Samsung CLP 550 User Manual

							USING PRINT MATERIALS3.5
3
3Flex the paper sheets back and forth to separate the pages, 
and then fan them while holding one edge. Tap the edge of 
the stack on a flat surface to even it up.
4Load paper with the print side facing up.
Make sure that all four corners are flat in the tray and under 
the corner brackets, as shown below.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.6
5Do not exceed the maximum stack height. Overfilling the 
tray may cause a paper jam.
6Pinch the paper guide, as shown and move it towards the 
paper until it lightly touches the side of the stack. Do not 
press the guide too tightly against the edge of the paper as 
the guide may bend the paper. 
NOTE: If you want to change the paper size in the tray, refer to 
page 3.7.
7Slide the tray back into the printer.
8When you print a document, select the paper type, size and 
source in your software application. For details, see 
page 4.7.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.7
3
Changing the Paper Size in the Tray
The tray is preset to Letter or A4 size, depending on your 
country. To change the size to A4 or Letter, you must adjust the 
paper length guide properly.
1Lift the paper length guide and place it in the correct 
position for the paper size you are loading.
To remove the paper length guide, turn it slightly to your 
right to release the locks on the bottom of the guide, then 
pull it up. 
To place the paper length guide in the paper position you 
want, insert the locks on the bottom of the guide into the 
desired paper slot and push it all the way in. 
Paper length guide
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.8
2Load paper with the print side facing up. For more 
information, see steps 4 and 5 on page 3.5~3.6.
3Pinch the paper guide, as shown and move it towards the 
paper until it lightly touches the side of the stack. Do not 
push the guide to tightly against the edge of the paper as it 
may cause the paper to bend. 
Using the Optional Tray 2 
The optional tray, Tray 2, can hold a maximum of 500 sheets of 
plain paper.
To load paper in Tray 2, follow the instructions for loading paper 
on page 3.4.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.9
3
Using the Multi-purpose Tray
The Multi-purpose Tray is located on the right side of your 
printer. It can be closed when you are not using it, making the 
printer more compact. 
The Multi-purpose Tray can hold several sizes and types of 
material, such as transparencies, cards and envelopes. You may 
also want to use the Multi-purpose Tray for single page print jobs 
on letterhead, colored paper for use as separator sheets, or 
other special materials that you do not normally keep in the 
paper tray. You can load approximately 100 sheets of plain 
paper, 10 envelopes, 30 transparencies, 10 sheets of card stock 
or 10 labels at a time. 
• Load only one size of print material at a time in the 
Multi-purpose Tray.
• To prevent paper jams, do not add paper when there is still 
paper in the Multi-purpose Tray. This also applies to other 
types of print materials.
• Print materials should be loaded face down with the top edge 
going into the Multi-purpose Tray first and be placed in the 
center of the tray.
To load print material in the Multi-purpose Tray:
1Lower the Multi-purpose Tray and unfold the paper support 
extension, as shown. 
Multi-purpose Tray
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.10
2If you are using paper, flex or fan the edge of the paper 
stack to separate the pages before loading.
For transparencies, hold them by the edges and avoid 
touching the print side. Oils from your fingers can cause 
print quality problems. 
3Load the print material with the print side facing down 
and against the right edge of the tray.
4Pinch the paper width guide and slide it to the right to touch 
lightly against the edge of the material without bending it.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.11
3
If you want to print on previously printed paper from the 
Multi-purpose Tray, the printed side should be facing up 
with the uncurled edge towards the printer. If you 
experience problems with the paper feeding, turn the paper 
around.
NOTE: Make sure that you have 
not loaded too much print 
material. 
The print material buckles if you 
load a stack that is too deep or if 
you push it in too far.
5When you print a document, set the paper source to MP 
Tray and select the correct paper type in the software 
application. For details, see page 4.7.
NOTE: After printing fold away the 
paper support extension and close 
the Multi-purpose Tray. 
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.12
Using the Manual Feed 
If you select Manual in the Source option when changing print 
settings, you can manually load a sheet of print material in the 
Multi-purpose Tray. Manually loading paper can be helpful when 
you want to check the print quality after each page is printed. 
This loading procedure is almost the same as the procedure for 
loading in the Multi-purpose Tray, except you load paper 
sheet-by-sheet in the Tray, send print data to print the first 
page, and press the On Line/Continue button ( ) on the 
control panel to print each following page.
1Load a sheet of print material with the print side down 
and against the right edge of the Multi-purpose Tray. 
2Pinch the paper width guide and slide it to the right to touch 
lightly against the edge of the paper without bending it.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.13
3
3When you print a document, you must select Manual for 
Source in the software application, and then select the 
correct paper size and type. For details, see page 4.7. 
4Print the document. 
The display shows a message prompting you to load paper. 
5Press the On Line/Continue button ( ). 
The printer picks up the print material and prints. After one 
page is printed, the message appears again.
6Insert the next sheet into the Multi-purpose Tray and press 
the On Line/Continue button ( ).
Repeat this step for every page to be printed.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.14
Printing on Special Print Materials
Printing on Envelopes
• Load envelopes into the Multi-purpose Tray only.
• Only use envelopes recommended for laser printers. Before 
loading envelopes in the Multi-purpose Tray, make sure that 
they are undamaged and are not stuck together. 
• Do not feed stamped envelopes.
• Never use envelopes with clasps, snaps, windows, coated 
linings, or self-stick adhesives. 
To print on envelopes:
1Open the Multi-purpose Tray and unfold the paper support.
2Flex or fan the edge of the envelope stack to separate them 
before loading.
3Load the envelopes into the Multi-purpose Tray with the 
flap side up. The end of the envelope with the stamp area 
enters the printer first. 
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls