Samsung HL-R5656W Dlp Tv Owners Instructions

							English - 11
Front Panel LED Indicators 
The three lights on the front panel indicate the status of your TV. 
Indicator Light Key
TIMER
Standby state.
The picture will automatically appear in about 15 seconds.
Auto Timer ON/OFF has been set and the set will automatically be
turned on in about 25 seconds.
A cooling fan inside the set is not operating normally.
Lamp cover on the rear of the set is not properly shut. 
Check if the ventilation hole on the rear of the set is blocked, because
if the inner temperature is too high, the power will shut off. 
Lamp may be defective. Please contact a certified technician.LAMPSTAND BY/TEMP Indication
: Light is On
: Light is Blinking
: Light is Off
Remote Control Sensor  
Aim the remote control towards this spot on the TV.
POWER
Press to turn the TV on and off.
•  It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.
•  The TV has a fan to keep the inside lamp from overheating. You’ll occasionally hear it working.
BP68-00524A-00(002~015)  6/3/05  3:11 PM  Page 11 
						

							Rear Panel Jacks
Use the rear panel jacks to connect components such as a VCR. You can connect different components
such as VCRs, Set-Top Box and a DVD player etc., because there are two sets of video input jacks and
two sets of component video input jacks on the rear panel of your TV. For more information, see
“Connections”.
Your New Wide TV
English - 12
ŒANTENNA terminalsTwo independent cables or antennas can be connected to 
these terminals. Use “ANT 1 IN (CABLE)” and “ANT 2 IN (AIR)”
terminals to receive a signal from VHF/UHF antennas or your
cable system. (Refer to pages 16~18)
´
SERVICEThis jack is for software upgrades.
ˇ
S-VIDEO INPUT jacksConnects an S-Video signal from an S-VHS VCR or DVD player. 
(Refer to page 20)
¨
DVI (Digital Video Interface) AUDIO INPUT jacksConnect to the digital audio output jacks of a device with DVI 
output. (Refer to page 22)
ˆ
VIDEO/AUDIO INPUT jacks Connect video/audio signals from external sources, such as VCR
or DVD players. (Refer to page 21)
Ø
VIDEO/AUDIO OUTPUT jacks  Sends video/audio signals from the TV to an external source,
such as a VCR. These jacks are available only in RF, Video and 
S-Video modes. ∏
COMPONENT1, 2 jacks (Y, PB, PR, AUDIO L/R) Use these jacks to connect the component video/audio signals
from a DVD player or a Set-Top Box. (Refer to pages 21~22)
”
DIGITAL AUDIO OUT (OPTICAL) jackConnect to a Digital Audio Component. (Refer to page 24)
’
Anynet Please refer to the Anynet Owner’s Instruction. This jack is for 
connecting to other Samsung Anynet-enabled devices.
˝
HDMI (High Definition Multimedia Interface)/ 
DVI INPUT jack
Connect to the HDMI jack of a device with HDMI output. 
These inputs can also be used as a DVI connection with separate
analog audio inputs. An optional HDMI/DVI cable will be 
necessary to make this connection. When using the optional
HDMI/DVI adapter, the DVI analog audio inputs on your TV 
allow you to receive left and right audio from your DVI device.
(Refer to pages 22~23)
BP68-00524A-00(002~015)  6/3/05  3:11 PM  Page 12 
						

							English - 13
Remote Control
You can use your remote control within a distance of 23 feet and an angle of 30 degrees from the left
and right sides of the TV’s remote control receiver. You can also use your remote control to operate your
VCR, Cable box, DVD player or some Samsung Set-top boxes. See pages 32~33 for details. 
1. POWERTurns the TV on and off.
2. P.MODEAdjust the TV picture by selecting one of 
the preset factory settings (or select your
personal, customized picture settings.)
3. ANTENNAPress to select “AIR” or “CABLE”.
4. CHANNEL NUMBER Press to directly tune to a particular channel.
5.-Press to select additional channels (digital
and analog) being broadcast by the same
station. For example, to select channel 
“54-3”, press “54”, then press “
-” and “3”.
6. VOL +, VOL -Press to increase or decrease the volume.
7. MUTEPress to mute the TV sound.
8. AnynetRuns the Anynet view functions and sets up
Anynet devices. Please refer to the Anynet
Owner’s Instruction.
9. MENUDisplays the main on-screen menu.
10. CH.LISTDisplays the channel list.
11. FAV.CH (Favorite Channel)Press to switch between your favorite 
channels.
12. MODESelects a target device to be controlled by
the Samsung remote control (i.e., TV, STB,
VCR, CABLE, or DVD).
13. PRE-CHTunes to the previous channel.
14. SOURCEPress to display all of the available video
sources (i.e., TV, Set-Top Box, VCR, DVD,
DTV).
15. CH /Press to change channels. 
Moves from one set of screen information to
the next in TV Guide menu.
16. INFOPress to display information on the TV
screen.
17. EXITPress to exit the menu.
18.▲, ▼, œ, √, ENTERPress to select highlight up, down, left, or
right. While using the on-screen menus,
press ENTER to activate (or change) a 
particular item.
19. MTS (Multichannel Television
Stereo)
Press to choose Stereo, Mono or SAP
(Secondary Audio Program).
20. STILLPress to pause the current screen.
21. P.SIZEPress to change the screen size.
22. DNSeDNSe enhances the sound quality,
automatically controls output,
and prevents sound distortion.
Press this button to set it On or Off.
23. DNIe (Digital Natural Image
engine)
Activates DNIe Demo mode.
24. SETUsed during set up of this remote control, 
so that it will work compatibly with other
devices (some Samsung Set-top boxes, VCR,
Cable box, DVD, etc.)
25. SLEEPPress to select a preset time interval for
automatic shut off.
26. CAPTIONControls the caption decoder.
27. VCR/DVD ControlsControls VCR or DVD functions: Rewind, Stop,
Play/Pause, Fast Forward.
28. RESETIf your remote control is not functioning
properly, take out the batteries and press
the reset button for about 2~3 seconds. 
Re-insert the batteries and try using the
remote control again. 
The blue button is only
used during the channel
list as an EXIT button.
BP68-00524A-00(002~015)  6/7/05  10:23 AM  Page 13 
						

							Installing Batteries in the Remote Control
With normal use, the batteries in the remote control should last about a year. If you notice a performance
degradation while using the remote, the batteries may need to be replaced. Make sure you replace both
batteries and do not mix old and new batteries in the remote control. If you won’t be using the remote
control for a long time, remove the batteries and store them in a cool dry place.
1
Slide the back cover all the way out to open
the battery compartment of the remote control.
2
Install two AAA size batteries. Make sure to 
match the “+” and “–” ends of the batteries 
with the diagram inside the compartment.
3
Slide the cover back into place.
NOTE
•Do not mix battery types, i.e, alkaline and manganese.
Your New Wide TV
English - 14
BP68-00524A-00(002~015)  6/3/05  3:11 PM  Page 14 
						

							Connections
BP68-00524A-00(002~015)  6/3/05  3:11 PM  Page 15 
						

							Connections
English - 16
Connecting VHF and UHF Antennas
If you do not have a cable system, you will need to connect an antenna to your TV.  
Antennas with 75-ohm Round Leads
If your antenna looks like this: it has 75-ohm round leads.
1
Plug the antenna lead into
the ANT 2 IN (AIR) on the 
rear panel of your TV.
BP68-00524A-00(016~025)  6/3/05  3:17 PM  Page 16 
						

							English - 17
Connecting Cable TV
You can connect different cable systems to your TV, including cable without a Cable box, 
and cable with a Cable box that descrambles some or all channels.
Cable without a Cable Box
1
Plug the incoming cable into
the ANT 1 IN (CABLE) on the
rear panel of your TV.
Cable with a Cable Box that Descrambles All Channels
1
Find the cable connected to
the ANTENNA OUT 
terminal on your Cable box. 
This terminal might be 
labeled “ANT OUT”, “VHF 
OUT” or simply “OUT”.
2
Connect the other end of 
the cable to the “ANT 1 IN
(CABLE)” terminal on the 
rear panel of your TV.
BP68-00524A-00(016~025)  6/3/05  3:17 PM  Page 17 
						

							Connections
English - 18
Cable with a Cable Box that Descrambles Some (But Not All) Channels
To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial
cables (which you can buy from your Samsung dealer or any electronics store).
1
Find and disconnect the
cable that is connected to 
the ANTENNA IN terminal 
of your Splitter. 
This terminal might be 
labeled “ANT IN”, “VHF IN”
or simply, “IN”. Connect this 
cable to a two-way splitter.
2
Connect a coaxial cable
between an OUT terminal 
of the splitter and the IN 
terminal of the Cable box.
3
Connect a coaxial cable
between the ANTENNA OUT
terminal of the Cable box
and the B-IN terminal of the
RF (A/B) switch.
4
Connect a coaxial cable
between the other OUT 
terminal of the Cable box 
and the A-IN terminal of the
RF (A/B) switch.
5
Connect the last coaxial
cable between the OUT 
terminal of the RF (A/B) 
switch and the ANT 1 IN
(CABLE) on the TV.
After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. 
Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch 
to “B”, you will need to tune your Set-Top Box to the Cable boxs output channel, which is usually
channel 3 or 4.)
BP68-00524A-00(016~025)  6/3/05  3:17 PM  Page 18 
						

							English - 19
Connecting a VCR
Connecting a VCR to the Video or S-Video/Audio jack
1
Connect the Video/Audio
cables between the VIDEO 
or S-VIDEO/AUDIO input 
jacks on the TV and VIDEO 
or S-VIDEO/AUDIO output 
jacks on the VCR.
NOTES
•For better video, use an 
S-Video cable.
•Please be sure to match the
color coded input terminals
and cable jacks.
TV Rear Panel
Incoming
Cable or 
Antenna
Stereo VCR
or
BP68-00524A-00(016~025)  6/3/05  3:17 PM  Page 19 
						

							Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a Camcorder to your TV.
You can use your camcorder to view tapes without using a VCR.
1
Locate the A/V output jacks
on the camcorder. They are
usually found on the side or
back of the camcorder. 
2
Connect a set of audio
cables between the AUDIO
IN jacks on the TV and the
AUDIO OUT jacks on the
camcorder. If you have a
mono Camcorder, connect
L(mono) to the Camcorder
audio out using only one
audio cable.
3
Connect a video cable
between the VIDEO IN (or 
S-VIDEO IN) jack on the TV
and the VIDEO OUT jack 
on the Camcorder. The
audio-video cables shown
here are usually included
with a Camcorder. (If not,
check your local electronics
store.) If your Camcorder is
stereo, you need to connect
a set of two cables.
Connections
English - 20
Camcorder 
Output Jacks
1
TV Rear of right side
orCamcorder
2
3
BP68-00524A-00(016~025)  6/3/05  3:17 PM  Page 20