ss the up/down arrow to highlight  Auto Continue and press OK.
4. Pre
ss the up/down arrow until the setting option you want appears.
•On: Automatica
 lly prints after set time passes, when the paper size 
mismatches the tray paper size.
• Off: W
aits until you press  Start on the control panel, when the paper 
size mismatches the tray paper size.
5. Pr
ess  OK to save the selection.
6. Pr
ess  Stop/Clear to return to ready mode.
CHANGING THE FONT SETTING 
Your machine has preset the f ont for your region or country.
If you want to change the font or set the font for special condition, such as 
the
  DOS environment, you can change  the font setting as follows: 1.
D
ouble-click the  Smart Panel icon on the Windows task bar (or Notifica -
tion Area in Linux). You can also click  Smart P anel on the status bar in 
Mac OS X. 
2. Click  P
rinter Setting .
3. Click  Em
 ulation.
4. C
onfirm if  PCL is selected in  Emulation Setting .
5. Click  Apply .
 Following information shows the proper font list for corresponding lan -
guages.
• Ru
ssian:  CP866, ISO 8859/5 Latin Cyrillic
• He
brew:  Hebrew 15Q, Hebrew-8, Hebrew-7 (Israel only)
• Greek
:  ISO 8859/7 Latin Greek, PC-8 Latin/Greek
• A
rabic & Farsi:  HP Arabic-8, Windows Arabic, Code Page 864, 
F
arsi, ISO 8859/6 Latin Arabic
• OCR
:  OCR-A, OCR-B
Downloaded From ManualsPrinter.com Manuals 
						

							Media and tray_ 44
5.media and tray
This chapter provides information on how to l oad originals and print media into your machine.
This chapter includes:
•Selecting print media
• Changing the tray size
• Loading paper in tray •
Printing on special media
• Setting the default tray and paper
  
SELECTING PRINT MEDIA
You can print on a variety of print me dia, such as plain paper, envelopes, 
labels. Always use print media that meet the guidelines for use with your 
machine. 
Guidelines to select the print media
Print media that does not meet the gui delines outlined in this user’s guide 
may cause the following problems:
• Poor print quality
• Increased paper jams
• Premature wear on the machine.
Pro
 perties, such as weight, compositio n,
  grain and moisture content, are 
important factors that affect the machine’s performance and the output qual -
ity. When you choose print materials, consider the following:
• The
 type, size and weight of the print media for your machine are 
describe
 d in print media specifications (See  Print media specifications 
on page  110 ).
• Desired  outcome: Th
 e print media you choose should be appropriate for 
your project.
• Bri
ghtness: Some print media are whiter than others and produce 
sharpe
 r, more vibrant images.
• Surface smoothness: The smoothness of the print media affects how 
cri

sp the printing looks on the paper.
 •Some print media may meet all of the guidelines in this section and 
still not produce satisfactory result s. This may be the result of 
improper handling, unacceptable te mperature and humidity levels, 
or other variables over which cannot be controlled.
• Befo
re purchasing large quantities of print media, ensure that it 
me
 ets the requirements  specifications in this user’s guide and 
meets your output requirements. 
 
• Using print media that does not  meet these specifications may 
cause problems, requiring repairs. Such repairs are not covered by 
the warranty or service agreements.
• Using  inflammable print media can cause a fire.
• Use desig nated prin
 t media (See Print media specifications on 
page  110 ).
 
The use of inflammable media or foreign materials left in the printer 
may lead to overheating of the unit and, in rare cases may cause a 
fire.
The amount of paper put into the tray may differ according to media type 
u s

ed (See  Print media specifications on page  110).
Media sizes supported in duplex mode
ModeSizeSource
Duplex printing
a
a. 75 to 105 g/m2 (20 to 28 lbs bond) is recommended.
For 90 to 120g/m
2 (24 to 32 lbs bond) paper, we recommend you to select 
Thick  for Paper Type  in the Printing Preferences  window (see 
Opening printing preferences on page  52).
For some models, optional duplex unit needs to be installed to use the du -
plex feature (see  Features by Models on page  25).
Letter, A4, Legal, Folio, 
Oficio
All trays
CHANGING THE TRAY SIZE
The tray is preset to Letter or A4 size, depending on your country. To 
change the size, you need to adjust the paper guides.
12
1
Paper width guide
2Paper length guide
Downloaded From ManualsPrinter.com Manuals 
						

							Media and tray_ 45
1.Squeeze and slide the paper width guide and paper length lever to 
locate them in the correct paper size slot marked at the bottom of the 
tray  to adjust to the paper size.
 • To adjust the tray to fit paper smaller than A5, slide the tray 
length guide inward  to A5 marked at the bottom of the tray. 
Then the handle in the middle of the paper length guide will be 
separated. Squeeze and slide the separated handle inward to 
the paper size you want.
• The duplex unit (optional for some models) is preset to Letter 
or A4 size, depending on your country. To change the paper 
size, adjust the guide as shown below.
•Do not push the paper width guid e too far causing the media to 
warp. 
• If you do no
t ad
 just the paper width guide, it may cause paper  jams.
2.
Flex or fan the edge of the paper stack to separate the pages before 
loading papers.
3. Place paper with the side you want to print facing down.
 Paper quantity indicator shows the amount of paper in the tray. 
12
1Full
2Empty
4. After inserting the paper into the tray, squeeze and slide the paper width 
guide and paper length guide to adjust to the paper size.
Downloaded From ManualsPrinter.com Manuals 
						

							Media and tray_ 46
LOADING PAPER IN TRAY
Tray 1 / optional tray
1.Pull out the paper tray. And adjust the tray size to the media size you are 
loading. (See  Changing the tray size on page  44 .)
2. Flex or fan the edge of the paper  sta
 ck to separate the pages before 
loading paper.
3.  Place paper with the side you want to print facing down.
 Paper quantity indicator shows the  amount of paper in the tray. 
12
1Full
2Empty
4. Set the paper type and size for the tray. (See  Setting the default tray 
and paper on page  49 .)
5. To print in application, see Basic printing on page  52. 
Multi-purpose tray
The multi-purpose tray can hold special sizes and types of print material, 
such as postcards, note cards, and envelopes. It is useful for single page 
printing on letterhead or colored paper , please check maxi mum sheets you 
can load based on thickness (See  Print media specifications on 
page  110).
Tips on using the multi-purpose tray
•Load only one type, size and weight of print media at time in the 
multi-purpose tray.
• To
 prevent paper jams, do not add p aper 
 while printing when there is 
still paper in the multi-purpose tray. This also applies to other types 
of print media.
• Alwa ys load the specified print media only to avoid paper jams and 
prin
 t quality problems. (See  Print media specifications on  page 
110.)
• Fla
tten any curl on postcards, envelopes, and labels before loading 
th
 em into the multi-purpose tray.
1. Hold  the handle of multi-purpose tray and pull it down to open and 
pull
  out the multi-purpos e tray paper extension .
3
2.Flex or fan the edge of the paper  stack to separate the pages before 
loading paper.
3. Place paper with the side you want to print facing up.
 •When printing the special media, you must follow the load -
ing guideline. (See  Printing on special media on page  47 .)
• Wh
en papers overlap when printing using Multi-purpose 
tra
 y, open tray 1 and remove overlapping papers then try 
printing again. 
• When paper does not feed well while printing, push the 
pap
 er in manually until it starts feeding automatically. 
Downloaded From ManualsPrinter.com Manuals 
						

							Media and tray_ 47
4.Squeeze the multi-purpose tray pa per width guides and adjust them 
to the width of the paper. Do not  force them too much, or the paper 
will bent resulting in a paper jam or skew.
5. When you print a document, set the paper type and size for the 
multi-purpose tray. For informati on about setting the paper type and 
size on the control panel (see  Setting the default tray and paper on 
page  49).
PRINTING ON SPECIAL MEDIA
The table below shows the available special media for each tray. 
The paper setting in the machine and driver should match to print without a 
paper  mismatch error. 
T

o change the paper setting se t in the machine, 
 from the Samsung Easy 
Printer Manager  select 
(Switch to advanced mode)  > Device Set -
tings .
Or if your machine supports a display screen, you can set it using the 
(Menu ) button on the control panel.
Then, set the paper type from the  Printing pre
 ferences window >  Paper 
tab >  Paper Type  (see Opening printing preferences on page  52 ).
 When using special media, we recommend you feed one paper at a 
time. Check the maximum input number of media for each tray (See 
Print media specifications on page  110 ).
TypesTray 1Optional trayMulti-purpose 
tray
Plain ●● ●
Thick  ●● ●
Thicker   ●
Thin   ●● ●
Bond ●● ●
Color ●● ●
CardStock ●● ●
Labels ●● ●
Transparency ● ●
Envelope●●
 (onl y for 
op tional tray 2) ●
Preprinted ●● ●
Cotton  ●● ●
Recycled ●● ●
Archive ●● ●
Hole Punched ●●
●
(●: Supported, Blank:  Not supported) 
 When you use recycled paper as a used paper, printouts might be 
wrinkled and/or jamming may occur due to excessive curl.
Envelope
Successful printing on envelopes depends upon the quality of the enve -
lopes. 
To print an envelope, place it flap si d
e
  up with the stamp area bottom the 
top right side.
• When selecting envelopes, consider the following factors:
-Wei ght:  Th
 e weight of the envelope paper should not exceed 
90  g/m2 otherwise, jam may occur.
- Construction:  Pri
 or to printing, envelopes should lie flat with less 
than a 7  mm 
curl and should not contain air.
- Co
ndition:  Env
 elopes should not be wrinkled, nicked, either dam -
aged.
- Temperature:  Use enve
 lopes that are compatible with th e heat and 
pressure of the machine during operation.
• U
se only well-constructed envelopes with sharp-and well-creased folds.
• Do not use stamped envelopes.
• Do not use envelopes with clasps, snaps, windows, coated lining, 
self-
 adhesive seals, or  other synthetic materials.
• D
o not use damaged or poorly made envelopes.
• Be sure the seam at both ends of the envelope extends all the way to 
the
  corner of the envelope.
21
1 Acceptable
2 Unacceptable
• Envelopes with a peel-off adhesive strip or with more than one flap that 
folds over to seal must use adhes ives compatible with the machine’s 
TypesTray 1Optional trayMulti-purpose 
tray
Downloaded From ManualsPrinter.com Manuals 
						

							Media and tray_ 48
fusing temperature about 170°C (338 °F) for 0.1 second. The extra flaps 
and strips might cause wrinkling, creasing, or jams and may even dam -
age the fuser.
• For the best print qual ity, posi
 tion margins no closer than 15 mm from 
the edge
s of the envelope.
• Avo
id printing over the area where the envelope’s seams meet.
Transparency
To avoid damaging the machine, use on ly transparencies designed for use 
in laser printers.
• Transparencies used in the mach ine must be able to withstand 
machine’s fusing temperature.
• Place them on a flat 
 surface after removing them from the machine.
• Do n ot leave unused transparencies in the paper tray for long periods of 
ti
 me. Dust and dirt may accumulate on  them, resulting in spotty printing.
• To avo
id smudging caused by fingerprints, handle them carefully.
• To a void fading, do not expose printed transparencies to prolonged sun -
ligh
 t.
• Ensure 
that transp
 arencies are not wrinkled, curled, or have any torn 
edges.
• Do not use tran
 sparencies that separates from the backing sheet.
• To prevent transparencies from sticking to each other, do not let the 
p
 rinted sheets stack up as they are begin printed out. 
• Base 
type transparency (ex. Xerox 3R3117) results in better image and 
pap
 er handling quality than paper backed (ex. Xerox 3R3028) or remov -
able stripe (3R3108) ones.
 
Depending on the selection or st orage conditions of the transpar-
ency, jam or image scratch might occur.
Labels
To avoid damaging the machine, use on ly labels designed for use in laser 
machines.
• When selecting labels, consider the following factors:
-Adhesives:  Th
 e adhesive material should be stable at your 
machine’s fu
sing temperature about 170°C (338 °F). -
Arra
ngement:  Onl
 y use labels with no exposed backing between 
them. La
bels can peel off sheets that have spaces between the 
labels, causing serious jams.
- Cur l: Prior to 
 printing, labels must lie flat with no more than 13  mm 
of curl in any direction.
- Co
ndition:  D
 o not use labels with wrinkl es, bubbl es, or other indica-
tions of separation.
• Do not use labels with slick back.
• Do not use partially used labels. 
• Do not use the labels with separated edges.
• Make  sure that there is no exposed adhesive material between labels. 
Exp
 osed areas can cause labels to peel off during printing, which can 
cause paper jams. Exposed adhesive can also cause damage to 
machine components.
• D
o not run a sheet of labels through the machine more than once. The 
a
 dhesive backing is designed for only a single pass through the 
machine.
• D
o not use labels that are separating from the backing sheet or are wrin-
kl
 ed, bubbled, or otherwise damaged.
Card stock/Cust om-sized paper
•Do not print on media smaller than 76.2  mm (3 inches) wide or 127  mm 
(5 inches) long.
• In the software appl
 ication, set margins at least 6.4  mm (0.25 inches) 
aw
ay from the edges of the material.
• U
sable minimum weight of 3*5 inches paper is 105g/m². (28 lbs bond)
• Ensure that 76.2  mm 
 (3 inches) X 127 mm (5 inches) is not curled or has 
no
 torn edges. Depending on the curl of 76.2  mm (3 inches) X 127  mm 
(5  

inches) paper, jam might occur.
Downloaded From ManualsPrinter.com Manuals 
						

							Media and tray_ 49
Letterhead/Preprinted paper
Single-sideddouble-sided
Tray1
Optional tray Face 
dow
nFace 
up
Multi-pur -
pose tray Face 
upFace 
down
•
Letterhead/ Preprinted paper must be pr inted with heat-resistant ink that 
will not melt, vaporize, or release hazardous emissions when subjected 
to the machine’s fusing temperature for 0.1 second. Check your 
machine’s specification to view t he fusing temperature about 170°C (338 
°F).
• Letterhea
d/ Prep
 rinted paper ink must be non-flammable and should not 
adversely affect machine rollers.
• Forms and 
 letterhead should be sealed in a moisture-proof wrapping to 
prevent changes during storage.
• Before you loa
d
  letterhead/preprinted paper, verify that the ink on the 
paper is dry. During the fusing process, wet ink can come off preprinted 
paper, reducing print quality.
Used paper
When loading used paper, printed side should be facing down with an 
uncurled edge at the front. If you expe rience problems with paper feed, turn 
the paper around. Note that print quality is not guaranteed.
• Used paper must be printed with heat-re sistant ink that will not melt, 
vaporize, or release hazardous  emissions when subjected to the 
machine’s fusing temperature for 0.1 second. Check your machine’s 
specification to view the fusing  temperature about 170°C(338 °F). 
• Used pa
per ink mu
 st be non-flammable and should not adversely affect  machine rollers.
• Be
fore you load used paper, verify that the ink on the paper is dry. Dur -
i
 ng the fusing process, wet ink can  come off used  paper, reducing print 
quality.
SETTING THE DEFAULT TRAY AND PAPER
The paper setting in the machine and dr iver should match to print without a 
paper mismatch error. 
To change the paper setting set in the machine, from the  Samsun
 g Easy 
Printer Manager  select 
(Switch to advanced mode)  > Device Set -
tings .
Or if your machine supports a displa y screen, you
  can set it using the 
(Menu) button on the control panel.
Then, set the paper type from the  Printing p
 references window > Paper 
tab >  Paper Type  (see Opening printing preferences on page  52 ).
In the control panel
Setting the paper size
1. Press  Menu on the control panel.
2. Press the up/down arrow to highlight  Paper an
 d press OK.
3. Press the up/down arrow to select the tray you want and press  OK.
4. Press the up/down arrow to highlight  Paper Siz
 e and press  OK.
5. Press the up/down arrow to select  the p
 aper size you want and press 
OK .
6. Pr
ess  Stop/Clear
  to return to the ready mode.
Setting the paper type
1.Press  Menu on the control panel.
2. Press the up/down arrow to highlight  Paper an
 d press OK.
3. Press the up/down arrow to select the tray you want and press  OK.
4. Press the up/down arrow to highlight  Pa
 per Type and press  OK.
5. Press the up/down arrow to select the paper tray you want and press 
OK .
6. Pr
ess  Stop/Clear
  to return to the ready mode.
Setting the paper source
1.Press  Menu on the control panel.
2. Press the up/down arrow to highlight  Paper an
 d press OK.
3. Press the up/down arrow to select the paper source you want and 
press  OK.
4. Press  Stop/Clear
  to return to ready mode.
In the computer
Windows
1.Click the Windows Start  menu. 
2. For Wi ndows 2000, select  S
 ettings > Printers .
• For Windows XP/2003, select  Prin
 ters and Faxes. 
• For Windows 2008/Vista, select Control Panel  > 
 Hardware and 
Sound >  Printers. 
• For Windows 7, select  Contr
o
 l Panel > Hardware and Sound  > 
Devices and Printers . 
• For Windows Server 2008 R2, select  Control Pane
 l > Hardware 
>  Devices and Printers . 
Downloaded From ManualsPrinter.com Manuals 
						

							Media and tray_ 50
3.Right-click your machine.
4. Fo
r Windows XP/2003/2008/Vista, press  Printing Preferences.
For Windows 7 and Windows Server 2008 R2, from context menus, 
select the  Printing

 Preferences.
 If Printing Preferences  item has ► mark, you can select other 
printer drivers connect ed with selected printer.
5. Cli
ck  Paper tab. 
6. Sele
ct tray and its options, such as paper size and type.
7.Press  OK.
 If you want to use special-sized paper such as a billing paper, 
select  Paper tab > Size > Edit...  in the  Printing Preferences  (See 
Opening printing preferences on page  52 ).
Mac
Mac does not support this functi on. Mac users need to change the 
default setting manually each time t hey want to print using other set-
tings. 
1. Op
en a Mac application and select the file you want to print.
2.Op
en the  File menu and click  Print.
3. Go
 to  Paper Feed  pane.
4. Set 
appropriate tray from which you want to print.
5.Go
 to  Paper pane.
6. Set p
aper type to correspond to t he paper loaded in the tray from 
which you want to print.
7. Cli
ck  Print to print. 
Linux
1.Open  Terminal Program
2. Wh
en the Terminal screen appears, type in the following: 
[root@localhost root]# lpr [FileName]
3. Select  Printer  and 
 click Properties…
4. Cli
ck  Advanced  tab.
5. Sele
ct tray (source) and its options, such as paper size and type.
6.Press  OK.
Downloaded From ManualsPrinter.com Manuals