Samsung Dcs 400si General Description Manual

							CONTENTS
5.2
c. Ringer Equivalence Number 0.5 B for D8UTK and D16TK
d. Interface Jack type RJ21X
The 400si may be configured as a key system or a hybrid system. Depending on the
method of operation, the appropriate FCC number must be given to the telephone com-
pany. Certain features such as pooled access by button or dial access, LCR, off premise
extensions and tie lines may require the hybrid registration. Check with the local tele-
phone company providing the service if you are in doubt. It is the customer’s responsibility
to comply with local telephone company tariffs.
TELEPHONE CONNECTION REQUIREMENTS
The Federal Communications Commission (FCC) has established rules which permit the
400si to be connected directly to the telephone network using telephone company net-
work access jacks usually referred to as “Registered Jacks.”
5.3 TELEPHONE COMPANY INTERFACES
CIRCUIT TYPE DCS 400SI FACILITY           NETWORK
CARD TYPE INTERFACE CODE    JACK
LOOP START LINE D8UTK O2LS2 RJ21X
D16TK O2LS2 RJ21C
RJ14C
RJ11C
DTPRI 04DU9-BN RJ48C
GROUND START DTPRI 04DU9-BN RJ48C
LINE D8UTK 02GS2 RJ21X
RJ11C
RJ14C
DID LINE T1 04DU9-BN RJ48C
D8UTK 02RV2-T RJ21X
RJ11C
RJ14C
E & M TIE LINE T1 04DU9-BN RJ48C
D8UTK TL11M RJ2EX
ISDN D8BRI 02IS5 RJ48C
DTPRI 04DU9-C RJ48C
OFF PREMISES D16SLI circuit OL13C RJ21X
EXTENSION board only RJ11C
RJ14C 
						

							CONTENTS
5.3
NOTE: See Special Application section for information about ordering ISDN services.
RINGER EQUIVALENCE (REN)
The REN is used to determine the quantity of devices which may be connected to the
telephone line. Excessive RENs on the telephone line may result in the devices not ringing
in response to an incoming call. In most but not all areas, the sum of the RENs should not
exceed 5.0. To be certain of the number of devices that may be connected to the line, as
determined by the number of RENs, contact the telephone company to determine the
maximum REN for the calling area.
INCIDENCE OF HARM
If the terminal equipment, the DCS 400si, causes harm to the telephone network, the
telephone company will notify you in advance that temporary discontinuance of service
may be required. But if advance notice is not practical, the telephone company will notify
the customer as soon as possible. Also, you will be advised of your right to file a complaint
with the FCC if you believe it is necessary.
CHANGES TO TELEPHONE COMPANY EQUIPMENT OR FACILITIES
The telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens, the telephone
company will provide advance notice in order for you to make the necessary modifications
so that you may maintain uninterrupted service.
SERVICE CENTER
If trouble is experienced with the DCS 400si, please contact your SAMSUNG
TELECOMMUNICATIONS AMERICA at (305) 592-2900 for repair or warranty information.
If the trouble is causing harm to the telephone network, the telephone company may
request that you remove the equipment from the network until the problem is resolved.
FIELD REPAIRS
Only technicians certified on the DCS 400si are authorized by SAMSUNG
TELECOMMUNICATIONS AMERICA to perform system repairs. Certified technicians may
replace modular parts of a system to repair or diagnose trouble. Defective modular parts
can be returned to SAMSUNG TELECOMMUNICATIONS AMERICA for repair.
GENERAL
This equipment must not be used on coin telephone lines. Connection to party line service
is subject to state tariffs.
The DCS 400si system uses toll restriction and LCR features that are programmed to
allow dialing over the public telephone network. The North American Numbering Plan
(NANP) determines these network area codes and exchange codes. Failure to update the
system programming or software may deny you access to new area codes and exchanges.
Bell Communication Research (Bellcore) administers the NANP and publishes it. To ob-
tain the latest information and keep your system current, contact Bellcore at (201) 829-
3071. 
						

							CONTENTS
5.4
HEARING AID COMPATIBILITY
All models of the keysets are hearing aid compatible as specified in Par\
t 68 of the FCC 
Rules.
5.4 UNDERWRITERS LABORATORIES
The 400si system has been tested to comply with safety standards in the \
United States as
listed below. This system is listed with Underwriters Laboratories. 
LISTED         US
UL  83X3 
E118093
Project No.: 98NK12211
5.5 MUSIC ON HOLD WARNING
IMPORTANT NOTICE : In accordance with US copyright laws, a license may be required
from the American Society of Composers, Authors and Publishers (ASCAP)\
 or other simi-
lar organizations if copyrighted music is transmitted through the Music \
on Hold feature.
SAMSUNG TELECOMMUNICATIONS AMERICA hereby disclaims any liability arising
out of failure to obtain such a license.
5.6 EQUAL ACCESS REQUIREMENTS
The 400si is capable of providing users access to interstate providers o\
f operator services
through the use of access codes.  Modifications of this equipment by cal\
l aggregators to
block access dialing codes is a violation of the Telephone Operator Consumer Act of 1990
and Part 68 of the FCC Rules.
5.7 DISA WARNING
Lines that are used for the Direct Inward System Access feature must hav\
e the disconnect
supervision options provided by the telephone company. 
WARNING: As it is impossible to control who may access your DISA line it \
is suggested 
that you do not turn this feature on unless you intend to use it.  If yo\
u do use this feature,
it is good practice to frequently change passcodes and periodically revi\
ew your telephone
records for unauthorized use.