Samsung LT-P326W TFL LCD Television User Manual

English-18
INSTALLATION
1. Antenna Cable: Connect the external antenna cable to the ANT IN port on the TV.
2. Anynet Connector: To use the Anynet, connect the Anynet port on the TV and the
Anynet Input port on the DVD Combo using the Stereo-Stereo Anynet connector.
3. AV Connector: If you do not have a Component cable, connect the A/V output jacks on the
DVD/VCR Combo to the AV IN jacks on the TV.
4. Component Cable (Sold Separately): If you have the component connector cable,
connect Component Video Out...

English-19
INSTALLATION
1. Antenna Cable:Connect the external antenna cable to the ANT Input port of the TV.
2. Anynet Connectors:To use the Anynet,connect the Anynet port on the TV and the Anynet Input
port on the DVD Receiver using the Stereo-Stereo Anynet connector.
3. Video Connector:If you do not have the component connector, connect the Video Output port on
the DVD Receiver and the AV IN port on the TV.
4. Audio Connector:Connect the Left-Audio-Right port of Monitor Output on the TV and the Audio...

English-20
INSTALLATION
5. Connecting TV + DVD Combo + DVD Receiver:
Connecting AV Signal Cables
How to Connect the Cables (Connect in the order of numbers shown in the diagram.)
1. Antenna Cable: Connect the external antenna cable to the ANT IN port of the TV. 
2. Anynet Connectors: To use Anynet, connect the Anynet port on the TV and the Anynet Input port
on the DVD/VCR Combo using the Stereo-Stereo Anynet connector.
3. Anynet Connectors: To use Anynet, connect the Anynet Output port on the DVD/VCR...

English-21
Chapter Three
OPERATION
Changing Channels
Using the Channel Buttons
1
Press the CH /buttons to change channels. 
When you press the CH/buttons, the TV changes channels in sequence.
You will see all the channels that the TV has memorized. (The TV must have 
memorized at least three channels). You will not see channels that were either 
erased or not memorized.
Using the PRE-CH Button to select the Previous Channel
1
Press the PRE-CHbutton.The TV will switch to the last channel viewed.
To...

English-22
OPERATION
Viewing the Display
The display identifies the current channel and the status
of certain audio-video settings.  
Viewing the Menus
The on-screen displays
disappear after about ten seconds.
Press the INFO button once more 
or wait approximately 10 seconds 
and it disappears automatically.
Allows the user to adjust the 
settings according to his/her 
preference and shows the 
current settings.1
Press the INFObutton on the
remote control.
The TV will display the
channel, the type of...

English-23
Setting Up Your Remote Control
After it has been set up properly, your remote control can operate in five different modes:
TV, VCR, Cable, DVD or Samsung Set-top box. Pressing the corresponding button on the
remote control allows you to switch between these modes, and control whichever piece of
equipment you choose.
Note
The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.
This remote control is only compatible with Samsung Set-top boxes.
Note on Using Remote...

English-24
Setting Up the Remote to Operate Your Cable Box
Note on Using Remote Control Modes: Cable Box
When your remote control is in “Cable Box” mode, the volume buttons still control your TV’s volume.
1Turn off your cable box.
2Press the MODEbutton and make sure that the Cable LED is 
illuminated.
3Press the SETbutton on your TV’s remote control.
4Using the number buttons on your remote control, enter three 
digits of the cable box code listed on page 26 of this manual
for your brand of cable box....

English-25
Setting Up the Remote to Operate Your DVD
Note on Using Remote Control Modes: DVD
When your remote control is in “DVD” mode, the volume buttons still control your TV’s volume.
1Turn off your DVD.
2Press the MODEbutton and make sure that the DVD LED is 
illuminated.
3Press the SETbutton on your TV’s remote control.
4Using the number buttons on your remote control, enter three 
digits of the DVD code listed on page 26 of this manual for 
your brand of DVD. Make sure you enter three digits of the...

English-26
Remote Control Codes
Admiral
Aiwa
Audio Dynamics
Akai
Bell&Howell
Broksonic
Candle
Canon
Citizen
Colortyme
Craig
Curtis-Mathes
Daewoo
DB
Dimensia
Dynatech
Electrohome
Emerson
Fisher
Funai
GE
Go Video
Goldstar
General Electric
Harman Kardon
Hitach
Instant Replay
JC Penny
JCL
JVC015,088
024
022,025
026,031,032
011
019
016,018,022,054,055,061
017,062
016,018,022,054,055,061
023
016,021
009,016,017,023,024,055,062,073,076
003,004,005,006,007,008,022,054,085
025,023
009
024
036...

English-27
Chapter Four
SPECIALFEATURES
Plug & Play Feature
When the TV is initially powered On, two basic customer settings proceed
automatically and subsequently: Setting Auto program, Clock.
1
Press the POWERbutton on the remote control.
The message “Plug & Play”
is displayed.
2
Select the appropriate 
Language by pressing the
UP/DOWNbuttons.
Press the 
ENTERbuttonto confirm your choice.
The message “Antenna Input
Check,” is displayed with
“OK ” selected. 
Press the 
ENTERbutton.
5
Press the...