Samsung Ht As700 User Manual

91
Logical Instructions
Rotation Instructions
MnemonicNameWord ladder 
symbolDouble word 
ladder symbolDescription
WAND 
(DAND)AND (logical 
multiply)Store AND of S1 and S2 in D
WOR
(DOR)OR (logical sum)Store OR of S1 and S2 in D
WXOR 
(DXOR)Exclusive OR 
(exclusive logical 
sum)Store exclusive OR of S1 and S2 in D
WXNR 
(DXNR)Exclusive OR NOT 
(equivalence)Store exclusive OR NOT of S1 and 
S2 in D 1 (ON if they are equal)
MnemonicInstructionWord ladder 
symbolDouble word 
ladder symbolDescription
RLC...

92
Word Conversion Instructions
MnemonicNameWord ladder 
symbolDouble word 
ladder symbolDescription
BCD 
(DBCD)BCD ConversionConvert binary value of S to BCD and 
store it in D.
BIN
(DBIN)Binary ConversionConvert BCD of S to binary number 
and store it in D.
ENCO EncodeStore the location of the highest set 
bit in S in D.
Note) It is different than function of 
SPC series (2
n + 1)
DECO DecodeConvert the low-order 4-bit value of 
S to a power of 2 (2
s) and store it in 
D.
SEG 7-SegmentConverts the...

93
Bit Conversion Instructions
MnemonicNameWord ladder 
symbolDouble word 
ladder symbolDescription
BSET Bit SetSet N
th bit of D to 1.
BRST Bit ResetReset N
th bit of D to 0.
BNOT Bit NotInvert N
th bit of D.
BTST Bit TestStore the value of N
th bit of D to F1.8.
SUM SumStore the number of bits in S that are 
1 to D.
SC Set Carry Set carry bit (F1.8) to 1.
RC Reset Carry
Reset carry bit (F1.8) to 0.
CC Complement Carry
Invert carry bit (F1.8). 
When N=15                      1 (N=0~15)
W h e n  N = 3...

94
Register address data value
absolute address
When N=4
Move Instructions
MnemonicNameWord ladder 
symbolDouble word 
ladder symbolDescription
MOV MoveCopy Ns words from Sr to D.
FMOV Fill MoveRepeatedly copy the value V to the Ns 
words starting from D.
BMOV Bit MoveMove Ns bits from the bit address Sb 
to the bit address Db.
BFMV Bit Fill MoveRepeatedly copy the bit value V to the  
N bits staring from the bit address 
Db. (V=0, 1)(N=1…256)
(Db is bit address)
LDR 
(DLDR)Load   D ← (S)Store to D the...

95
Program Control Instructions
MnemonicNameWord ladder 
symbolDouble word 
ladder symbolDescription
FOR 
(DFOR)For LoopExecute instructions in the block 
between FOR and corresponding 
NEXT. Repeat execution D times.
NEXT NextDecrement D of FOR instruction by 1. 
If it is not zero, repeat execution 
from FOR instruction. 
JMP JumpJump to the position marked LBL L 
(label number).
(L: 0 to 63)
LBL LabelPosition jumped to by the 
corresponding JMP instruction.
(L:0 to 63)
JMPS Jump Start Jump to the JMPE...

96
System Control Instructions
MnemonicNameWord ladder 
symbolDouble word 
ladder symbolDescription
INPR Input RefreshRefresh external input (Receive input 
signal during program execution).
Ch is external input word address.
OUTR Output RefreshRefresh external output (Send 
output signal during program 
execution). 
Ch is external output word address.
WAT Watchdog Timer Clear watchdog scan time.
END ENDEnd of program. This instruction is 
automatically added by WinGPC.
 

97
Communications Control Instructions
MnemonicNameWord ladder 
symbolDouble word 
ladder symbolDescription
READRead Data
(from shared 
memory of high 
performance 
module) Read NR3 words from the module 
memory address NR6 of the slot 
NN5, and write them to the words 
starting from RR1.
WRITEWrite Data
(to shared 
memory of high 
performance 
module)Read NR3 words from NR5, and 
write them to the module memory 
address NR2 of slot NN1.
RMRDRead Remote
Slave Data
(from shared 
memory of high...

98
 

99
7
NX-CPU700p System Product Dimensions
System Dimensions
unit (mm)
Backplane Dimensions 
unit (mm)
 3-slot type5-slot type8-slot type10-slot type12-slot type
A (mm) 205.0 276.0 381.0 452.0 522.0
B (mm) 183.8 254.2 359.8 430.2 500.6
¥ı
5.0*4
L7.0 27.522 .5
A
unit (mm)
 SlotsAL
3 205.0 153.8
5 276.0 224.2
8 381.0 329.8
10 452.0 400.2
12 522.0 470.6
 

100
Power Supply Module Dimensions)
Processor and I/O Modules Dimensions
OPEN
S MSUNG
POWER
Programmable
Controller
104.0 115.5
43.0
SAMSUNG
POWER
Programmable
Controller
OPEN
NX700
unit (mm)
18
19
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
1
2
20
104 .0
115 .5
35.0
INIT
TEST
RUN
RMT
PROG
RS232CTOOL RS232C COMCOM1
RS232C
RS485
COM1
RS232C
RS485
RUN
PROG
TEST
BREAKERROR
BATT
ALARMNX-CPU 700pCPUNX-X 16DDC INNX-X 64DDC IN
unit (mm)