Samsung LCD Display SyncMaster 320 MX User Manual

Dimensions
Notice
For  securing 
the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12
mm length.
Wall Bracket Installation • Contact a technician for installing the wall bracket.
• SAMSUNG  Electronics  is  not  responsible  for  any  damages  to  the  product  or  harm  tocustomers when the installation is done by the customer.
• This  product  is  for  installing  on  cement  walls.  The  product  may  not  stay  in  place  when installed on plaster or wood.
Components Only use...

Wall Bracket Assembly
 Note
There are two hinges(left and right). Use the correct one.
1. Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one.
A - Captive Screw
B - Wall Bracket
C - Hinge (Left)
D - Hinge (Right)
2. Before  drilling  into the wall, check if the length between the two locking holes at the back
of the product is correct.
If the length is too short or long, loosen all or...

3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit
to drill 
holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten
the 11 screws A. To mount the product on the wall bracket
The shape 

of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
1. Remove the 4 screws on the back of the product. 2....

3. Tighten 
the  4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product. 4. Remove safety 

pin (3) and insert the 4 product holders into the corresponding bracket
holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to
re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A -
LCD Display
B - Wall Bracket
C - Wall
Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1....

Make sure to use the top center, and not the left or the right side of the product to adjust the
angle.
Introduction 

Connections
Connecting a Computer
Using a Power cord with Earth
•
In the 
event of failure, the earth lead may cause electric shock. Make
sure to wire the earth lead in correctly, before connecting the AC power.
When un-wiring the earth lead, make sure to disconnect the AC power
in advance.  Note
AV  input 

devices such as DVD players, VCRs or camcorders as well as your computer can
be connected to the LCD Display. For detailed information on connecting AV input devices,
refer to the contents under...

Connect the audio cable for your LCD Display to the audio port on the back
of your computer.
 Note
• Turn on both your computer and the LCD Display.
• The DVI
 / D-sub cable is optional.
• Contact a local SAMSUNG Electronics Service Center to buy optional items.
Connecting to Other devices Using a Power cord with Earth
•
In the  event 

of failure, the earth lead may cause electric shock. Make
sure to wire the earth lead in correctly, before connecting the AC power.
When un-wiring the earth lead, make...

Connecting to a Camcorder
1. Locate 
the  AV output jacks on the camcorder. They are usually found on the side or back
of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on
the camcorder and the AV AUDIO IN [L-AUDIO-R] on the LCD Display .
2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display .
3. Select  AV for the Camcorder connection using the Source button on the front of the LCD
Display or on the remote control....

Connecting Using a DVI to HDMI Cable
 Note
• Connect  the 
DVI output terminal of a digital output device to the HDMI terminal of the LCD
Display using a DVI to HDMI cable.
• Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the
DVI / PC / HDMI AUDIO IN terminal of the LCD Display.
Connecting to an Audio System  Note
• Connect a 

set of audio cables between the AUX L, R jacks on the...

 Note
Connect the LAN cable.
(Applicable to the MXn-2 model only)
Connecting a USB device Using a Power cord with Earth
•
In the 
event of failure, the earth lead may cause electric shock. Make
sure to wire the earth lead in correctly, before connecting the AC power.
When un-wiring the earth lead, make sure to disconnect the AC power
in advance.  Note
AV  input 

devices such as DVD players, VCRs or camcorders as well as your computer can
be connected to the LCD Display. For detailed information on...