Samsung LT-P326W TFL LCD Television User Manual

							English-28
OPERATION
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna)
and cable channels. After the available channels are memorized, use the CH and CH
buttons to scan through the channels. This eliminates the need to change channels by
entering the channel digits. There are three steps for memorizing channels: selecting a
broadcast source, memorizing the channels (automatic) and adding and deleting channels
(manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the
type of signal source that is connected to the TV (i.e., an antenna or a cable system).
1
Press the MENUbutton to
display the menu.
Press the 
UP/DOWNbuttons to select “Channel”,
then press the ENTERbutton.
2
Press the ENTERbutton.
Repeatedly press the 
UP/DOWNbuttons to
cycle through these choices:
“Air”, “STD”, “HRC” or “IRC”
(all cable TV).
Press the 
EXITbutton to exit.
Note : STD, HRC and IRC identify various types of cable TV systems.
Contact your local cable company to identify the type of cable system
that exists in your particular area.
At this point the signal source has been selected.
Proceed to “Storing Channels in Memory” (next page).
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 28 
						

							English-29
OPERATION
3
Press the LEFT/RIGHTbuttons to select “Start”, then
press the ENTERbutton.
The TV will begin  memorizing
all of the available channels.
The TV automatically cycles
through all of the available
channels and stores them in
memory. This takes about
one to two minutes. 
Press 
ENTERat any time
to interrupt the memorization
process and return to the
Channel menu.
2
Press the UP/DOWNbuttons to select
“Auto Program”.
Press the 
ENTERbutton.
1
First, select the correct
signal source
(Air, STD, HRC, IRC).
See steps 1~2 on previous
page.
4
After all the available
channels are stored, the Auto
program menu reappears. 
Press the 
EXITbutton to exit.
Ex) Press  to select channel 108.
Storing Channels in Memory (Automatic Method)
To select channels over 100
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 29 
						

							English-30
OPERATION
Labeling Channels 
1
Press the MENUbutton to display 
the menu.
Press the 
UP/DOWNbuttons 
to select “Channel”, then press 
the 
ENTERbutton. 
Press the 
UP/DOWNbuttons 
to select “Name”, then press the
ENTERbutton.
2
Press the UP/DOWNbuttons 
to select a channel.
You can assign a name to a channel. 
Press the 
LEFT/RIGHTbuttons
to move to  “Labeling” and use 
the 
UP/DOWNbuttons to assign 
a name.
Repeat this procedure to enter up to
four characters.
Press the 
EXIT button to exit.
Alternate method:
Use the number buttons to directly select the channel that will be added or
erased. Press the “ADD/DEL” button. 
Repeatedly pressing 
ENTERwill alternate between “Add”and“Delete”. 
Press the 
EXITbutton to exit.
You can view any channel (including an erased channel) by using the number
buttons on the remote control.
1
Use the number buttons to directly
select the channel to Add or Delete.
Press the 
MENUbutton to
display the menu.
Press the 
UP/DOWNbuttons 
to select “Channel”, then press 
the 
ENTERbutton.
Press the 
UP/DOWNbuttons 
to select “Add/Delete”.
Press the 
ENTERbutton. 
Press the 
ENTERto select
“Add” or “Delete” (pressing
ENTERtoggles between the
two). 
Press the 
EXITbutton to exit.
Adding and Erasing Channels (Manual Method)
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 30 
						

							English-31
1Press the MENUbutton
to display the menu.
Press the UP/DOWNbuttons to select “Channel”,
then press the ENTERbutton. 
Press the UP/DOWNbuttons to select “Favorite
Channel”, then press the
ENTERbutton.
2Press the UP/DOWNbuttons to select your
favorite channels to watch
among the labeledchannels.
Press the 
ENTERbutton
to add a check mark to
set the channel as a favorite
channel.
Press the
EXITbutton when
done to exit.
To Set-up Your Channels
OPERATION
To Select Source
Use to select TV or other external input source connected to the TV.
Use to select the input source of your choice.
1Press the MENUbutton to
display the on-screen menu.
Press the 
ENTERbutton.
2Press the ENTERbutton.
Press the 
UP/DOWNbuttons to select the Input
source, then press the
ENTERbutton.
3
To select the Favorite channels, you have set-up, press the FAV.CH
button on the remote.
If Connector is not connected,
Source cannot be selected except
TV. (in both main and sub-screen)
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 31 
						

							English-32
OPERATION
To Edit the Input Source Name
Name the input device connected to the input jacks to make your input source selection easier.
1
Press the MENUbutton to
display the on-screen menu.
Press the 
ENTERbutton
to select “Input”.
Press the 
UP/DOWNbuttons to select
“Edit Name”, then press
the 
ENTERbutton.
2
Press the UP/DOWNbuttons to select
“AV”, “S-Video”,
“Component1”,
“Component2”, “HDMI”,
“DVI”, or “PC” input jack,
then press the 
ENTERbutton.
3
Press the UP/DOWNbuttons to select “VCR”,
“DVD”,“Cable STB”, 
“HD STB”,“Satellite STB”, 
“AV Receiver”,“DVD
Receiver”, “Game",
“Camcorder”, “DVD Combo”,
“DHR(DVD HDD Recoder)”,
or “PC” input source, then
press the 
ENTERbutton.
Press the 
EXITbutton to
exit.
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 32 
						

							English-33
OPERATION
Using Automatic Picture Settings
Your TV has four automatic picture settings (“Dynamic”, “Standard”, “Movie”, and
“Custom”) that are preset at the factory. You can activate either Dynamic, Standard,
Movie, or Custom by pressing P.MODE (or by making a selection from the menu).
Or, you can select “Custom” which automatically recalls your personalized picture settings.
• Choose Dynamicto increase the clarity and sharpness of the picture.
• Choose 
Standardfor the standard factory settings.
• Choose 
Moviewhen viewing the Movie.
• Choose 
Customif you want to adjust the settings according to personal 
preference (see “Customizing the Picture, page 34).
1
Press the MENUbutton to
display the menu.
Press the 
UP/DOWNbuttons to select “Picture”,
then press the ENTERbutton.
2
Press the ENTERbutton.
Press the 
UP/DOWNbuttons to select the
“Dynamic”, “Standard”,
“Movie”, or “Custom”
picture setting.
Press 
ENTERbutton.
Press the 
EXIT button to exit.
Alternate method:Simply press the P.MODEbutton on the remote control to select
one of the standard picture settings.
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 33 
						

							English-34
OPERATION
Customizing the Picture
You can use the on-screen menus to change the contrast, brightness, sharpness,
color and tint according to personal preference.
(Alternatively, you can use one of the “automatic” settings. See the previous page.)
3
Press the ENTERbutton to select “Contrast”,
“Brightness”, “Sharpness”,
“Color”, or “Tint”.
4
Press the LEFT/RIGHTbuttons to decrease or 
increase the value of a 
particular item. 
For example, if you select
“Contrast”, pressing 
RIGHTincreases it.
Press the 
EXIT button to exit.
2
Press the UP/DOWNbuttons to select“Custom”,then press the ENTERbutton.
1
Press the MENUbutton to
display the menu.
Press the 
UP/DOWNbuttons to select “Picture”,
then press the ENTERbutton.
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 34 
						

							English-35
Using Automatic Sound Settings
Your TV has five automatic sound settings (“Standard”, “Music”, “Movie” “Speech” and
“Custom”) that are preset at the factory. You can select “Custom Sound”, which automatically
recalls your personalized sound settings. 
2
Press the UP/DOWNbuttons repeatedly to select
the “Standard”, “Music”,
“Movie”, “Speech”, or
“Custom” sound settings.
Press the 
EXITbutton
to exit.
1
Press the MENUbutton to
display the menu. 
Press the 
UP/DOWNbuttons to select “Sound”,
then press the ENTER
button.
Press the 
ENTERbutton.
OPERATION
• Choose Standardfor the standard factory settings.
• Choose 
Musicwhen watching music videos or concerts.
• Choose 
Moviewhen watching movies.
• Choose 
Speechwhen watching a show that is mostly dialog (i.e., news).
• Choose 
Customto recall your personalized settings.
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 35 
						

							English-36
OPERATION
2
Press the UP/DOWNbuttons to select
“Custom”, then press the
ENTERbutton.
1
Press the MENUbutton to
display the menu. 
Press the 
UP/DOWNbuttons to select “Sound”,
then press the ENTERbutton.
Customizing the Sound
The sound settings can be adjusted to suit your personal preference.
(Alternatively, you can use one of the “automatic” settings. See the previous page.)
3
Press the LEFT/RIGHTbuttons 
to select a particular item 
to be changed.
Press the 
UP/DOWNbuttons to increase or
decrease the value of a 
particular item.
Press the 
EXITbutton
to exit.
Note :The equalizer allows you to adjust frequencies to your preference.
Note :The lowest frequency is 100 and 10K is the highest.
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 36 
						

							English-37
OPERATION
Selecting a Menu Language
2
Press the UP/DOWNbuttons to select “Language”.
Press the 
ENTERbutton.
1
Press the MENUbutton to
display the menu. 
Press the 
UP/DOWNbuttons to select “Setup”,
then press the ENTERbutton.
3
Press the UP/DOWNbuttons to select “English”,
“Français”, “Español”, or
“Português”.
Press the 
EXITbutton
to exit.
BN68-00653A-01Eng.qxd  5/7/04 9:04 AM  Page 37