Samsung LT-P326W TFL LCD Television User Manual

							English-68
OPERATION
Color Weakness
This feature enables those with a color weakness to view images as
those with normal color vision do.The feature provides nine different color adjustment
layers for red, green and blue.
1
Press the MENUbutton to
display the on-screen menu.
Press the 
UP/DOWNbuttons to select “Setup”, then
press the ENTERbutton.
2
Press the UP/DOWNbuttons to select 
“Color Weakness”, then press
the 
ENTERbutton.
3
Press the ENTERbutton and then press 
the UP/DOWNbuttons to select 
“On”, then press 
the 
ENTERbutton.
4
Press the UP/DOWNbuttons to select 
“Red”, “Green”, “Blue”.
Press the 
LEFT/RIGHT
buttons to decrease or
increase the value of
a particular item.
Press the 
EXITbutton 
to exit.
This function doesn’t work 
when the Source is in PC mode, 
or DNIe is in off mode.
BN68-00653A-01Eng.qxd  5/7/04 9:06 AM  Page 68 
						

							English-69
OPERATION
Selecting the Melody
You can hear a melody sound when the television is powered on or off.
1
Press the MENUbutton to
display the on-screen menu.
Press the 
UP/DOWNbuttons to select “Setup”,
then press the ENTERbutton.
3
Press the UP/DOWNbuttons to select
“Off” or “On”. 
Press the 
EXITbutton 
to exit.
2
Press the UP/DOWNbuttons to select 
“Melody”, then press
the 
ENTERbutton.
BN68-00653A-01Eng.qxd  5/7/04 9:06 AM  Page 69 
						

							English-70
Chapter Five
PC DISPLAY
Using Your TV as a Computer (PC) Display
How to Set up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below.
However, the actual screens on your PC will probably look different, depending upon
your particular version of Windows and your particular video card. Even if your actual
screens look different, the same, basic set-up information will apply in most cases.
(If not, contact your computer manufacturer or Samsung Dealer).
First, click on “Settings” on the
Windows start menu.
While “Settings” is highlighted,
move the cursor so that “Control
Panel” is highlighted.
When the control panel screen
appears, click on “Display” and a
display dialog-box will appear.
Navigate to the “settings” tab on
the display dialog-box.
The two key variables that apply
the TV-PC interface are “resolution”
and “colors.” The correct settings
for these two variables are:
* Size 
(sometimes called “resolution”):
1280 x 768 pixels
If a vertical-frequency option exists
on your display settings dialog box,
the correct value is “60” or “60 Hz”.
Otherwise, just click “OK” and exit
the dialog box.
* See “Display Modes” on page 87.
BN68-00653A-01Eng.qxd  5/7/04 9:06 AM  Page 70 
						

							English-71
How to Auto Adjust
Use the Auto Adjust function to have the TV set automatically adjust the video signals
the monitor receives.   The function also automatically fine-tunes the settings and
adjusts the frequency values and positions.  
Press the PC button on the remote control to select the PC mode.
PC DISPLAY
1
Press the MENUbutton to
display the menu.
Press the 
UP/DOWNbuttons to select “Setup”,
then press the ENTERbutton.
Press the 
UP/DOWNbuttons to select
“PC”, then press
the 
ENTERbutton.
2
Press the UP/DOWNbuttons to select
“Auto Adjust”,
then press the 
ENTERbutton.
BN68-00653A-01Eng.qxd  5/7/04 9:06 AM  Page 71 
						

							English-72
Adjusting the Screen Quality
The purpose of the picture quality adjustment is to remove or reduce picture noise.
If the noise is not removed by fine tuning alone, then do the frequency adjustments to
the utmost and fine tune again. After the noise has been reduced, re-adjust the picture
so that it is aligned on the center of screen.
Press the PC button on the remote control to select the PC mode.
Note:This function does not work in DVI-Digital mode.
PC DISPLAY
2
Press the ENTERbutton to select
“Image Lock”.
1
Press the MENUbutton to
display the menu.
Press the 
UP/DOWNbuttons to select “Setup”,
then press the 
ENTERbutton.
Press the 
UP/DOWNbuttons to select 
“PC” then press the
ENTERbutton.
3
Press the UP/DOWN
buttons to select
“Coarse” or “Fine”,
then press the
ENTERbutton.
Press the
LEFT/RIGHTbuttons to adjust the
screen quality, vertical
stripes may appear or the
picture may be blurry.
Press the 
EXITbutton to
exit.


BN68-00653A-01Eng.qxd  5/7/04 9:06 AM  Page 72 
						

							English-73
Changing the Screen Position
Press the PC button on the remote control to select the PC mode.
PC DISPLAY
2
Press the UP/DOWNbuttons to select
“PC”, then press
the 
ENTERbutton.
Press the 
UP/DOWNbuttons to select
“Position”, then press
the 
ENTERbutton.
1
Press the MENUbutton to
display the menu.
Press the 
UP/DOWNbuttons to select “Setup”,
then press the ENTERbutton.
3Press the UP/DOWNbuttons to adjust
the V-Position.
Press the 
LEFT/RIGHTbuttons to adjust
the H-Position.
Press the 
EXITbutton 
to exit.
BN68-00653A-01Eng.qxd  5/7/04 9:06 AM  Page 73 
						

							English-74
To Initialize the Screen Position or Color Settings
Press the PC button on the remote control to select the PC mode.
PC DISPLAY
2
Press the UP/DOWNbuttons to select
“Image Reset”, then press
the 
ENTERbutton.
Press the 
EXITbutton 
to exit.
1
Press the MENUbutton 
to display the menu.
Press the 
UP/DOWNbuttons to select “Setup”,
then press the ENTERbutton.
Press the 
UP/DOWNbuttons to select
“PC”, then press
the 
ENTERbutton.
BN68-00653A-01Eng.qxd  5/7/04 9:06 AM  Page 74 
						

							English-75
If the TV seems to have a problem, first try this list of possible problems and solutions.
If none of these troubleshooting tips apply, call your nearest Samsung service center.
Identifying Problems
Problem
Poor picture
Poor sound quality.
No picture or sound.
No sound or sound is too low
at maximum  volume.
Picture rolls vertically.
The TV operates erratically.
The TV won’t turn on.
Remote control malfunctions
“Check Signal Cable” 
message.
Possible Solution
Try another channel.
Adjust the antenna.
Check all wire connections.
Try another channel.
Adjust the antenna.
Try another channel.
Press the TV/VIDEO button.
Make sure the TV is plugged in.
Check the antenna connections.
First, check the volume of units connected to your TV
(digital broadcasting receiver, DTV, DVD, cable 
broadcasting receiver, VCR, etc.). Then, adjust the TV
volume accordingly.
Check all wire connections.
Unplug the TV for 30 seconds, then try operating it
again.
Make sure the wall outlet is working.
Replace the remote control batteries.
Clean the upper edge of the remote control
(transmission window).
Check the battery terminals.
Ensure that the signal cable is firmly connected to the
PC sources.
Chapter Six
TROUBLESHOOTING
BN68-00653A-01Eng.qxd  5/7/04 9:06 AM  Page 75 
						

							English-76
TROUBLESHOOTING
Problem
“Not Supported Mode!” 
message.
The image is too light or too
dark.
Horizontal bars appear to 
flicker, jitter or shimmer on
the image.
Vertical bars appear to flicker,
jitter or shimmer on the image.
Screen is black and power
indicator light blinks steadily.
Image is not stable and may
appear to vibrate.
Image is not centered on the
screen.
If a still image is displayed for
an extended period of time,
residual images or blurring
may appear. 
Possible Solution
Check the maximum resolution and the frequency of
the Video Adapter.
Compare these values with the data in the Display
Modes Timing Chart.
Adjust the Brightness and Contrast.
Adjust the Fine tuning.
Adjust the Coarse tuning and then adjust the Fine
tuning.
Adjust the Coarse tuning and then adjust the Fine
tuning.
On your computer check: Power , 
Signal Cable(24-pin DVI)
The TV is using its power management system. 
Move the computer's mouse or press a key on the keyboard. 
If the setting is not correct, use your computer utility
program to change the display settings.
NOTE: Your TV supports multiscan display functions
within the following frequency domain:
• Horizontal frequency: 30 kHz ~ 61 kHz
• Vertical frequency: 56 Hz ~ 75 Hz
• Maximum refresh rate: 1280 x 768 @ 60 Hz
Adjust the horizontal and vertical position.
The screen position must be adjusted on the output
source(i.e.. STB) with a digital signal.
When you need to leave the monitor unused for an
extended period of time, adjust the settings so that the
monitor automatically goes into energy saving mode or
activates the screen saver to display moving images.
BN68-00653A-01Eng.qxd  5/7/04 9:06 AM  Page 76 
						

							English-77
TROUBLESHOOTING
Problem Possible Solution
The Anynet does not function. Check to see if the device is an Anynet device.
The Anynet System supports only Anynet-enabled devices.
The Anynet System supports up to one device from the
Receiver product group and two devices from the DVD
product group. Check to see if the Anynet devices are plugged
in properly.
The remote control doesn’t
work.Check to see if the angle and the distance between the remote
control and the device are appropriate and if there is any obstacle
in the path between the remote control and the device.
Replace the remote control batteries.
Check to see if you selected the correct device (TV, DVD,
VCR, cable or STB) to control using the [Mode] button.
Check to see if the remote control mode matches the input mode.
See if you pressed the correct function button.
Be sure to note that there are buttons on the remote control
that are not available depending on the device mode.
I would like to start the
Anynet.See if the Anynet devices are connected to the TV according
to the connection diagram and make sure the proper Anynet
Connection Setting has been selected.
Press the [Mode] button on the TV remote control to
set the mode to TV.
Then, press the [Anynet] button to bring up the Anynet menu
and choose a what AV device you want to see.
I would like to exit the
Anynet.Press [TV/Input] button on the TV remote control.
Turn the TV off.
If you press the [Menu] button while you are using the Anynet
Watch function, it can bring up the DVD menu, VCR menu or
the Set-Top Box menu.
To view the TV menu, go to Anynet “Settings” and select
“TV Menu.”
Press the Menu button on the front of the TV.I would like to bring up the
TV menu while using the
Anynet.
BN68-00653A-01Eng.qxd  5/7/04 9:06 AM  Page 77