Samsung HP-R6372 Plasma Display User Manual

11
Remote Control Buttons
ŒPOWER button
Turns the TV on and off.
´GUIDE button
Press to display the on-screen Electronic Program Guide (EPG).
ˇANTENNA button
Press to select “Air” or “Cable”.
¨Number buttons
ˆ
-button
Press to select additional channels (digital and analog)
being broadcast by the same station. For example, to select channel
“54-3”, press “54”, then press “
-” and “3”.
ØMUTE button
Press to mute the TV sound.
∏VOL (Volume) buttons
Use it to adjust volume.
”Anynet button
Runs the Anynet...

¿P.MODE buttonAdjust the TV picture by selecting one of the preset factory settings (or
select your personal, customized picture settings). (Refer to page 50)
¸S.MODE buttonSelect Sound effect.
˛E.SAVING buttonPress to adjust screen brightness according to surrounding environment.
(Refer to page 114)
◊P.SIZE buttonSelect Picture size. (Refer to page 54)
±DNIe buttonActivates DNIe Demo. (Refer to page 53)
≠MTS buttonPress to choose stereo, mono or Separate Audio Program 
(SAP broadcast).
–SET buttonUsed...

13
Wall Installation Instructions
Refer to the correct installation guide according to your wall bracket.
1
Contact a technician for installing the wall bracket.
2
Samsung Electronics is not responsible for any damage to the product or injury to yourself
or others if you elect to perform the wall installation.
3
This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood (Ask your dealer).
4
Connect all external devices prior to installing the wall...

14
1 
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
2
Assemble the Support as shown in the
following figure and fasten it with the 
screws after attaching it to the wall. 
(The number of supplied screws  is 
18. For your safety, fasten all 18 
screws).
How to assemble the Wall Mount Bracket
3
After fastening the screws, check if the
support is properly installed as shown in
the figure below.
Captive Screw
Wall Bracket
Hinge (Right)...

15
1 
Remove the 6 screws on the back of the product.
2 
Insert the screw into the plastic hanger. (See the figure below)
Fixing the TV panel to the wall attachment panel bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
3
Tighten the 6 screws in step 2 (plastic
hanger + screw ) to the rear holes of 
the product.
4
Remove safety pin (#) and insert the 4
product holders into the corresponding 
bracket holes (!). Then place...

16
How to Adjust Mounting Angle
Note  Note : Adjust the bracket angle to 0° before installing it on the wall.
Make sure to use the top center,
and not the left or the right side of
the product to adjust the angle.1. Fix the product to the wall bracket.
2. Hold the product at the top in the center and pull it 
forward (direction of the arrow) to adjust the angle. 
(See the figure to the right)
3. You can set the angle of the PDP panel as required by
adjusting the wall support between 0~15°(±2°) for the...

17
How to assemble the Stand-Base
➤ ➤Two or more people should carry the TV. Never lay the TV on the floor because of possible damage to the screen. 
Always store the TV upright.
1
Using the 4 screws for securing the stand pegs and the monitor, firmly attach the monitor
to the stand pegs. (The exterior of the set may be different than the picture.) 
Warning
Firmly secure the stand to
the TV before moving it, 
as the stand may fall and 
could cause serious injury.
BN68-00825N-01Eng_(002~033)  9/28/05...

BN68-00825N-01Eng_(002~033)  9/28/05  9:09 AM  Page 18 

PLASMA DISPLAY PANEL
Connections
Connecting VHF and UHF Antennas ..............................................20
Connecting Cable TV....................................................................21
Connecting a VCR........................................................................23
Connecting a Camcorder ..............................................................24
Connecting a DVD Player (480i, 480p) ..........................................25
Connecting a DTV Receiver (480p, 720p,...

Connecting VHF and UHF Antennas
20
Antennas with 75-ohm Round Leads
If your antenna looks like this: it has 75-ohm round leads.  
1
Plug the antenna lead into the ANT 2 IN (AIR IN) 
on the TV.
Use an antenna cable. (Sold Separately)
BN68-00825N-01Eng_(002~033)  9/28/05  9:09 AM  Page 20