Samsung ML 6510ND User Manual

							Safety information_ 11
Maintenance / Checking
 Caution
Unplug this product from the wall outlet before 
cleaning the inside of the machine.  Do not clean 
 the 
machine with benzene, paint thinner or alcohol; do 
not spray water directly into the machine. 
►  This could result in electric shock or fire. 
Keep cleaning supplies away from children. 
►  Children could get hurt.
When you are working inside the machine replacing 
supplies or cleaning the in side, 
 do not operate the 
machine.
►  You could get injured.
Do not disassemble, repair or rebuild the machine by 
yourself. 
►  It can damage the machine. Call a certified 
tech nicia

n when the machine needs repair.
Keep the power cable and the contact surface of the plug clean 
from dust or water.
►  Otherwise, this could result  in electric shock or 
 fire. 
To clean and operate the machine, strictly follow the users 
guide provided with the machine.
►  Otherwise, you could damage the machine.
•  Do not remove any covers or guards that are fastened with 
screws. 
•  F
user units should only be repaired by a certified service 
techni
 cian. Repair by non-certif ied technicians could result in 
fire or electric shock.
►  The machine should only be repaired by a Samsung service 
techni ci

an.
Supply usage
 Caution
Do not disassemble the toner cartridge.
► Toner dust can be dangerous if inhaled or 
i n

gested.
When storing supplies such as toner cartridges, keep 
them away from children.
►  Toner dust can be dangerous if inhaled or 
inge sted

.
Do not burn any of the supplies such as toner 
cartridge or fuser unit.
► This could cause an explosion or uncontrollable 
fi re

.
Using recycled supplies, such as toner, can cause damage to 
the machine.
►  In case of damage due to the use of recycled supplies, a 
service  

fee will be charged.
Downloaded From ManualsPrinter.com Manuals 
						

							Safety information_ 12
For supplies that contain tone r dust (toner cartridge, waste 
toner bottle, imaging unit, etc.)  foll
 ow the instructions below.
• When disposing of the supplies, follow the instructions for 
disp
 osal. Refer to the reseller for disposal instructions.
• Do not wash the supplies.
• For a waste toner bottle, do not reuse it after emptying the bottle.
►  If 

you do not follow the instructions above, it may cause 
mach ine malfun

ction and environmental pollution.  The 
warranty does not cover damages caused by a users 
carelessness.
When changing the toner cartridge or removing jammed paper, 
be careful not to let toner dust touch your body or clothes.
►  Toner dust can be dangerous if inhaled or ingested.
When toner gets on your clothing, do not use hot water to wash 
it. 
►  Hot water sets toner into fabric. Use cold water. 
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 13
regulatory information
This machine is designed for our sound environment and certified with  several regulatory statements.
LASER SAFETY STATEMENT
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for Class I(1) laser  products, and 
elsewhere is certified as a Class I laser product conforming  to the requirements of IEC 60825-1:1993 + A1:1997 + A2:2001.
Class I laser products are not considered  to be 
hazardous. The laser 
 system and printer are designed so there is never any human access to 
laser radiation above a Class I level during normal operati on, user maintenance or prescribed service condition.
ML-551x Series
• Wav elength : 800 nm
• Beam d i
 vergence
- Paraller : 12 degrees
- Perp endicular : 35
  degrees
• Maximum power or energy output : 15 mW
ML
 -651x Series
• Wav
elength : 800 nm
• Beam d i
 vergence
- Paraller : 12 degrees
- Perp endicular : 35
  degrees
• Maximum power or energy output : 10 mW
WARNING 
Never operate or service the printer with t he protective cover removed from Laser/Sca nner assembly. The reflected beam, although invisible, 
can damage your eyes.
When using this product, these basic safety precautions should al ways be followed to 
 reduce risk of fire, electric shock, and injury to persons:
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 14
OZONE SAFETY
During normal operation, this machine produces ozone. The ozone produced does not present a hazard to the operator. However, it is advis-
able that the machine be oper ated 
 in a well ventilated area.
If you need additional information about ozone, request your nearest Samsung dealer.
MERCURY SAFETY
Contains Mercury, Dispose According to Lo cal, State or Federal Laws.(U.S.A. only)
POWER SAVER
This printer contains advanced energy conservation technology th at reduces power consumption when it is not in active use.
When the printer does not receive data for an extended perio d of time, powe
 r consumption is automatically lowered. 
ENERGY STAR and the ENERGY STAR  mark are reg
 istered U.S. marks. 
For more information on the ENERGY ST AR program
  see http://www.energystar.gov
RECYCLING
Recycle or dispose of the packaging material for this product in an environmentally responsible manner.
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 15
CHINA ONLY
Dan hab yungh youq gij digih haijbaz 2000 m doxroengz haenx ancienz sawj\
yungh.
2000m
CORRECT DISPOSAL OF THIS PRODUCT (WASTE ELECTRICAL & ELECTRONIC EQUIPMENT)
(Applicable in the with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger,  headset, USB 
cable) should not be disposed of  with other household waste at the end of their working life. To prevent possible harm to the e nvironment or 
human health from uncontrolled waste disposal, please separate  these items from other types of waste and recycle them responsib ly to pro-
mote the sustainable reuse of material resources.
Household users should contact either the re tailer wh
 ere they purchased this product, or their local government office, for det ails of where and 
how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and  con
 ditions of the purchase contract. This product and its electronic 
accessories should not be mixed with other commercial wastes for disposal.
CORRECT DISPOSAL OF BAT TERIES IN THIS PRODUCT
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that  the batteries in this product should not be disposed with other  household 
waste at the end of their workin g life. Where marked, the chemical symbols Hg, Cd  or Pb indicate that the battery contains mercury, cadmium 
or lead above the reference levels in EC Directive 2006/66. If  batteries are not properly disposed of, these substances can cau se harm to 
human health or the environment. To protect natural resources and  to promote material reuse, please separate batteries from other types of 
waste and recycle them through your local, free battery return system.
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 16
STATE OF CALIFORNIA PROPOSITION 65 WARNING (US ONLY)
RADIO FREQUENCY EMISSIONS
FCC Information to the User
This device complies with Part 15 of  the FCC Rules. Operation is subject to the following two conditions: 
• This device may not cause harmful interference, and
• This  device must accept  any in
 terference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limit s for 
 a Class A digital device, pursuant to Part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection against harmf ul interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if  not installed and used in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no  guarantee that interference will not occur in a particular installation. If this equ ipment does cause 
harmful interference to radio or television reception, which can  be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures:
• Reorie
nt or relocate the receiving antenna.
• Incre ase the separation between the equipment and receiver.
• Conn ect the equipment into an outlet on a circuit diff ere
 nt from that to which the receiver is connected.
• Consul t the dealer or experienced radio TV technician for help.
 Change or modifications not expressly approv ed by the manufacturer responsible for compliance could void the users authority to oper-
ate the equipment.
Canadian Radio Interference Regulations
This digital apparatus does not exceed the Class A limits for radi o noise emissions from digital apparatus as set out in the interference-causing 
equipment standard entitled “Digital Apparatus” , ICES-003 of the Industry and Science Canada.
Cet appareil numérique respecte les limites de bruits radioélectri ques ap
 plicables aux appareils numériques de Classe A prescrites dans la 
norme sur le matériel brouilleur: “Appareils Numériques”, ICES-003 édictée  par l’Industrie et Sciences Canada.
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 17
UNITED STATES OF AMERICA
Federal Communications Commission (FCC)
Intentional emitter per FCC Part 15
Low power, Radio LAN type devices (radio frequency (RF) wireless co mmunication devices), operating in the 2.4 GHz/5 GHz Band, may be 
present (embedded) in your printer system. Th is section is only applicable if these devices are present. Refer to the system la bel to verify the 
presence of wireless devices.
Wireless devices that may be in your system are only qualified for  use in the United
 
 States of America if an FCC ID number is o n the system 
label.
The FCC has set a general guideline of 20 cm (8 inches) separa tion betwee
 n the device and the body, for use of a wireless device near the 
body (this does not include extremities). This device should be  used more than 20 cm (8 inches) from the body when wireless dev ices are on. 
The power output of the wireless device (or de vices), which may be embedded in your printer, is well below the RF exposure limits as set by 
the FCC.
This transmitter must not be collocated or operatio n
 
 in conjunction with any other antenna or transmitter.
Operation of this device is subject to the following two condit ions: (1) Th
 is device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference  that may cause undesired operation of the device.
 
Wireless devices are not user serviceable. Do not modify them  in any way. Modification to a wireless device will void the autho rization to 
use it. Contact manufacturer for service.
FCC Statement for Wireless LAN use:
 
While installing and operating this transmitter and antenna combin ation the radio frequency exposure limit of 1m W/cm2 may be 
exceeded at distances close to the antenna installed. Therefore,  the user must maintain a minimum distance of 20cm from the ant enna at 
all times. This device cannot be colocated wi th another transmitter and transmitting antenna.
RUSSIA ONLY
GERMANY ONLY
ISRAEL ONLY
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 18
TURKISH ONLY
REPLACING THE FITTED PLUG (FOR UK ONLY)
Important
The mains lead for this machine is fitted with a standard (BS 1363)  13 amp plug and has a 13 amp fuse. When you change or examine the 
fuse, you must re-fit the correct 13 amp fuse. You then need to  replace the fuse cover. If you have lost the fuse cover, do not use the plug until 
you have another  fuse cover. 
Contact the people from you purchased the machine.
The 13 amp plug is the most widely used type in the UK and should  be suitabl
e. 
 However, some buildings (mainly old ones) do not have normal 
13 amp plug sockets. You need to buy a suitable plug adaptor. Do not remove the moulded plug.
 
If you cut off the moulded plug,  get rid of it straight away.
You cannot rewire the plug and you may receive an  electric shock if you
  plug it into a socket.
Important warning: 
You must earth this machine.
The wires in the mains lead have the following color code:
•Green and Yellow:  Ea
 rth
• Blue:  Neutral
• Brow
n: Li
 ve
If the wires in the mains lead do not match the colors marked in your plug, do the following:
You must connect the green and yellow wire to the pin marked by the lette
 r “E” or by the safety ‘Earth symbol’ or colored green and yellow or 
green.
You must connect the blue wire to the pin whic h
 
 is marked with the letter “N” or colored black.
You must connect the brown wire to the pin wh ich is marked with the letter 
 “L” or colored red.
You must have a 13 amp fuse in the plug,  a
 daptor, or at the distribution board.
DECLARATION OF CONFORMITY (EUROPEAN COUNTRIES)
Approvals and Certifications
The CE marking applied to this product symbolizes Samsung Electron ics Co., Ltd. Declaration of Conformity with the following applicable 
93/68/EEC Directives of the European  Union as of the dates indicated:
Hereby, Samsung Electronics declare that this  
prod
 uct is in compliance with the essential requirements and other relevant provisions of:
ML-551x Series, ML-651x Series:  R&TTE Directive (1999/5/EC)
The declaration of conformity may be consulted at www.samsung.com/printer , go to Support > Download center and enter your printer (MFP) 
name to browse the EuDoC. 
January 1, 1995:  Council Directive 2006/95/EC Approximation of the laws of  
the member state
 s related to low voltage equipment.
January 1, 1996:  Council Directive 2004/108/EC (92/31/EEC),  appro
 ximation of the laws of the Member States related to electromagnetic 
compatibility.
March 9, 1999:  Council Directive 1999/5/EC on radio equipment and telecommu n
ications terminal
  equipment and the mutual recognition of 
their conformity. A full declaration, defining the relevant Direc tives and referenced standards can be obtained from your Samsu ng Electronics 
Co., Ltd. representative.
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 19
European Radio Approval Information (for products fitted with EU-approved radio devices)
Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz/5 GHz band, may be 
present (embedded) in your printer system, which is intended for home or office use. This section is only applicable if these devices are pres -
ent. Refer to the system  label to verify the pres
 ence of wireless devices.
Wireless devices that may be in your system are only qualified fo r use in the European Uni
 on or associated areas if a CE mark 
with 
 a Notified Body Registration Number and  the Alert Symbol is on the system label.
The power output of the wireless device or devices that may be embed ded
  in you printer is well below the RF exposure limits as set by the 
European Commission through the R&TTE directive.
European States qualified under wireless approvals:
EU
Austria, Belgium, Cyprus, Czech Republic, Den m
 ark, Estonia, Finland, France (with frequency restrictions), Germany, Greece, Hun gary, Ire-
land, Italy, Latvia, Lithuania,  Luxem
 bourg, Malta, The Netherlands, Poland, Port ugal, Slovakia, Slovenia, Spain, Sweden and the  U.K.
EEA/EFTA countries
Iceland, Liechtenstein, Norway and Switzerland
European States with restrictions on use:
• EU:  In France, the frequency range is restricted to 2446.5-2483.5 MHz  for de vices above 10 mW transmitting power such as wireless
• EEA /EFTA countries:  No li
 mitations at this time
REGULATORY COMPLIANCE STATEMENTS
Wireless Guidance
Low power, Radio LAN type devices (radio frequency (RF) wireless co mmunication devices), operating in the 2.4 GHz/5 GHz Band, may be 
present (embedded) in your printer system. Th e following section is a general overview of considerations while operating a wire less device.
Additional limitations, cautions, and concer ns for sp
 ecific countries are listed in the specific country sections (or country g roup sections). The 
wireless devices in your system are only qu alified for use in the countries identified by the Radio  Approval Marks on the syste m rating label. If 
the country you will be using the wireless device in, is not li sted, contact your local Radio Approval agency for requirements. Wireless devices 
are closely regulated and use may not be allowed.
The power output of the wireless device or devices that may be em b
edd
 ed in your printer is well below the RF exposure limits as known at this 
time. Because the wireless devices (which may be embedded into  your printer) emit less energy than is allowed in radio frequency safety stan-
dards and recommendations, manufacturer believes these devices are sa fe
 
 for use. Regardless of the power levels, care should be taken to 
minimize human contact during normal operation.
As a general guideline, a separation of 20 cm (8 inches) betw een the
  wireless device and the body, for use of a wireless device near the body 
(this does not include extremities) is typical. This device should  be used more than 20 cm (8 inches) from the body when wirele ss devices are 
on and transmitting.
This transmitter must not be collocated or operatio n
 
 in conjunction with any other antenna or transmitter.
Some circumstances require restrictions on wireless device s. E
 xamples of common restrictions are listed below:
Radio frequency wireless communication can interfere with equipment on commercial aircraft. Current aviation regulations requir e wireless 
devices to be turned off while traveling in an airplane. IEEE 802.11  (also known as wireless Ethernet) and Bluetooth communication devices 
are examples of devices that  provide wireless communication.
In environments where the risk of interference to other devices or  services is harmful or perceived as harmful, the option to use a wireless 
device may be restricted or eliminated. Airports, Hospitals,  and Oxygen or flammable gas laden atmospheres are limited examples  where use 
of wireless devices may be restricted or eliminated. When in envi ronments where you are uncertain of the sanction to use wireless devices, 
ask the applicable authority fo r authorization prior to use or turning on the wireless device.
Every country has different rest rictions on the use of wireless devices. Since your system  is equipped with a wireless device, when traveling 
between countries with your  system, check with the local Radio Approval authorit ies prior to any move or trip for any restrictions on the use of 
a wireless device in the destination country.
If your system came equipped with an internal embedded wireless de vice, do not operate the wireless device unless all covers and shields are 
in place and the system is fully assembled.
Wireless devices are not user serviceable. Do  not modify them in any way. Modification to a wireless device will void the autho rization to use it. 
Contact manufacturer for service.
Only use drivers approved for the country in which the device will  be used. See the manufacturer System Restoration Kit, or contact manufac-
turer Technical Support for additional information.
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 20
OPENSSL LICENSE
Copyright (c) 1998-2001 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or wi th
 out modification, are permitted provided that the following cond itions are met:
1. Redi
stributions of source code must retain the above copyright  notice, this list of conditions and the following disclaimer.
2. Redi
stributions in binary form must reproduc e the above copyright notice, this list of conditions and the following disclaimer  in the documen-
tation and/or other materials provided with the distribution.
3. Al
l advertising materials mentio ning features or use of this software must di splay the following acknowledgment: This product  includes 
software developed by the OpenSSL Project for use  in the OpenSSL Toolkit. (http://www.openssl.org/)
4. The
 names OpenSSL Toolkit and OpenSSL Project must not be used  to endorse or promote products derived from this software without
5. P
rior written permission. For  written permission, please contact [email protected].
6. Pro
ducts derived from this software may not be called OpenSSL  nor may OpenSSL appear in their names without prior written permis-
sion of the OpenSSL Project.
7. Redi
stributions of any form whatsoever must retain the following  acknowledgment: This product includes software developed by the 
OpenSSL Project for use in the Open SSL Toolkit (http://www.openssl.org/)
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS  IS AND ANY 
 EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, 
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DIS-
CLAIMED. IN NO EVENT SHALL TH E 
 OpenSSL PROJECT OR ITS CONTRIBUTORS BE  LIABLE FOR ANY DIRECT, INDIRECT, INCIDEN-
TAL, SPECIAL, EXEMPLARY, OR CONSEQUENT IAL DAMAGES (INCLUDING, BUT NOT LIMITED  TO, PROCUREMENT OF SUBSTITUTE 
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTE RRUPTION) HOWEVER CAUSED AND ON ANY THE-
ORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABIL
 ITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN 
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN  IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic softwa re
  written by Eric Young([email protected]). This product includes software written b y Tim Hudson 
([email protected]).
ORIGINAL SSLEAY LICENSE
Copyright (C) 1995-1998 Eric Young (eay @cryptsoft.com) All rights reserved.
This package is an SSL implementation writte n by 
 Eric Young ([email protected]). The implementation was written so as to confor m with 
Netscapes SSL.
This library is free for commercial and non-commercial use  as lo
 ng as the following conditions are aheared to. The following conditions apply to 
all code found in this distribution, be it  the RC4, RSA, lhash, DES, etc., code; not  just the SSL code. The SSL documentation i ncluded with this 
distribution is covered by the same copyright terms except that  the holder is Tim Hudson ([email protected]). Copyright remains  Eric Youngs, 
and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be  given attribu-
tion as the author of the parts of the lib rary u
 sed. This can be in the form of a textual message at program startup or in docu mentation (online 
or textual) provided with the package.
Redistribution and use in source and binary forms, with or wi th
 out modification, are permitted provided that the following cond itions are met:
1. Redi
stributions of source code must reta in the copyright notice, this list of conditions and the following disclaimer.
2. Redi
stributions in binary form must reproduc e the above copyright notice, this list of conditions and the following disclaimer  in the documen-
tation and/or other materials provided with the distribution.
3. Al
l advertising materials mentio ning features or use of this software must di splay the following acknowledgement: This product  includes 
cryptographic software written by Eric Young ([email protected])  The word cryptographic can be left out if the routines from the library 
being used are not cryptographic related:-).
4. If 
you include any Windows specific code (or a derivative thereo f) from the apps directory (application code) you must include an acknowl -
edgement: This product includes software writ te
 n by Tim Hudson ([email protected])
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS AN D ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 
 LIM-
ITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  FITNESS 
 FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN 
NO EVENT SHALL THE AUTHOR OR CONTRI BUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, 
OR CONSEQUENTIAL DAMAGES (INCLUDING , BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, 
WHETHER IN CONTRACT, STRICT LIABILITY,  OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF 
THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publicly available vers ion
  or derivative of this code cannot be changed. i.e. this code cannot simply 
be copied and put under another distribution  licence [including the GNU Public Licence.
Downloaded From ManualsPrinter.com Manuals