Samsung LT-P326W TFL LCD Television User Manual

							English-18
INSTALLATION
1. Antenna Cable: Connect the external antenna cable to the ANT IN port on the TV.
2. Anynet Connector: To use the Anynet, connect the Anynet port on the TV and the
Anynet Input port on the DVD Combo using the Stereo-Stereo Anynet connector.
3. AV Connector: If you do not have a Component cable, connect the A/V output jacks on the
DVD/VCR Combo to the AV IN jacks on the TV.
4. Component Cable (Sold Separately): If you have the component connector cable,
connect Component Video Out jacks (DVD only) on the DVD/VCR Combo to the Component 1
Video Input jacks on the TV.
5. Audio Cable: After you complete step 4, connect the Component Audio Output jacks (DVD only)
on the DVD/VCR Combo and the Component Input 1 L-Audio-R jacks on the TV.
3. Connecting TV + DVD/VCR Combo: 
Connecting AV Signal Cables
How to Connect the Cables (Connect in the order of numbers shown in the diagram.)
BN68-00653A-01Eng.qxd  5/7/04 9:03 AM  Page 18 
						

							English-19
INSTALLATION
1. Antenna Cable:Connect the external antenna cable to the ANT Input port of the TV.
2. Anynet Connectors:To use the Anynet,connect the Anynet port on the TV and the Anynet Input
port on the DVD Receiver using the Stereo-Stereo Anynet connector.
3. Video Connector:If you do not have the component connector, connect the Video Output port on
the DVD Receiver and the AV IN port on the TV.
4. Audio Connector:Connect the Left-Audio-Right port of Monitor Output on the TV and the Audio
Input port on the DVD Receiver.
5. Component Connector (Sold Separately):If you have the component connector,connect the
Color Difference Component Output port on the DVD Receiver and the Component Input 1
YpbPr port on the TV.
4. Connecting TV + DVD Receiver:
Connecting AV Signal Cables
How to Connect the Cables (Connect in the order of numbers shown in the diagram.)
BN68-00653A-01Eng.qxd  5/7/04 9:03 AM  Page 19 
						

							English-20
INSTALLATION
5. Connecting TV + DVD Combo + DVD Receiver:
Connecting AV Signal Cables
How to Connect the Cables (Connect in the order of numbers shown in the diagram.)
1. Antenna Cable: Connect the external antenna cable to the ANT IN port of the TV. 
2. Anynet Connectors: To use Anynet, connect the Anynet port on the TV and the Anynet Input port
on the DVD/VCR Combo using the Stereo-Stereo Anynet connector.
3. Anynet Connectors: To use Anynet, connect the Anynet Output port on the DVD/VCR Combo and
the Anynet Input port on the DVD Receiver using the Stereo-Stereo Anynet connector.
4. AV Cable: If you do not have the component connector, connect the Output port of the AV output
jacks on the DVD/VCR Combo to the AV IN jacks on the TV.
5. Component Connector (Sold Separately): If you have the component connector, Connect the
Component Video Output jacks (DVD only) on the DVD/VCR Combo and the Component Input 1
“Y, P
B, PR” jacks on the TV.
6. Audio Cable: Connect the L-Audio-R COMPONENT Audio In 1 jacks on the TV to the Analog
Audio Output jacks on the DVD/VCR Combo.
7. Component Cable (Sold Separately): Connect Component Video Out jacks on the DVD Receiver
to the COMPONENT Input 2 “Y, P
B, PR” jacks on the TV.
8. Audio Cable:Connect the Left-Audio-Right port of Audio Output on the TV and the Audio Input
port on the DVD Receiver.
9. Optical Cable (Sold Separately): If you have an optical cable, connect the Digital Audio Output
Optical port on the DVD/VCR Combo to theDigital Input port on the DVD Receiver. 
10.To enjoy 5.1-channel sound, go to “Set up” in the Anynet menu and select “Customized Setup”.
BN68-00653A-01Eng.qxd  5/7/04 9:03 AM  Page 20 
						

							English-21
Chapter Three
OPERATION
Changing Channels
Using the Channel Buttons
1
Press the CH /buttons to change channels. 
When you press the CH/buttons, the TV changes channels in sequence.
You will see all the channels that the TV has memorized. (The TV must have 
memorized at least three channels). You will not see channels that were either 
erased or not memorized.
Using the PRE-CH Button to select the Previous Channel
1
Press the PRE-CHbutton.The TV will switch to the last channel viewed.
To quickly switch between two channels that are far apart, tune to one channel,
then use the number button to select the second channel. Then use the PRE-CH
button to quickly alternate between them.
Adjusting the Volume
1
Press the VOL +/– buttons to increase or decrease the volume. 
1
Press MUTEand the sound cuts off. 
The word“” 
will appear in
the lower-left corner of the screen.
2
To turn mute off, press the MUTEbutton again, or simply
press the VOL +/-buttons.
Using Mute
At any time, you can temporarily cut off the sound using the Mute button.
Turning the TV On and Off
Press the POWERbutton.
You can also use the Power button on the front panel.
BN68-00653A-01Eng.qxd  5/7/04 9:03 AM  Page 21 
						

							English-22
OPERATION
Viewing the Display
The display identifies the current channel and the status
of certain audio-video settings.  
Viewing the Menus
The on-screen displays
disappear after about ten seconds.
Press the INFO button once more 
or wait approximately 10 seconds 
and it disappears automatically.
Allows the user to adjust the 
settings according to his/her 
preference and shows the 
current settings.1
Press the INFObutton on the
remote control.
The TV will display the
channel, the type of sound,
and the status of certain
picture and sound settings.
1
With the power on, press
the MENUbutton.
The main menu appears on
the screen. It’s left
side has five icons:
Input, Picture, Sound,
Channel, Setup. 
The on-screen menus
disappear from the screen after
about two minutes.
You can also use 
the 
MENU( ), CH Up/Down,
Volume Up/Down and
SOURCE(ENTER) buttons on the
TV to make selections.2
Use the UP/DOWNbuttons to select one of the 5 icons. 
Then press 
ENTERto access the icon’s sub-menu.
3
Press the MENUbutton to exit.
BN68-00653A-01Eng.qxd  5/7/04 9:03 AM  Page 22 
						

							English-23
Setting Up Your Remote Control
After it has been set up properly, your remote control can operate in five different modes:
TV, VCR, Cable, DVD or Samsung Set-top box. Pressing the corresponding button on the
remote control allows you to switch between these modes, and control whichever piece of
equipment you choose.
Note
The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.
This remote control is only compatible with Samsung Set-top boxes.
Note on Using Remote Control Modes: VCR
When your remote control is in “VCR” mode, the volume buttons still control your TV’s volume.
1Turn off your VCR.
2Press the MODEbutton and make sure that the VCR LED 
is illuminated.
3Press the SETbutton on your TV’s remote control.
4Using the number buttons on your remote control, enter 
three digits of the VCR code listed on page 26 of this 
manual for your brand of VCR. Make sure you enter three
digits of the code, even if the first digit is a “0”. 
(If more than one code is listed, try the first one.)
5Press the Power button on the remote control. Your VCR
should turn on if your remote is set up correctly. 
If your  VCR does not turn on after set up, repeat steps 
2, 3, and 4, but try one of the other codes listed for your 
brand of VCR. If no other codes are listed, try each VCR
code, 000 through 088.
Setting Up the Remote to Operate Your VCR
BN68-00653A-01Eng.qxd  5/7/04 9:03 AM  Page 23 
						

							English-24
Setting Up the Remote to Operate Your Cable Box
Note on Using Remote Control Modes: Cable Box
When your remote control is in “Cable Box” mode, the volume buttons still control your TV’s volume.
1Turn off your cable box.
2Press the MODEbutton and make sure that the Cable LED is 
illuminated.
3Press the SETbutton on your TV’s remote control.
4Using the number buttons on your remote control, enter three 
digits of the cable box code listed on page 26 of this manual
for your brand of cable box. Make sure you enter three digits 
of the code, even if the first digit is a “0.” 
If there is more than one code listed, try the first one.
5Press the Power button on the remote control. Your cable box 
should turn on if your remote is set up correctly.
If your cable box does not turn on after set up, repeat steps 
2, 3, and 4, but try one of the other codes listed for your brand
of cable box. If no other codes are listed, try each code, 000 
through 077.
BN68-00653A-01Eng.qxd  5/7/04 9:03 AM  Page 24 
						

							English-25
Setting Up the Remote to Operate Your DVD
Note on Using Remote Control Modes: DVD
When your remote control is in “DVD” mode, the volume buttons still control your TV’s volume.
1Turn off your DVD.
2Press the MODEbutton and make sure that the DVD LED is 
illuminated.
3Press the SETbutton on your TV’s remote control.
4Using the number buttons on your remote control, enter three 
digits of the DVD code listed on page 26 of this manual for 
your brand of DVD. Make sure you enter three digits of the 
code, even if the first digit is a “0.” 
If there is more than one code listed, try the first one.
5Press the Power button on the remote control. Your DVD should 
turn on if your remote is set up correctly.
If your DVD does not turn on after set up, repeat steps 2, 3, and
4, but try one of the other codes listed for your brand of DVD.
If no other codes are listed, try each code, 000 through 009.
Setting Up the Remote to Operate Your DVD
BN68-00653A-01Eng.qxd  5/7/04 9:03 AM  Page 25 
						

							English-26
Remote Control Codes
Admiral
Aiwa
Audio Dynamics
Akai
Bell&Howell
Broksonic
Candle
Canon
Citizen
Colortyme
Craig
Curtis-Mathes
Daewoo
DB
Dimensia
Dynatech
Electrohome
Emerson
Fisher
Funai
GE
Go Video
Goldstar
General Electric
Harman Kardon
Hitach
Instant Replay
JC Penny
JCL
JVC015,088
024
022,025
026,031,032
011
019
016,018,022,054,055,061
017,062
016,018,022,054,055,061
023
016,021
009,016,017,023,024,055,062,073,076
003,004,005,006,007,008,022,054,085
025,023
009
024
036
017,018,019,022,024,029,032,036,043,
050,051,056,058,066,071,074,076,077,079
011,021,027,028,052,057,067
024
016
018,023,055,069
009,016,017,041,062
023
014,024,044,045
017
011,014,016,017,023,025,039,044,060,062
011,017,023,025,039,055
015,016
015,016
003
004
005
015,016
020
054
012,013,023,031,032,
033,038,044,075,076,077
011,012,020,021,042,056
045,051,054
012,013,023,031,032,033,038,044,054,070,073
006
009
003
001
007
008
008002
006
004
000
005 045,051
015,016,027,029,034,036,037,040,041,048,049001
017
024,046
024
011,035,047,069
015,016,027,029,034,036,037,040,041,048,049
026,028,052
015,016
008,035,074
011,020,021
010,041
000,011,030,052,071,072007
054
035
054
066
019,067
002
019,067
025,029,057,058,063
039,040,049
059,060
015,016,027,029,034,036,037,040,041,048,049052
022,050,065,069 011,023,025,039,055
082
001,002,007
024
040
024
017,038,062,065
011,017,023,025,038,039,055,070
016,024
016,024,040,041
011,023,025,039,055,070,073
015
017,062,084,086
014,044
055
017,038,062,065
017,038
014,025,042,059
053,054,061
009
011
017,053
011,015,017,018,021,
024,028,036,052,062
kenwood
KLH
LG
Lloyd
Logik
LXI
Magnavox
Marantz
Marta
MEI
Memorex
MGA
Midland
Minota
Mitsubishi
Montgomery ward
MTC
Multitech
NEC
Optimus
Panasonic
Pentax
Pentex Reserch+
Philco
Philips
Pioneer
Portland
ProScan
Quartz
Quasar
Radio Shack/Realistics
Anvision
Cable star
DeaRyung
DongKuk
DaeHan
Eagle
Eastrm Int.
Eastern International
General Instrument
GI
Hamlin
Hitachi
Jerrold
LG
CurtisMathes
JVC
LG
Philips
Proscan
RCAToshiba
Panasonic
Sony
Samsung
Sharp Macom
Magnavox
Nawoo
NSC
Oak
Osk Sigma
Panasonic
Philips
Pioneer
Randtek
RCA
Regal
Regency
SA
SamsungSAEWOO
Signature
Sprucer
Starcom
Stargate 2000
Sylvania
TaePyungYang
Texscan
Tocom
Unika
Universal
Viewstar
Warner Amex
Zenith RCA
Samsung 
Sansui
Sanyo
Scott
Sears
Sharp
Shintom
Signature
Sony
Sylvania
Symphonic
Tandy
Tashiko
Tatung
Teac
Technics
Temika
Teknika
TMK
Toshiba
Toshiko
Totevision
Unitech
Vector Research
Victor
Video Concepts
Videosonic
Wards
Yamaha
Zenith009,014,016,017,037,044,046,063,078
000,016,022,031,041,051
025
011,021
022,050,058,077
011,014,018,021,027,028,044,052,057
015,036,048,054
026,035,040,064
024
026,035,047
017,024,038,062,065
024
011,024
039
024,039,078
018,030
076
014,022,028,057,058
018
016,018
VCR Codes
Cable Box Codes
DVD Codes
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 26 
						

							English-27
Chapter Four
SPECIALFEATURES
Plug & Play Feature
When the TV is initially powered On, two basic customer settings proceed
automatically and subsequently: Setting Auto program, Clock.
1
Press the POWERbutton on the remote control.
The message “Plug & Play”
is displayed.
2
Select the appropriate 
Language by pressing the
UP/DOWNbuttons.
Press the 
ENTERbuttonto confirm your choice.
The message “Antenna Input
Check,” is displayed with
“OK ” selected. 
Press the 
ENTERbutton.
5
Press the MENU()button 
to confirm your setting.
The message “Enjoy your watching.” 
is displayed.
3
Press the UP/DOWNbuttons to select “Air”, “STD”,
HRC”, or “IRC”, then press 
the 
ENTERbutton.
Press the 
ENTERbutton to stop.
4
Press the LEFT/RIGHTbuttons to move to the “Hour”,
“Minute” or “am/pm”. 
Set the hour or minute by
pressing the 
UP/DOWNbuttons.(Refer to “Setting the
Clock” on page 56.)
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 27