Samsung ML 6510ND User Manual

							OSCONTENTS
Windows •Printer driver:  Use th
 is driver to take full advantage of 
your
 machine’s features.
• PostScript Printer Driver:  Use the PostScrip
 t driver 
to print documents with comple x fonts and graphics in 
the PS language. (PostScript printer description file is 
included.)
• Smart Panel:  This program allows you to monitor the 
machi ne’s sta

tus and alerts you when an error occurs 
during printing.
• Prin
ter Settings Utility:  T
 his program allows you to 
set up printer’
s other options  from your computer desk -
top.
• Direct Print i
 ng Utility: This program allows you to 
print 
PDF files directly.
• SetIP:  Use this program to set your machine’s TCP/IP 
ad dresses.
• XPS printer driver:  Use to pri

nt documents in XPS 
print path. XPS pr

inter driver  can be installed only on 
Windows Vista or higher.
Mac •Prin
ter driver:  Use thi
 s driver to run your machine 
from a Mac computer and pr int documents. (PostScript 
prin
ter description file is included.)
• Smart Panel:  This program allows you to monitor the 
machine’s status.
• Prin
ter Settings Utility:  T
 his program allows you to 
set up printer’
s other options  from your computer desk -
top.
• SetIP:  Use this program to set your machine’s TCP/IP 
ad dresses.
Li

nux •Unified Linux Driver:  Use 
 this driver to take full 
advantage
 of your machine’s features.
• PostScript Printer 
Driver: Use thi
 s driver to run your 
machine fro
m a Linux computer and print documents. 
(PostScript printer description file is included.)
• Smart Panel:  This program allows you to monitor the 
machine’s status.
• Prin
ter Settings Utility:  T
 his program allows you to 
set up printer’
s other options  from your computer desk -
top.
• SetIP:  Use this program to set your machine’s TCP/IP 
ad dresses.
Unix •UNI X Printer driver:   Use th
 is driver to take full 
advantage
 of your machines feature.
Getting started _ 31
SYSTEM REQUIREMENTS
Before you begin, ensure  that your system meets the following require-
ments:
Microsoft® Windows®
Your machine supports the following Windows operating systems.
OPERATING  SYSTEMREQUIREMENT (RECOMMENDED)
CPURAMFREE HDD 
SPACE
Windows 2000
®Intel® Pentium® II 400 
MHz (Pentium III 933 
MHz) 64 MB 

(128 MB) 600 MB
Windows XP
®Intel® Pentium® III 933 
MHz (Pentium IV 1 GHz) 128 MB 

(256 MB) 1.5 GB
Windows 
Se rve

r® 2003 Intel
® Pentium® III 933 
MHz (Pentium IV 1 GHz) 128 MB 

(512 MB) 1.25 GB to 

2 GB
Windows 
Se rve

r® 2008 Intel
® Pentium® IV 1 GHz 
(Pentium IV 2 GHz) 512 MB 

(2048 MB) 10 GB
Windows Vista
®Intel® Pentium® IV 3 GHz 512 MB 

(1024 MB) 15 GB
Windows
® 7 Intel® Pentium® IV 1 GHz 
32-bit or 64-bit processor 
or higher 1 GB (2 
GB)
16 GB
• Su
pport for DirectX
® 9 graphics with 128 MB memory 
(to enable the Aero theme).
• DV
D-R/W Drive
Wi

ndows 
Serve
 r® 2008 R2 Intel
® Pentium® IV 1 GHz 
(x86) or 1.4 GHz (x64) 
processors (2 GHz or 
faster) 512 MB 

(2048 MB) 10 GB
 •
Internet Explorer® 6.0 or higher is the mi nimum requirement for all 
Windows operating systems.
• Adm
inistrator rights are required to install the software.
• Windows Terminal Services  
 is compatible with this machine.
• For Windows 2000, Services Pack 4 or higher is required. 
Mac
OPERAT -
ING SYS -
TEM
REQUIREMENTS (RECOMMENDED)
CPURAMFREE HDD 
SPACE
Mac OS X 
10.3 ~ 10.4 •
Intel
® Proces-
sors
• PowerPC G4/ 
G5 •
128 MB for a 
PowerPC ba sed 
Mac (512 MB)
• 512  MB for a 
In
 tel-based Mac 
(1 GB) 1 GB
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 32
Linux
ITEMREQUIREMENT (RECOMMENDED)
Operating sys -
tem RedHat
® Enterprise Linux WS 4, 5 (32/64 bit)
Fedora 4, 5, 6, 7, 8,  9
 , 10, 11, 12 (32/64bit)
SuSE Linux 10.0, 10.1 (32bit)
OpenSuSE 10.2, 10.3, 11.0,  11.1, 1
 1.2 (32/64bit)
Mandriva 2005, 2006, 2007, 2008, 2009, 2009.1 
(3 2/

64bit)
Ubuntu 5.04, 5.10,  6.06, 6.10

, 7.04, 7.10, 8.04, 8.10, 
9.04, 9.10 (32/64bit)
SuSE Linux Enterprise Desktop 10, 11 (32/64bit)
Debian 4.0, 5.0 (32/64bit)
CPU Pentium
® IV 2.4 GHz (Intel Core™2)
RAM 512 MB (1024 MB)
Free HDD space 1 GB (2 GB)
UNIX
ITEMREQUIREMENTS
Operating sys -
tem Sun Solaris 9,10 (x86, SPARC) 
IBM AIX 5.1, 5.2, 5.3, 5.4
HP-UX 11i v1, 11i v2, 11i v3 (PA-RISC, Itanium)
Free HDD space Up to 100 MB
INSTALLING LOCAL LY CONNECTED 
MACHINE’S DRIVER
 Only use an USB cable no longer then 3 m (10 ft.).
Windows
You can install the machine software  using the typical or custom method.
The following steps below are recommended for most users who use a 
machi ne directly co

nnected to your computer. All components necessary for 
machine operations will be installed.
1. Make  sure that the machine is connected locally and powered on.
2. Inse rt the supplied software CD into your CD-ROM drive.
If the installation window does not appear, click  Start > All programs > 
Accessories  > Run.
X:\ Setup.exe  repl
acing
  “X” with the letter, which represents your 
CD-ROM drive and click  OK.
3. Review and accept the installation agreements in the installation win -
do
 w. Then, click Nex t.
4. Select  USB co
 nnection on the Printer Connection Type screen. 
Then, click  Next.
5. F
ollow the instructions in the installation window.
 You can select the software applications in the  Select Software to 
Install  Window.
 If the printer driver does not work properly, follow the steps below to 
uninstall and reinstall the driver.
a)Make sure that the machine is connected to your computer and 
p

owered on.
b) From the  Start menu, select  Programs
  or All Programs  > Sam-
sung Printers  > Uninstall Sams
 ung Printer Software .
c) Select the necessary option and follow the instructions in the win -
do
 w.
d) After u
ninstalling the printer driver, reinstall it (see  
 Installing 
locally connected machine’s driver on page  32 , Installing network 
connected machine’s driver on page  38 ).
Silent installation Mode (Windows only)
Silent installation mode is an insta llation method that does not require 
any user intervention. On ce you start the installation, the machine driver 
and software are automatically inst alled on you computer. You can start 
the silent installation by typing  /s or  /S in the command window.
Command-line Parameters
Following table shows commands that can be used in the command win -
dow.
 Following command-line are effective and operated when com -
mand is used with  /s or /S . But /h , /H  or  /? are exceptional com-
mands that can be operated solely.
Mac OS X 
10.5
•
Intel
® Proces -
sors
• 86
7 MHz or 
faster Power 
PC G4

/ G5512 MB (1 GB)
1 GB
Mac OS X 
10.6 ~10.8 •
Intel
® Proces -
sors 1 GB (2 GB)
1 GB
OPERAT-
ING SYS- TEMREQUIREMENTS (RECOMMENDED)
CPURAMFREE HDD SPACE
Downloaded From ManualsPrinter.com Manuals 
						

							COMMAND- LINEDEFINITIONDESCRIPTION
/s or
/S Starts silent installation. Installs machine drivers 
without prompting any 
UIs or user intervention.
/p”” 
or
/P””Specifies printer port.
 Network Port will 
be created by use 
of Standard 
TCP/IP Port moni
-
tor. For local port, 
this port  must 
exist on system 
be

fore being spec -
ified by command. Printer port name can be 
spe
c

ified as IP address, 
hostname, USB local port 
name, IEEE1284 port 
name or network path.
For example:
•  /p”x
xx.xxx.xxx.xxx” in 
w
 here, 
“xxx.xxx.xxx.xxx” 
means IP address for 
network printer. 
/p”USB001”, 
/P”LPT1:”, /p”host -
name”
• /p\\comput
e
 r_name\sha
red_printer or 
\\xxx.xxx.xxx.xxx\sha
red_printer in where,  
\\computer_name\sh
ared_printer or 
\\xxx.xxx.xxx.xxx\sha
red_printer means 
the network path to 
the printer by enter -
ing two slashes, the 
computer name or 
local IP address of the 
PC sharing the 
printer, and then the 
share name of the 
printer.
/a”” 
or
/A”” Specifies destination 
path for installa
tion.
 The destination 
path should be a 
fully qualified path.
Since machine drivers 
should be installed on the 
OS specific location, this 
command applies to only 
application software.
/n”” or
/N”” Speci

fies printer name. 
Printer in sta

nce shall be 
created as specified 
printer name.With this pa rameter, you 
can add printer instances 
as your wishes.
/nd or
/ND Commands not to set 
the installed drive
r as a 
default machine driver. It indicates installed 
machi
ne drive
r will not be 
the default machine 
driver on your system if 
there are one or more 
printer drivers installed. If 
there is no installed 
machine driver on your 
system, then this option 
won’t be applied because 
Windows OS will set 
installed printer driver as 
a default machine driver. /x or
/X
Uses existing machine 
driver files to 
cre

ate 
printer instance if it is 
already installed.This command provides a 
way to install a printer 
instance that uses 
installed printer driver 
files without installing an 
additional driver.
/up”” or
/UP” ” Removes onl

y specified 
printer instan ce

 and not 
the driver files. This command provides a 
way to re
move only spec -
ified printer instance from 
your system without 
effecting other printer 
drivers. It will not remove 
printer driver files from 
your system.
/d or
/D Uninstalls all device 
drivers and a
pplications 
from your system. This command will 
remove all 
installed 
device drivers and appli -
cation software from your 
system.
/v”” 
or
/V”” Shares instal

led 
machin e a

nd add other 
available platform driv -
ers for Point & Print. It will install all supported 
Window
s OS platform’s 
machine drivers to sys -
tem and share it with 
specified  
for point and print.
/o or 
/OOpens 
Printers and 
Faxes  fo
lder after instal -
lation.This command will open 
Printers and Faxes  
folder after the silent 
installation.
/h, /H or /? Shows Command-line Usage.
Getting started_ 33
Mac
1.Make sure that the machine is connected to your computer and powered 
on.
2. Inse
rt the supplied software CD into your CD-ROM drive.
3. Double-click the CD-ROM icon that appears on your Mac desktop.
4. Double-click the  M
 AC_Installer folder.
5. Double-click the  In
 staller OS X icon.
6. Enter the password and click  OK.
7. The Samsung Installer window opens. Click  Continue.
8. Read the license agreement and click  Co
 ntinue.
9. Click  Agree
  to agree to the license agreement.
10. Select  Easy In
 stall and click  Install. Easy Install is recommended for 
most users. All components necessa ry for machine operations will be 
installed. 
If you select  Cu
 stom Install, you can choose individual components to 
install.
11. When
 the message which warns that all applications will close on your 
co
 mputer appears, click  Continue.
12. Select  Typi
cal 
 installation for a local printer  and then click OK.
 If you select Typical installation for a network printer  during the 
machine driver installation, the  SetIP program automatically runs. 
If the machine has already configured network information, close 
COMMAND-  LINEDEFINITIONDESCRIPTION
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 34
the SetIP program. Go to the next step.
13. After th e installation is finished, click  Qu
 it.
14. Ope n the Applications  folder > Uti
 lities > Print Setup Utility .
• For Mac OS X 10.5~10.8, open the  Applic
 ations folder >  System 
Preferences  and click Print and Fax .
15. Click  Add on th
e Printer List .
• For Mac OS X 10.5~10.8, click the “ +” icon; a di
 splay window will pop 
up. 
16. For Mac OS X 1
 0.3, select the USB tab. 
• For M ac OS X10.4, click  Default Browser
  and find the USB connec-
tion.
• For 
Mac OS X 10.5~10.8, click  De
 fault and find the USB connection.
17. For Mac OS X  1
 0.3, if Auto Select does not work properly, select  Sam-
sung  in Printer Model  
 and your machine name in  Model Name.
• For Mac OS X 10.4, if Auto Select does not work properly, select 
Samsung  in Prin

t Using and your machine name in  Model. 
• For Mac OS X 10.5~10.8, if Auto Select does not work properly, 
select  Select a d

river to use... and your machine name in  Print 
Using . 
Your machine appears on the  Printer List, 
a
 nd is set as the default 
machine.
18. Click  Add.
 If the printer driver does not work properly, uninstall the driver and 
reinstall it. 
Follow steps below to uninstall the driver for Mac.
a)Make sure that the machine is connected to your computer and 
powe
 red on.
b) In
sert the supplied software CD into your CD-ROM drive.
c) Doub le-click CD-ROM icon that appears on your Mac desktop.
d) Doub le-click the  MA
 C_Installer folder.
e) Doub le-click the  In
 staller OS X icon.
f) Ente r the password and click  OK.
g) The  Samsung Installer window opens. Click  Cont
 inue.
h) Select  Uninst
 all and click  Uninstall. 
i) Whe n the message which warns that all applications will close on 
your computer appe
 ars, Click Continue.
j) When the uninstall is done, click  Qu
 it.
Linux
You need to download the Linux software package from the Samsung web -
site to install the printer software. 
Follow the steps below to install the software.
Installing the Linux Unified Driver
1. Make sure that the machine is co nnected to your computer and pow -
ered on.
2. W
hen the  A
 dministrator Login  window appears, type in root in the 
Login  field and enter the system password.
 You must log in as a super user (root) to install the machine 
software. If you are not a super  user, ask your system adminis-
trator.
3. From th e Samsung website, download the Unified Linux Driver pack -
age
  to your computer.
4. Righ
t click the Uni
 fied Linux Driver package and extract the pack -
age. 
5. Doub
le click  cd
 root > autorun .
6. Whe n the welcome screen appears, click Next .
7.When the installation is complete, click  Finish.
The installation program has added  the Unif
 ied Driver Configurator 
desktop icon and the Unified Driver  group to the system menu for your 
convenience. If you have any difficulties, consult the on screen help that 
is available through your system me nu or can otherwise be called from 
the driver package Windows applications, such as  Unified Driver Con-
figurator  or I
m
 age Manager.
Installing the SmartPanel
1.Make sure that the machine is co nnected to your computer and pow -
ered on.
2. W
hen the  A
 dministrator Login  window appears, type in root in the 
Login  field and enter the system password.
 You must log in as a super user (root) to install the machine 
software. If you are not a super  user, ask your system adminis-
trator.
3. From th e Samsung web
 site, download the Smart Panel package to 
your computer.
4. Right click the Smart Panel package and extract the package. 
5. Doub le click  cd
 root > Linux  > smartpanel  > install.sh.
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 35
Installing the Printer Settings Utility
1.Make sure that the machine is connected to your computer and pow -
ered on.
2. Wh
en the Administrator Login  window appears, type in root in the 
Login  field and enter t he system password.
 You must log in as a super user  (root) to install the machine 
software. If you are not a super user, ask your system adminis -
trator.
3. Fro
m the Samsung website, down load the Printer Setting Utility 
package to your computer.
4. Rig
ht click the  Printer Settings Utility  package and extract the 
package. 
5. Dou
ble click  cdroot > Linux  > psu > install.sh .
 If the printer driver does not work properly, uninstall the driver and 
reinstall it again. 
Follow the steps below to uninstall the driver for Linux.
a)Make sure
  that the machine is connected to your computer and 
powered on.
b) Wh
en the Administrator Login  window appears, type in “root” 
in the  Login field and enter t he system password.
You must log in as a super user  (root) 
 to uninstall the printer 
driver. If you are not a super user, ask your system administra -
tor.
c) C
lick the icon at the bottom of  the desktop. When the Terminal 
screen appears, type in:
[root@localhost root]#cd  /opt/Samsung/mfp/u
 ninstall/
[root@localhost uninst a
 ll]#./uninstall.sh
d) Cli
ck  Uninstall .
e) Cli
ck  Next. 
f) Cli
ck  Finish.
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 36
3.network setup
This chapter gives you step-by-step  instructions for setting up the network connected machine and software.
This chapter includes:
•Network environment
• Introducing useful network programs
• Using a wired network •
Installing network connected machine’s driver
• IPv6 Configuration
  
 Supported optional devices and features may differ according to your 
model. Please check your model name (See  Features by Models on 
page  25).
NETWORK ENVIRONMENT
You need to set up the network protocols on the machine to use it as your 
network machine. You can set up the basic network settings through the 
machines control panel.
The following table shows the networ k environmen
 ts supported by the 
machine:
ITEMSPECIFICATIONS
Network interface •Ethernet 10/100/1000 Base-TX
• 802.11  b/g/n Wireless LAN (Optional)
N

etwork operating system •Windows 
2000

/XP/2003/2008/Vista/7/2008 
Server R2
• Variou s Linux OS
• Mac OS X 10.3 ~ 10.8
• UNIX
• Novell
 NetWare 5.x, 6.x (TCP/IP Only)
Ne

twork protocols •TCP/IPv4
• 802.1x
• DHCP, BOOTP, 
AutoIP
• DNS, WINS, Bo njo
 ur, SLP, UPnP
• Stan dard TCP/IP Printing (RAW), LPR, 
IPP, WSD
• SNMPv 1/2/3, HTT
P
  (S), Telnet, SMTP 
(S), LDAP (S), IPSec
• SMB, FTP, Kerberos
• TCP/IPv6  (DHC
 P, DNS, RAW, LPR, 
SNMPv 1/2/3, HTTP (S), IPSec)
(See  IPv6 Configuration on page  40.)
Wireless security 
(Op t

ional) •
Authentication: Open  System,  Shared 
Key, WPA Personal,  WPA2 Personal 
(PSK)
• Encryp tion: WEP64, WEP128, TKIP, 
AE
 S
INTRODUCING USEFUL  NETWORK PROGRAMS
There are several programs available to setup the network settings easily in 
network environment. For the network administrator especially, managing 
several machines on the network is possible.
 Before using the programs below, set the IP address first.
SyncThru™ Web Service
Web server embedded on your network machine, which allows you to:
•Configure the network parameters necessary for the machine to connect 
to vario
 us network environments.
• Customize m
 achine settings.
(See  Using SyncThru™ Web Service on page  68 .)
SyncThru™ Web Admin Service
A web-based machine management solution for network administrators. 
SyncThru™ Web Admin Service provides you with an efficient way of man -
aging network devices and lets you remotely monitor and troubleshoot net -
work machines from any site with corporate internet access. Download this 
program from http://solution.samsungprinter.com.
SetIP
This utility program allows you to se lect a network interface and manually 
configure the IP addresses for us e with the TCP/IP protocol (See IPv4 set-
ting using SetIP Program (Windows) on page  37 , IPv4 setting using SetIP 
Program (Mac) on page  37 or  IPv4 setting using SetIP Program (Linux) 
on page  38 ).
 TCP/IPv6 is not supported by this program.
USING A WIRED NETWORK
You must set up the network protocol s on your machine to use it on your 
network. This chapter will show you how this is easily accomplished.
You can use network after connecting network cable to a corresponding 
po rt 

on your machine. 
Printing configuration report
You can print a  Configuration Report  from the machine’s control panel that 
will show the current machine’s network se ttings. This will help you to set up 
a network and troubleshoot problems.
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 37
1.Press  Menu on the control panel.
2. Press the up/down arrow to highlight  Information and
  press OK.
3. Press the up/down arrow to highlight  Con
 figuration and press OK .
The machine prints the  Config
 uration Report.
Using this  Conf
 iguration Report , you can find your machine MAC address 
and IP address.
For example:
• MAC  Address: 00:15:99:41:A2:78
• IP Addre s
 s: 192.0.0.192
Setting IPv4 address
You must set up an IPv4 address for network printing and management. In 
most cases a new IP address will be automatically assigned by a DHCP 
(Dynamic Host Configuration Protoc ol) server located on the network.
 If you use IPv6 address, refer to IPv6 Configuration on page 40
In a few situations the IP address must be set manually. This is called a 
static IP and  

is often required in co rporate Intranets for security reasons.
• DHCP IP a ssignment : Co
 nnect your machine to the network, and wait a 
few minutes for the DHCP server to assign an IP address to the 
machine. Then, print the  Configuration Report as explained above. If 
the report shows that the IP addr ess has changed, the assignment was 
successful. You will see the new IP address in the report.
• Static IP assignment : Use th
 e SetIP program to change the IP address 
from your computer. If your machine has a control panel, you can also 
change the IP address using the machines control panel.
In an office environment, we recommend that you contact a network admin -
istrator to set this address for you.
IPv4 setting using control panel
1. Connect your machine to the network with a network cable.
2. Turn on the machine.
3. Press  Menu on
  the control panel.
4. Press the  u
 p/down arrow to highlight  Network and press  OK.
5. Press the  u
 p/down arrow to highlight  TCP/IP (IPv4) and press OK.
6. Press the  u
 p/down arrow to highlight  Set IPv4 Address and press 
OK .
7. Press the
 u
 p/down arrow to highlight  Manual and press  OK.
8. Enter the  
 IP address using numeric keypad and press  OK.
9. In th e same way, enter other parameters such as  Subnet Mask and
  -
Gateway  and  press OK.
10. After enterin g 
 all parameters, press  Stop/Clear to return to the ready 
mode.
Now go to Installing network connected machine’s driver on page  38.
IPv4 setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your 
machine using its MAC address to communicate with the machine. A 
MAC address is the hardware serial number of the network interface and 
can be found in the  Configuration Report .
For using SetIP program, disable the  co
mputer firewa
 ll before continuing 
by performing the following:
1. Open 
Control Panel .
2. Dou ble click  Secu
 rity Center.
3. Click  W
indows Firewall .
4. Disab le the firewall.
Installing the program
1.Insert the Printer Software CD-R OM provided with your machine. 
When the driver CD runs autom atically, close that window.
2. Sta
rt a web browser such as Internet Explorer and open the X drive. 
(X 
 represents your CD-ROM drive.)
3. Doub
le-click  Applic
 ation > SetIP .
4. Doub le-click  Setu
 p.exe to install this program.
5. Click  OK. If necessa ry, se
 lect a language from the drop-down list.
6. Follow the instructions in the wi ndow
  and complete the installation.
Starting the program
1.Connect your machine and the computer using network cable.
2. Turn on the machine.
3. From th e Win
 dows Start menu, select  All Programs > Samsung 
Printers  > SetIP  > SetIP.
4. Click on the 
 icon (third from left) in the SetIP window to open the 
TCP/IP configuration window.
5. Enter the machine’s new information into the configuration window 
as fol
 lows:
•MAC Address : Find the machine’s MAC address on the  Config-
uration Report  a nd enter it without the colons. For example, 
00:15:99:29:51:A8 bec omes 0015992951A8.
 A MAC address is a hardware serial number of the machine’s 
network interface and can be found in the  Configuration 
Report .
• IP Address : Enter 
 a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150, 
enter 192 .1

68.1.X. (X is num ber between 1 and 254 other than 
the computer’s address.)
• Subnet Mask : Enter a new Sub
 net Mask for your machine.
• Default Gateway : Ente
 r a new Gateway for your machine.
6. Click  Apply , and then click  OK. The 
 machine will automatically print 
the  Configuration Report . Confirm that all of the settings are cor -
rect.
7. Click  Exit to close the SetIP prog
ram.
8. If necessary,  re
 start the computer’s firewall.
IPv4 setting using SetIP Program (Mac)
For using SetIP program, disable the computer firewall before continuing 
by performing the following:
 The path and UIs may differ by Ma c OS version. Refer to the Mac 
OS manual to turn firewall off.
1. Open  System
  Preferences.
2. Click  Security.
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 38
3.Click the  Firewall menu.
4. Turn the firewall off.
 The following instructions may vary for your model.
Perform the following to configure the IP address:
1. Con nect your machine and the computer using network cable.
2. Insert  the Installation CD-ROM, and open the disk window. Open the 
MAC_Ins
 taller > MAC_Printer  > SetIP  > SetIPApplet.html .
3. Double click the file and  Saf
 ari will automatically open, then select 
Trust . The browser will open the  SetIPApplet.html page that shows 
the printer’s name and IP address information. 
4. Click on the 
 icon (third from left) in the SetIP window to open the 
TCP/IP configuration window.
5. Enter the 
 printer’s new information into the configuration window as 
follows. In a corporate intranet, you may need to have this informa -
tion assigned by a network  manager before proce
 eding.
• MAC Addre s
 s: Find the machine’s MAC address from the  Con-
figuration Report  and 
 enter it without the colons. For example, 
00:15:99:29:51:A8 becomes 0015992951A8.
 The MAC address is the hardware serial number of the 
on-board network interface and can be found on the  Con-
figuration Report .
• IP Addre s
 s: Enter a new IP address for your printer.
For example, if your computer’s  IP addre
 ss is 192.168.1.150, 
enter 192.168.1.X. (X is number between 1 and 254 other than 
the computer’s address.)
• Subnet Mask : 
 Enter a new Subnet Mask for your machine.
• Def ault Gateway : Ent
 er a new Gateway for your machine.
6. Select  Apply, then OK, and  OK  
 again. The printer will automatically 
print the configuration r eport. Confirm that all of the settings are cor -
rect. Qu it Safari . You
  may close and eject the installation CD-ROM. 
If necessary, restart the computer’s  firewall. You have successfully 
changed the IP address, subnet mask, and gateway.
IPv4 setting using SetIP Program (Linux)
The SetIP program should be automatically installed during the printer 
driver installation.
 The path and UIs may differ by Linux OS version. Refer to the 
Linux OS manual to turn firewall off.
1. Print the 
 machine’s configuration report to find your machine’s MAC 
address. 
2. Open the / opt/Samsung /mfp /sh
 are/utils /.
3. Dou ble click the  SetIP
 Applet.html file. 
4. Click to open the TCP/IP configuration window. 
5. Enter the  
 MAC address, IP address,  subnet mask, default gateway, 
and then click  Apply. 
 When you enter the MAC address,  enter it without a colon(:).
6. The machine prints the network information. Confirm all of the set -
tings are correct. 
7. C
lose the SetIP program. 
Network parameter setting
You can also set up the various network settings through the network 
administration programs such as SyncThru™ Web Admin Service and 
SyncThru™ Web Service.
Restoring factory default settings using SyncThru™ 
Web Service
1. Start a web browser such as Internet Explorer, Safari or Firefox and 
enter your machine’s new IP address in the browser window.
2. Click  Go 
to access th
 e SyncThru™ Web Service.
3. Click  Logi
 n on the upper right of the SyncThru™ Web Service web -
site.
A log-in page appears. 
4. Type
 in the  ID and
  Password  then click Login.
If it’s your first time logging into  SyncTh
 ru™ Web Service, type in the 
below default ID and password.
• ID:  admin  
• Pass word:  s
 ec00000 
5. When the  Syn
 cThru™ Web Service  window opens, click Settings 
>  Network Settings  > Restore Default .
6. Click  Clear  for 
network.
7. Turn  off and restart machine to apply settings.
INSTALLING NETW ORK CONNECTED 
MACHINE’S DRIVER
Windows
This is recommended for most users. All components necessary for 
machine operations will be installed.
Follow the steps below:
1.Make  sure that the machine is connected to the network and powered 
on
 .
2. Insert the supplied software CD into your CD-ROM drive.
If the installation window does not appear, click  Start > All programs > 
Accessories  > Run.
X:\ Setup.exe  repl
acing
  “X” with the letter, which represents your 
CD-ROM drive and click  OK.
3. R
eview and accept the installation agreements in the installation win -
do
 w. Then, click Nex t.
4. Select  Newto
 rk connection on the Printer Connection Type  screen. 
Then, click  Next.
5. F
ollow the instructions in the installation window.
 You can select the software applications in the  Select Software to 
Install  Window.
Silent installation Mode (Windows only)
Silent installation mode is an insta llation method that does not require 
any user intervention. On ce you start the installation, the machine driver 
and software are automatically inst alled on you computer. You can start 
the silent installation by typing  /s or  /S in the command window (See 
Silent installation Mode (Windows only) on page  32).
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 39
Mac
1.Make sure that the machine is connected to your network and powered 
on. Also, your machine’s IP address should have been set. 
2. In
sert the supplied software CD into your CD-ROM drive.
3.Doub
le-click the CD-ROM icon that appears on your Mac desktop.
4.Doub
le-click the MAC_Installer  folder.
5. Doub
le-click the Installer OS X  icon.
6. Enter the
  password and click  OK.
7. The
 Samsung Installer window opens. Click  Continue.
8. Read
 the license agreement and click  Continue.
9. Click  Agr
 ee to agree to the license agreement.
10. The
 Samsung Installer window opens. Click  Continue.
11. Select  Easy Insta
 ll and click  Install. Easy Install  is recommended for 
most users. All components necessary for machine operations will be 
installed. 
• If you select  Cu
 stom Install, you can choose individual components 
to install.
12. The
 message which warns that all applications will close on your com-
puter appears. Click  Cont
 inue.
 If you select  Typical installation for a network printer  during the 
machine driver installation, the  SetIP program automatically runs. 
If the machine has already configured network information, close 
the SetIP program. Go to the next step.
13. After th
e installation is finished, click  Quit.
14. Ope
n the Applications  folder > Utilities > Print Setup Utility .
• Fo
r Mac OS X 10.5~10.8, open the  Applications folder > System 
Preferences  and click Print & Fax .
15. Click  Add on th
 e Printer List .
• Fo
r Mac OS X 10.5~10.8, click the “ +” icon; a display window will pop 
up. 
16. For Mac OS X 
 10.3, select the IP Printing tab. 
• Fo
r Mac OS X 10.4, click  IP Printer.
• Fo
r Mac OS X 10.5~10.8, click  IP.
17. Select  Sock
 et/HP Jet Direct  in Printer Type .
 When printing a document containing many pages, printing perfor -
mance may be enhanced by choosing  So
 cket for Printer Type  
option.
18. Enter the
  machine’s IP address in the  Printer Address field.
19. Enter the q
 ueue name in the  Queue Name field. If you cannot determine 
the queue name for your machine server, try using the default queue 
first.
20. For Mac OS X 
 10.3, if Auto Select  does not work properly, select  Sam-
sung  in
  Printer Model  and your machine name in  Model Name.
• Fo
r Mac OS X 10.4, if Auto Select does not work properly, select 
Samsung  in Print Using  and your machine name in  Model. 
• Fo
r Mac OS X 10.5~10.8, if Auto Select does not work properly, 
select  Select a driver to use...  and your machine name in  Print 
Using . 
Your machine appears on the  Printer List, 
 and is set as the default 
machine.
21. Click  Add.
 If the printer driver does not work properly, uninstall the driver and 
reinstall it. 
Follow steps below to uninstall the driver for Mac. a)
Ma
ke sure that the machine is connected to your computer and 
powered on.
b) In
sert the supplied software CD into your CD-ROM drive.
c)Doub
le-click CD-ROM icon that appears on your Mac desktop.
d)Doub
le-click the  MAC_Installer folder.
e) Doub
le-click the  Installer OS X icon.
f) Ente
r the password and click  OK.
g) The
 Samsung Installer window opens. Click  Continue.
h) Select  Unins
 tall and click Uninstall . 
i) Whe
n the message which warns that all applications will close 
on your computer appears, Click  Continue.
j) Whe
n the uninstall is done, click  Quit.
Linux
Install Linux Driver
1.Make sure that the machine is connected to your network and pow -
ered on. Also, your machine’s IP address should have been set. 
2. From th
e Samsung website, download the Unified Linux Driver pack -
age to your computer.
3. Righ
t click the  Unified Linux Driver package and extract the pack -
age. 
4. Doub
le click  cdroot > autorun .
5. The
 Samsung Installer window opens. Click  Continue.
6. The
 Add printer wizard window opens. Click  Next.
7. Select Network printer and
  click Search  button.
8. The
 Printer’s IP address and model name appears on list field.
9.Select y
 our machine and click  Next.
10. In
put the printer description and  Next.
11. Whe
n the add printer is done, click  Finish.
12. Whe
n the install is done, click  Finish.
Add network Printer
1.Double-click the Unified Driver Configurator .
2. Click  Add Printer…
3. The
  Add printer wizard  window opens. Click  Next.
4. Select  Ne
 twork printer  and click the  Search button.
5. The
 printer’s IP address and model name appears on list field.
6.Select y
 our machine and click  Next.
7. In
put the printer description and  Next.
8. Whe
n the add printer is done, click  Finish.
UNIX
To use UNIX Printer Driver, you have to  install the UNIX printer driver pack-
age first, then setup the printer. You can download the UNIX Printer Driver 
pa
 ckage from the Samsung website.
Installing the UNIX printer driver package
Installation procedure is common for all variants of UNIX OS mentioned 
(See  UNIX on page  32 ).
1. From 
the Samsung website, download and unpack the UNIX Printer 
Driver package to  your computer.
2. Acq
uire root privileges. 
su -
3. Copy 
appropriate driver archiv e to the target UNIX computer.
 See administration guide of your UNIX OS for details.
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 40
4.Unpack the UNIX printer driver package archive.
For example, on IBM AIX use the following commands.
cd /tmp
gzip –dc /cdrom/unix/packages/aix_power/aix_power.tar.gz | tar 
–xv
 f –
The “ bi
naries” folder consists of  binz, install , share  files and folders
5. Cop
y the “ binaries” folder to any local folder.
6. Cha
nge to the driver’s “ binaries” directory.
cd aix_power/binaries
7. Run
 the install script.
./install
install  is the
  installer script file which is  used to install or uninstall the 
UNIX Printer Driver package.
Use “ ch
mod 755 install ” command to give the permission to the 
installer script.
8. Execute th
 e “. /install –c ” command to verify install results.
9. Run
 ‘ installprinter ’ from the command line. This will bring up the 
Add Printer Wizard  window. Setup the printer in this window refer -
ring the procedure next.
 On some UNIX OS, for example on Solaris 10 just added 
printer may not be enabled and/or may not accept jobs. In this 
case run the following two commands on the root terminal:
accept 
enable 
Uninstalling the printer driver package
 The uninstalling printer utility should be used to delete the printer 
installed in the system.
a) Run
 “ uninstallprinter ” command from the terminal.
It will open the  Uni
 nstall Printer Wizard
The installed printers are listed in the drop-down list
b) Sele
ct the printer to be deleted.
c)Cli
ck  Delete to delete the printer from the system.
d) Execute th
 e “. /install –d ” command to uninstall the whole 
package.
e) To
 verify uninstall results, execute the “ . /install –c” command.
To reinstall it again, use the command “ . /i
 nstall” to reinstall the binaries.
Setting up the printer
To add the printer to your UNIX system, run ‘installprinter’ from the com -
mand line. This will bring up the Add Printer Wizard window. Setup the 
printer in this wind
 ow according to the following steps:
1. Typ
e the name of the printer.
2.Sele
ct appropriate printer model from model list.
3.Enter any descriptio
 n corresponding to the type of the printer in the 
Type  field. This is optional.
4. Speci
fy any printer description in the  Description field. This is 
optional.
5. Speci
fy printer location in the  Location field.
6. Typ
e the IP address or DNS name of the printer in the  Device text-
box for network-connected printers. On IBM AIX with  je
 tdirect 
Queue type  only DNS name is possible, numeric IP address is not 
allowed.
7. Queue type  sh
 ows the connection as  lpd or jetdirect  in the corre -
sponding list box. Additionally us
 b type is available on Sun Solaris 
OS.
8. Select  Copies to 
 set the number of copies. 9.
Check th
 e Collate option to receive copies already sorted.
10. Check th
 e Reverse Order  option to receive copies in the reverse 
order.
11. Check th
 e Make Default  option to set this printer as default.
12. Click  OK to add
  the printer.
IPV6 CONFIGURATION
 
TCP/IPv6 is supported properly only  in Windows Vista or higher.
 If the IPv6 network seems to not be  working, set all the network setting 
to the factory defaults and try again (See  Restoring factory default 
settings using SyncThru™ Web Service on page  38 ).
To use the IPv6 network environment,  fol
 low the next procedure to use the 
IPv6 address:
1. C
onnect your machine to the network with a network cable.
2.T
urn on the machine.
3.Print a  Con
 figuration Report  from the machine’s control panel that will 
check IPv6 addresses (see  Printing configuration report on page  36 ).
4. Select  Start > Control Pa
 nel > Hardware and Sound  > Printers  > Add 
Printer .
5. Click  Ad
 d a local printer  on the Add Printer  windows.
6. F
ollow the instruction on the window.
 If the machine does not work in  the network environment, activate 
IPv6. Refer to the next section followed by.
Activating IPv6
1. Press  Menu on the control panel.
2. Pre
ss the up/down arrow to highlight  Network and press  OK.
3. Pre
ss the up/down arrow to highlight  TCP/IP (IPv6) and press OK.
4. Pre
ss the up/down arrow to highlight  IPv6 Activate and press OK.
5. Pre
ss the up/down arrow to highlight  On and press  OK.
6. T
urn the machine off and turn it on again.
7.R
einstall your printer driver.
Setting IPv6 addresses
Machine supports following IPv6 addresses for network printing and man -
agements.
• L
ink-local Address : Self-configured local IPv6  address. (Address starts 
with FE80.)
• Stat
eless Address : Automatically configured IPv6 address by a net -
work router.
• Stat
eful Address : IPv6 address configured by a DHCPv6 server.
• Ma
nual Address : Manually configured IPv6 address by a user.
DHCPv6 address configuration (Stateful)
If you have a DHCPv6 server on your network, you can set one of the 
following option for default dynamic host configuration:
1.Pr
ess  Menu on the control panel.
2. Pre
ss the up/down arrow to highlight  Network and press  OK.
3. Pre
ss the up/down arrow to highlight  TCP/IP (IPv6) and press OK.
4. Pre
ss the up/down arrow to highlight  DHCPv6 Config and press 
OK .
5. Pre
ss the up/down arrow to access the required value.
•Router : Use DHCPv6 on
 ly when requested by a router.
• DHCPv
6 Addresses : Always use DHCPv6 regardless of router 
Downloaded From ManualsPrinter.com Manuals