Samsung Hl-t5076s Dlp Tv Owners Instructions

							
English - 21

Setting Up Your Remote Control
After your remote control has been properly set up, your remote control can operate in five different modes: TV, VCR, Cable, 
DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you to switch among these modes, 
and control whichever piece of equipment you choose.
➢ The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes.
Setting Up the Remote to Operate Your VCR
1  Turn off your VCR.2  Press the VCR button on your TV’s remote control.3  Press the SET button on your TV’s remote control.4  Using the number buttons on your remote control, enter three digits of the VCR code listed on page 23 of this manual for your brand of VCR. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)5  Press the POWER button on the remote control. Your VCR should turn on if your remote is 
set up correctly.
If your VCR does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other 
codes listed for your brand of VCR. If no other codes are listed, try each VCR code, 000 
through 080.
Note on Using Remote Control Modes: VCR
When your remote control is in 
VCR mode, the volume buttons still control your TV’s volume.
Continued...
Storing Channels in Memory (Automatic Method)
3  Press the ▲ or ▼ button to select Auto Program, then press the ENTER button.
4  Press the ◄ or ► button to select an antenna connection, then press the ENTER button.
➢ Air: “Air” antenna signal. Cable: “Cable” antenna signal. Air+Cable: “Air” and “Cable” antenna signals.
➢ If the antenna is connected to ANT 1 IN (CABLE), select Cable and if it is connected to 
ANT 2 IN (AIR), select Air.
➢ If both ANT 1 IN (CABLE) and ANT 2 IN (AIR) are connected, select the Air+Cable.➢ If you selected Air, then go to step 6.
5  Press the ◄ or ► to select the correct analog signal source among STD, HRC, and IRC, then press the ENTER button. If you have Digital cable, select the signal source for both Analog and Digital.➢ STD, HRC, and IRC identify various types of cable TV systems.  
Contact your local cable company to identify the type of cable system that exists in 
your particular area. At this point the signal source has been selected.
6  The TV begins memorizing all available stations. When pressing the ENTER button during a storing process, the message  Would you like to stop the auto channel selection? is displayed. Select Yes by pressing the ◄ or ► button.
Press the EXIT button to exit.
➢ The TV must be connected to an antenna/cable in order to receive digital TV signals. 
Even if a particular channel is deleted from the memory, you can always tune to that 
channel directly by using the number buttons on the remote control.
➢ All available DTV and analog channels are automatically stored in memory. It takes approximately 3 to 10 minutes to memorize channels.
Auto Program
Select the antennas to memorize
AirCableAir+Cable
EnterReturn
Auto Program Auto Program in Progress. Cable 3
10%Stop
EnterReturn
Auto Program
Selects the cable system.
AnalogDigitalSTDHRCIRCSTDHRCIRC
EnterReturn
Auto ProgramWould you like to stop the auto channel selection?Cable 310%YesNo
EnterReturn

BP68-00630A-Eng_1.indd   212007-03-30   ｿﾀﾈﾄ 5:14:05 
						

							
English - 22

Setting Up the Remote to Operate Your Cable Box
1  Turn off your cable box.2  Press the CABLE button on your TV’s remote control.3  Press the SET button on your TV’s remote control.4  Using the number buttons on your remote control, enter three digits of the cable box code listed on page 24 of this manual for your brand of cable box. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)5  Press the POWER button on the remote control. 
Your cable box should turn on if your remote is set up correctly.
If your cable box does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the 
other codes listed for your brand of cable box. If no other codes are listed, try each code, 000 
through 046.
Note on Using Remote Control Modes: Cable Box 
When your remote control is in 
CABLE mode, the volume buttons still control your TV’s volume.
Setting Up the Remote to Operate Your DVD
1  Turn off your DVD.2  Press the DVD button on your TV’s remote control.3  Press the SET button on your TV’s remote control.4  Using the number buttons on your remote control, enter three digits of the DVD code listed on page 25 of this manual for your brand of DVD. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)5  Press the POWER button on the remote control. 
Your DVD should turn on if your remote is set up correctly.
If your DVD does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes 
listed for your brand of DVD. If no other codes are listed, try each code, 000 through 141.
Note on Using Remote Control Modes: DVD 
When your remote control is in 
DVD mode, the volume buttons still control your  
TV’s volume.
Setting Up the Remote to Operate Your Set Top Box
1  Turn off your STB.2  Press the STB button on your TV’s remote control.3  Press the SET button on your TV’s remote control.4  Using the number buttons on your remote control, enter three digits of the STB code listed on page 24 of this manual for your brand of STB. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)5  Press the POWER button on the remote control. 
Your STB should turn on if your remote is set up correctly.
If your STB does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other 
codes listed for your brand of STB. If no other codes are listed, try each code, 000 through 074.
Note on Using Remote Control Modes: STB
When your remote control is in 
STB mode, the volume buttons still control your TV’s volume.
Continued...

BP68-00630A-Eng_1.indd   222007-03-30   ｿﾀﾈﾄ 5:14:11 
						

							
English - 23

Remote Control Codes
VCR
BrandSAMSUNGADMIRAL
AIWA
AKAIAUDIO DYNAMICSBELL&HOWELLBROKSONICCANDLECANONCITIZEN
COLORTYME
CRAIG
CURTIS MATHES
DAEWOODBDIMENSIA
DYNATECH
ELECTROHOMEEMERSON
FISHERFUNAI
GENERAL ELECTRIC
GO VIDEOLG(Goldstar)HARMAN KARDON
HITACHI
INSTANT REPLAY
JC PENNEY
JCLKENWOODKLHLIOYDLOGIKLXIJVC
MAGNAVOX
MARANTZ
MARTA
KONIAORIONMEIMEMOREXMGAMIDLAND
MINOLTA
Code000 001 002 003 004 005 077 078 079020025004 027 032007 026018022002 003 006 008 015 055021 056002 003 006 008 015 055007002 024002 007 008 017 021 025 056 064 066
003 010 011 012 013 014 015 016
007 026017025034001 003 006 021 022 025 030 032 034040 047 050 052 060 063 065 066 067 069 073018 024 028 029 048 051 061025002 005 017 021 056002006 007 008 009 010007019 025 041 042 074021002 007 018 019 021 026 037 041054 056007 008 018 021 026 037007 008 018 026 037070025038025081 082 083021 056 059007 008 018 021 026 037 062
006036073 074 075 076021006 021 024 025034005019 041 075
BrandMITSUBISHI
MONTGOMERY WARD
MTC
MULTITECH
NECOPTIMUS
PANASONIC
PENTAX
PENTEX RESEARCH+PHILCOPHILIPSPIONEER
PORTLAND
PROSCAN
QUARTZ
QUASARRADIO SHACK/REALISTICRCA
SANSUISANYOSCOTTSEARSSHARP
SHIMTOM
SIGNATURE
SONY
SYLVANIA
SYMPHONIC
TANDY
TASHIKA
TATUNG
TEACTECHNICSTEKNIKATMK
TOSHIBA
TOTEVISION
UNITECH
VECTOR RESEARCH
VICTOR
VIDEO CONCEPTSVIDEOSONIC
WARDS
YAMAHA
ZENITH
Code019 034 041 046020002 025002 005 025 038007 008 018 026 037 062 064020021 056 071 072019 041 075008021 056 059021 080019 026 039 053015 049 055017018021 056006 018 020 021 024 025 029 034048 056002 017 019 021 035 041 043 057068 076026018 024003 047 052 067006 018 019 024 028 029 041 048 051020 034 045 015027 033 038 058025027 033 044021 025 056 059025018 025006037025 037 068021006 021 025 031066003 019 029 051 052002 006002
007 026026007 026002002 003 006 019 020 021 024 025 034 038 041007 008 018 026 037023 027 033
Continued...

BP68-00630A-Eng_1.indd   232007-03-30   ｿﾀﾈﾄ 5:14:19 
						

							
English - 24

BrandSAMSUNGGIHAMLIN
HITACHI
JERROLDMACOM
MAGNAVOX
OAK
PANASONIC
PHILIPSPIONEERRCAREGAL
Code000 001 002 003 004 005 006 007041003 024 031025 030038 039025 030019 023 028026003 022 027 037 044019 021 023 028004 018 020 044014 022 040003
BrandREGENCYSA
SCIENTIFIC ATLAN
SPRUCER
STARGATE 2000
SYLVANIA
TEXSCAN
TOCOM
UNIVERSAL
VIEWSTAR
WARNER AMEX
ZENITH
Code015 023042 043042 043022036016016032033 034019 021 023 028046017 029 035 037 045
CABLE BOX
ProductGround wave STBSatellite STBCABLE STBSTB DVD COMBOSatellite STB HDD COMBO Standard
Code001 002003004008009
ProductSatellite STB HDD COMBO PremiumCABLE STB HDD COMBO StandardCABLE STB HDD COMBO PremiumGround wave STB HDD COMBO StandardGround wave STB HDD COMBO Premium
Code010
011
012013014
SAMSUNG SET-TOP BOX
Brand
ALPHASTAR
ANAM
CHANNEL MASTER
CROSSDIGITAL
CHAPARRAL
DIRECT TV
DAEWOODISH NETWORK SYSTEMDISHPRODRAKE
DX ANTENNA
ECHOSTAR
EXPRESSVUGOI
GE
GENERAL INSTRUMENT
HTSHOME CABLE
HITACHI
HUGHES NETWORKIQIQ PRISMJANEILJERROIDJVC
Code023043018 034019035015 016 017 019 022 045 060061 062 065 066 067 068074069 070069018 024 032027025 069 070 071069069
065046 047 048 063 064069056022015 017020020059063069 070 
BrandLG(Goldstar)
MAGNAVOX
MEMOREX
MOTOROLA
MACOMMITSUBISHI
NEXT LEVEL
PHILIPS
PRIMESTAR
PANASONIC
PAYSAT
PROSCANRCARADIOSHACK
REALISTICSTS
STAR TRAK
SKY
SKY LIFE
SHACK
STAR CHOICE
SONY
TOSHIBA
ULTIMATE TV
UNIDENZENITH
Code044 073016 021 036 038 039 040 041 042016064018015047 048 064015 016 017 021 033 036 038 039 040 041 042 067046 049 050 063058 059 061 062016065 066051 052 053 065 066064
057020 027026031005 006 007064064054 060015 017 028 029 030 072060 066016 021 037 055 056 057024 031 068
SET-TOP BOX
Continued...

BP68-00630A-Eng_1.indd   242007-03-30   ｿﾀﾈﾄ 5:14:19 
						

							
English - 25

ProductDVDDVDRBD RecordVCR COMBOVCR RecordDHR COMBO
Code000 001 002003 004005 006
007 008 009 010 011
012013
Product
Home Theater VCR COMBO
HDD Record COMBO
TWIN TRAY COMBO
STB DVD COMBODVD Receiver
AV Receiver
Code014 015 016017018019020021
SAMSUNG DVD
BrandANAMAUDIOVOXAUDIOLOGICANABA
APEX DIGITAL
AIWA
BROKSONICBLAUPUNKTB&K
CURTIS MATHES
CYBER HOMECLARIONCIRRUSCINEVISIONDAEWOODENON
FARENHEIT
FISHERGPXGO VIDEOGEGREENHILL
HITACHI
HITEKERHOYOHARMAN / KARDON
IRT
INTEGRAJBLJVC
JATON
KENWOODKISSKONKAKLHLG(Goldstar)LOEWELASONIC
MOBILE AUTHORITY
MEMOREX
MALATA
MAGNAVOX
MINTEKMONYKA
Code030075085072070 071 074 086 083 084 088 
111 112
114
062074122 123027065 077 078 079 082080 125081095066146067 068090060061 089 133 135069 074074
064 113
071073
091 110
089092091
022 033 115 116
073051 108 109073059 100 106 107074 075025 031057058054055056076 093074 094073
BrandNORCENT
NEXT BASE
NEC
NANTAUS
NESA
OPTOMEDIA ELECTRONICS
OPTIVIEWONKYOPHILCO
PRINCETON
PROSCAN
PANASONIC
PHILIPSROTELRIORCARAITE
ROWA
SAMPOSONY
SHERWOOD
SVA
SYLVANIA
SHARPSANSUISANYOSHINSONICSANYOTHOMSON
TOSHIBA
TECHNICSTVIEW
TOKAI
TEACTECHWOODTREDEXURBAN CONCEPTSVENTURERVOCOPRO
YAMAHA
YAMAKAWA
XWAVE
ZENITH
Code048 049 050052053144074105072
076 092 119
044 045046 047023024 034 124 134 136 137 138036 076
117 118
120023 035 074 075 131 132073038104026 029 126 127 128 129 130 141039 041042043 093140062062094090145028 062 076
139072073096097098 099 101076075102032 063040 073103076 121
DVD

BP68-00630A-Eng_1.indd   252007-03-30   ｿﾀﾈﾄ 5:14:20 
						

							
English - 26
To Select the Source
Use to select TV or other external input sources such as DVD players, VCRs, etc. connected to the TV.
1  Press the MENU button. Press the ◄ or ► button to select Input, then press the ENTER button. Press the ▲ or ▼ button to select Source List, then press the ENTER button.
2  Press the ▲ or ▼ button to select a signal source, then press the ENTER button.
➢ You can choose between the following sets of jacks: TV, AV1, AV2, S-Video1, 
S-Video2, Component1, Component2, PC, HDMI1, HDMI2, or HDMI3/DVI on the 
TV’s side panel. 
➢ HDMI1, HDMI2, or HDMI3/DVI input can only be selected when the external device is 
turned on and connected via HDMI.
➢ You can choose only those external devices that are connected to the TV.
Press the SOURCE button on the remote control to view an external signal source.
To Edit the Input Source Name
Name the external device connected to the input jacks to make your input source selection easier.
1  Press the MENU button. Press the ◄ or ► button to select Input, then press the ENTER button. Press the ▲ or ▼ button to select Edit Name, then press the ENTER button.
2  Press the ▲ or ▼ button to select  AV1, AV2, S-Video1, S-Video2, Component1, Component2, PC, HDMI1, HDMI2, or HDMI3/DVI input jack, then press the ENTER button.
3  Press the ▲ or ▼ button to select VCR, DVD, D-VHS, Cable STB, HD STB, Satellite STB, PVR STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DVD HDD Recorder, PC, Internet TV Recv., Interactive TV Recv., VOD STB, or TV input source, then press the ENTER button.
Press the EXIT button to exit.
Input
Enter
Source List
TV AV1
AV2 
S-Video1
S-Video2
Component1Component2PCHDMI1
----
----
----
----
----
----
----
----
Return
Input
Enter
Edit Name
AV1AV2
S-Video1
S-Video2
Component1Component2PCHDMI1HDMI2
---- 
----
----
----
----
----
----
----
----Return
Input
Enter
Edit Name
ReturnAV1
AV2
S-Video1
S-Video2
Component1Component2PCHDMI1HDMI2----
 ----  VCR
  DVD
  D-VHS
  Cable STB
  HD STB
  Satellite STB
  PVR STB
Input
Enter
Input
Source List  ►Edit NameTVReturn
Input
Enter
Input
Source List Edit Name ►TVReturn

BP68-00630A-Eng_1.indd   262007-03-30   ｿﾀﾈﾄ 5:14:22 
						

							
English - 27
Picture Control
Using Automatic Picture Settings
Your TV has three automatic picture settings (“Dynamic”, “Standard”, “Movie”) that are preset at the factory.
You can activate a Picture Setting by making a selection from the menu.
1  Press the MENU button. Press the ENTER button to select Picture. Press the ▲ or ▼ button to select Mode, then press the ENTER button.
2  Press the ▲ or ▼ button to select Dynamic, Standard, or Movie, then press the ENTER button.
  Choose Dynamic to increase the clarity and sharpness of the picture.  Choose Standard for general TV watching mode.  Choose Movie when watching movies.
Press the P.MODE button on the remote control to select one of the standard picture settings.
3  Press the ▲ or ▼ button to select Contrast, Brightness, Sharpness, Color, or Tint, then press the ENTER button.
4  Press the ◄ or ► button to decrease or increase the value of a particular item. Press the ENTER button.
➢ ●  In PC mode, only the Contrast and Brightness can be selected. ●  Each adjusted setting will be stored separately according to its input mode. ●  When you make changes to Contrast, Brightness, Sharpness, Color, or Tint, 
OSD color will also be adjusted accordingly.
Continued...
Picture
Enter
Picture
Mode Contrast 100Brightness   45Sharpness  75Color  55Tint G50  R50Color Tone
Detailed Settings
Size
ReturnDynamic
Cool1
16:9
Picture
Enter
Picture
Mode Contrast 100Brightness   45Sharpness  75Color  55Tint G50  R50Color ToneDetailed SettingsSize
ReturnDynamic
Cool1
16:9
DynamicStandardMovie
Picture
Enter
Picture
Mode Contrast 100Brightness   45Sharpness  75Color  55Tint G50  R50Color Tone
Detailed Settings
Size
ReturnDynamic
Cool1
16:9
▲Contrast▼100
Picture
EnterReturnAdjust

BP68-00630A-Eng_2.indd   272007-03-30   ｿﾀﾈﾄ 5:16:34 
						

							
English - 28

5  Press the ▲ or ▼ button to select Color Tone, then press the ENTER button.
6  Press the ▲ or ▼ button to select Cool2, Cool1, Normal, Warm1, or Warm2, then press the ENTER button.
➢ When the picture mode is set to Dynamic or Standard, Warm1  and Warm2  cannot 
be selected.
Resetting the Picture Settings to the Factory Defaults
7  Press the ▲ or ▼ button to select Reset, then press the ENTER button. Press the ▲ or ▼ button to select OK or Cancel then press the ENTER button.
Press the EXIT button to exit.
➢ Each picture mode can be reset.
Picture
Enter
Picture
Mode Contrast 100Brightness   45Sharpness  75Color  55Tint G50  R50Color ToneDetailed SettingsSize
ReturnDynamic
Cool1
16:9
Picture
Enter
Picture
Mode Contrast 100Brightness   45Sharpness  75Color  55Tint G50  R50Color Tone
Detailed Settings
Size
ReturnDynamic
Cool1OK16:9
Cool2Cool1Normal
Warm1
Warm2
Picture
Enter
PictureTint G50  R50Color Tone
Detailed Settings
Size
Digital NR
DNIe
Active Color
Color Gamut
Position      
Reset
Cool1
16:9Auto On
NormalOn
OKOKCancel

BP68-00630A-Eng_2.indd   282007-03-30   ｿﾀﾈﾄ 5:16:37 
						

							
English - 29

Making Detailed Picture Settings
You can set detailed picture settings.
1  Press the MENU button. Press the ENTER button to select Picture. Press the ▲ or ▼ button to select Detailed Settings, then press the ENTER button.
2  Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
3  When you are satisfied with your setting, press the ENTER button.
Press the EXIT button to exit.
➢ When the picture mode is set to Standard or Movie, Detailed Settings can be selected.
➢ If DNIe is set to Off and the picture mode is in Dynamic or Standard mode, the Detailed Settings cannot be selected.
●  Black Adjust: Off/Low/Medium/High
  You can directly select the black level on the screen to adjust the screen depth.
● Dynamic Contrast: Off/Low/Medium/High
  You can adjust the screen contrast so that the optimal contrast is provided.
● Gamma: -3 ~ +3
  You can adjust the Primary Color Intensity.
  Press the ◄ or ► button until you reach the optimal setting.
●  White Balance:  -10 ~ +10  You can adjust the color temperature for more natural picture colors. Press the ◄ or ► button until you reach the optimal setting.
● My Color Control: Red/Green/Blue/Yellow/Pink/Reset
  This setting can be adjusted to suit your personal preferences.
  Red/Blue/Green/Yellow/Pink: Changing the adjustment value will refresh the adjusted screen. 
  Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. 
  Press the ◄ or ► button until you reach the optimal setting.
 Reset : The previously adjusted colors will be reset to the factory defaults.
● Edge Enhancement: Off/On
  You can emphasize object boundaries.
Picture
Enter
Picture
Mode 
Contrast   80Brightness  50Sharpness  50Color  50Tint G50  R50Color Tone
Detailed Settings  ►
Size
ReturnStandard
Cool1
16:9
Picture
Enter
Return
Detailed Settings
Black Adjust
Dynamic Contrast
Gamma                                        
+1White Balance                                0My Color Control
Edge Enhancement 
MediumMedium
On

BP68-00630A-Eng_2.indd   292007-03-30   ｿﾀﾈﾄ 5:16:38 
						

							
English - 30

Changing the Screen Size
You can select the picture size which best corresponds to your viewing requirements.
1  Press the MENU button. Press the ENTER button to select Picture. Press the ▲ or ▼ button to select Size, then press the ENTER button.
2  Press the ▲ or ▼ button to select the screen format you want, then press the ENTER button.
Press the EXIT button to exit.
 16:9: Sets the picture to 16:9 wide mode. Zoom1: Magnifies the size of the picture on the screen. Zoom2: Expands the Zoom1 format picture. Wide Fit : Enlarges the aspect ratio of the picture to fit the entire screen. 4:3 : Sets the picture to 4:3 normal mode. Just Scan :  Use the function to see the full image without any truncation when DTV(1080i), HDMI (1080i, 1080p) or Component (1080i, 1080p) signals are input.
Press the  P.SIZE button on the remote control to change the picture size.
16:9
Sets the picture to 16:9 wide mode.Zoom1
Magnifies the size of the picture on 
the screen.Zoom2
Expands the Zoom1 format picture.
Wide Fit
Enlarges the aspect ratio of the 
picture to fit the entire screen.4:3
Sets the picture to 4:3 normal mode.Just Scan
Use the function to see the full 
image without any truncation when 
DTV(1080i) , HDMI  (1080i, 1080p)  or Component (1080i, 1080p) signals 
are input.
➢  ●  You can select the 16:9, 4:3, Wide Fit and Just Scan screen sizes in the Component (1080i, 1080p), HDMI (1080i, 1080p),  or DTV (1080i)  mode. ●  In DTV (720p), Component (720p) or HDMI (720p) mode, any of 16:9, 4:3 and Wide Fit can be selected. ●  In Analog TV, AV, S-VIDEO, Component (480i, 480p), HDMI (480i, 480p), or DTV (480i, 480p) mode, any of 16:9, Zoom1, 
Zoom2, and 4:3 can be selected.
 ●  In Zoom1, Zoom2 and Wide Fit modes, you can move the picture on the screen by pressing the ▲ or ▼ button. ●  Each adjusted setting will be stored separately according to its input mode. ●  When watching an HD(High Definition 720p, 1080i, 1080p) signal, you can use Wide Fit. 
Wide Fit sets the optimum picture format by expanding it both horizontally and vertically. For example, you can reset the 
picture in 4:3 format to 16:9. 
Picture
Enter
Picture
Mode Contrast 100Brightness   45Sharpness  75Color  55Tint G50  R50Color Tone
Detailed Settings
Size
ReturnDynamic
Cool1
16:9
Picture
Enter
Picture
Mode Contrast 100Brightness   45Sharpness  75Color  55Tint G50  R50Color Tone
Detailed Settings
Size
ReturnDynamic
Cool1OK16:9
16:9Zoom1Zoom2
Wide Fit 4:3
Just Scan

BP68-00630A-Eng_2.indd   302007-03-30   ｿﾀﾈﾄ 5:16:45