Samsung CLP 550 User Manual

							USING PRINT MATERIALS3.15
3
4Pinch the paper width guide and slide it to the right to touch 
lightly against the edge of the stack without bending it.
5When you print, configure the paper source to MP Tray, the 
paper type to Envelope and the paper size in the software 
application. For details, see page 4.7. 
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.16
Printing on Labels
• Only use labels recommended for laser printers.
• Verify that the labels’ adhesive material can tolerate a fusing 
temperature of 180°C (356°F) for 0.1 seconds.
• Make sure that there is no exposed adhesive material 
between the labels. Exposed areas can cause labels to peel 
off during printing, which can cause paper jams. Exposed 
adhesives can also cause damage to the printer components.
• Never print on the same sheet of labels more than once or on 
partial sheet of labels.
• Do not use labels that are separating from the backing sheet 
or are wrinkled or damaged in any way.
• To prevent labels from sticking together, do not let the printed 
label sheets stack up as they are printed out. 
To print on labels:
1Open the Multi-purpose Tray and unfold the paper support.
2Load labels only in the Multi-purpose Tray with the print 
side down and the top, short edge in first. Adjust the guide 
to fit the width of the labels. 
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.17
3
3When you print, configure the paper source to MP Tray, the 
paper type to Labels and the size in the software 
application. For details, see page 4.7. 
Printing on Transparencies
• When you print a color document do not use transparencies 
with an attached backing sheet. This may cause print quality 
problems.
• Only use transparencies recommended for use in laser 
printers.
• Ensure that transparencies do not have torn edges and are 
not wrinkled or curled.
• Hold the transparencies by the edges and avoid touching the 
print side. Oils from your fingers can cause print quality 
problems.
• Be careful not to leave fingerprints on the print side and/or 
scratch marks.
• The following paper types are recommended:
A4: 003R96002, Letter: 3R3108
NOTE: Before printing on 
transparencies, make sure that 
the output support is laid down.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.18
To print on transparencies:
1Open the Multi-purpose Tray and unfold the paper support.
2Load transparencies into the Multi-purpose Tray. They must 
be loaded with the print side downwards and the top 
with the white leading edge entering the printer first. 
Adjust the guide to fit the width of the transparencies. 
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.19
\f
3When you ‘frint, configure the ‘f‘b‘fer source to  MP Tray, the 
‘f‘b‘fer ty‘fe to  Transparency , ‘bnd the ‘f‘b‘fer size in the 
softw‘bre ‘b‘f‘flic‘btion. For det‘bils, see ‘f‘bge 4.7. 
NOTES: 
• To prevent transparencies from sti\Lcking together, do not let the  printed sheets stack u\Lp as they are print\Led out.
• Place transparencies on a fla\Lt surface after remo\Lving them from  the printer.
• Prints made on transparency film with \Lthis printer are no\Lt  compatible with overhead projectors and \Lmay appear as a black \L
and white image if pr\Lojected.
DownloadedsFromsManualsPrinterbcomsManuals 
						

							USING PRINT MATERIALS3.20
Printing on Preprinted Paper
• Preprinted paper is paper that has some type of printing 
placed on it before it is sent through the printer (paper that 
has a preprinted logo at the top of the page, for example).
• Letterhead must be printed with heat-resistant ink that will 
not melt, vaporize, or release hazardous emissions when 
subjected to the printer’s fusing temperature of 180°C 
(356°F) for 0.1 seconds.
• Ink on letterhead must be non-flammable and should not 
adversely affect any printer rollers.
• Forms and letterhead should be sealed in moisture-proof 
wrapping to prevent changes during storage.
• Before you load preprinted paper, such as forms and 
letterhead, verify that the ink on the paper is dry. During the 
fusing process, wet ink can come off of preprinted paper, 
reducing the print quality.
To print on preprinted paper:
1Open the Multi-purpose Tray and unfold the paper support.
2Load letterhead only in the Multi-purpose Tray with the 
print side down and the top, short edge, in first. 
Adjust the guide to fit the width of the paper stack.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.21
3
3When you print, configure the paper source to MP Tray, the 
paper type to Preprinted, and the paper size in the 
software application. For details, see page 4.7. 
Printing on Card Stock or Custom-sized 
Materials
• Postcards, 3.5 in. by 5.5 in. (index) cards and other custom-
sized materials can be printed with your printer. The 
minimum size is 90 mm by 140 mm (3.5 in. by 5.5 in.) and 
the maximum size is 216 mm by 356 mm (8.5 in. by 14 in.).
• Always insert the short edge into the Multi-purpose Tray first. 
If you want to print in landscape mode, make this selection 
using your software. Inserting the long edge first may cause 
a paper jam.
• Do not load more than 10 cards into the Multi-purpose Tray at 
a time.
• Do not print on material smaller than 90 mm (3.5 in.) wide or 
140 mm (5.5 in.) long.
• Set margins of at least 4.3 mm away from the edges of the 
material in the software application.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.22
To print on card stock:
1Open the Multi-purpose Tray and unfold the paper support.
2Load print material only in the Multi-purpose Tray with the 
print side down and the short edge first. Slide the guide 
until it lightly touches the stack without bending it.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.23
3
3When you print, configure the paper source to MP Tray, the 
paper type and size in the software application. For details, 
see page 4.7. 
If the size of your print material is not listed in the Size box 
in the Paper tab, click the 
Custom button and set the size 
manually. See page 4.7.
qownlo#ded2(rom2Q#nu#lsKrinterIcom2Q#nu#ls 
						

							USING PRINT MATERIALS3.24
MEMO
Downloaded From ManualsPrinter.com Manuals