Samsung CLP 550 User Manual

							SETUP GUIDE9
English
6Hold the handle on the imaging unit with the green roller 
facing you. Align the imaging unit with the slots in your 
printer so that the colors on both sides of the imaging unit 
slide into the corresponding colors of the slots.
CAUTION: Insert the imaging unit carefully so as not to scratch 
and damage the surface of the green roller.
7Slide the imaging unit down into the printer until it cannot 
be pushed in any further and fold the handle down. 
CAUTION: To prevent damage, do not expose the imaging unit to 
light for more than a few minutes. Close the top and left cover 
should the setup need to be halted for any reason.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: Keep the transfer belt level, do not turn the transfer belt 
over otherwise looses toner may be spilled.
13Slide the transfer belt down into the printer. Press it firmly 
to make sure that it latches into place.
%ownloadedd/romd“anuals@rinterbcomd“anuals
CAUTION: Do not use sharp objects, such as a knife or scissors, 
to open the toner cartridges packages. You could damage the 
surface of the toner cartridges.
17Holding both sides of the cartridges, gently roll them from 
side to side to distribute the toner.
18Place the toner cartridges on a flat surface as shown and 
remove the paper covering on the toner cartridge by 
removing the tape.
NOTE: If toner gets on your clothing, wipe it off with a dry cloth 
and wash it in cold water. Hot water sets toner into fabric.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: When printing text at 5% coverage, you can expect a 
toner cartridge life of about 7,000 pages for black and 5,000 pages 
for color. 
%ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
TEUP: Connecting the printer to the USB port of the computer 
requires a certified USB cable. You will need to buy a USB 2.0 
compliant cable that is within 3m in length. 
1Make sure that both the printer and the computer are 
turned off.
2Plug the USB printer cable into the connector on the back of 
the printer. 
3Connect the other end of the cable to the USB port on your 
computer. 
See the User’s Guide of your computer, if you need help.
NOTE: To print using the USB interface, you must run Windows 
98/Me/2000/XP, or Macintosh with OS 8.6~9.2/10.1~10.3.
To the USB port on 
your computer
%ownloadedd/romd“anuals@rinterbcomd“anuals
To the network 
LAN connection
%ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: For Windows NT 4.0/2000/XP, the system administrator 
should install the software. 
All applications should be closed on your PC before beginning 
installation. 
1Place the CD-ROM in the CD-ROM drive. Installation will 
start automatically.
If the CD-ROM drive does not automatically run:
Select Run from the Start menu, and type x:\Setup.exe 
in the Open box (where x is the drive letter for the CD-ROM 
drive), then click OK.
NOTE: If the New Hardware Found window appears during the 
installation procedure, click   in the upper right corner of the box, 
or click Cancel. 
ItemRequirements
Operating systemWindows 95/98/Me/NT 4.0/2000/XP
RAM95/98/Me 32 MB
NT 4.0/2000 64 MB
XP 128 MB
Free disk space95/98/Me/NT 4.0/
2000/XP300 MB
Internet Explorer 5.0 or higher

Downloaded From ManualsPrinter.com ManualsDownloaded From ManualsPrinter.com Manuals
NOTE: If your printer is not connected to the computer, the 
Connect Samsung CLP-550 Series window opens. After connecting 
the printer, click Next.
4Select the components you want to reinstall and click Next.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: If your computer doesn’t have Adobe Acrobat, selecting 
the View User’s Guide option automatically installs Adobe 
Acrobat for you. After installing is complete, repeats step 1 and 2. 
In Macintosh
1Place the CD-ROM in the CD-ROM drive.
2Double-click SAMSUNG_CLP on your Macintosh desktop.
3Double-click User’s Guide folder.
4Double-click User’s Guide.pdf(language). The Adobe 
Acrobat programme opens and you can view the User’s 
Guide.
%ownloadedd/romd“anuals@rinterbcomd“anuals 
						

							SETUP GUIDE22
Using a network antenna
If you install the wired/wireless network card, you can use your 
printer in wireless environment.
For details about installing the wired/wireless network card, see 
the User’s Guide of your printer in the CD-ROM.
NOTE: After connecting the printer you need to configure the 
network parameters on the control panel. See the User’s Guide of 
your printer. You can use the software supplied with the card. 
Refer to the software User’s Guide. 
Step 6. Turning the Printer On
1Plug the power cord into the power receptacle on the back 
of the printer. 
2Plug the other end into a properly grounded AC outlet and 
turn on the power. 
CAUTIONS:
• Some parts inside of the printer may be hot when power is on or 
after printing. Be careful not to burn yourself when working 
inside the printer.
• Do not disassemble the printer when it is powered on. Doing so 
may give you an electric shock.
2
1
Downloaded From ManualsPrinter.com Manuals 
						

							SETUP GUIDE9
English
6Hold the handle on the imaging unit with the green roller 
facing you. Align the imaging unit with the slots in your 
printer so that the colors on both sides of the imaging unit 
slide into the corresponding colors of the slots.
CAUTION: Insert the imaging unit carefully so as not to scratch 
and damage the surface of the green roller.
7Slide the imaging unit down into the printer until it cannot 
be pushed in any further and fold the handle down. 
CAUTION: To prevent damage, do not expose the imaging unit to 
light for more than a few minutes. Close the top and left cover 
should the setup need to be halted for any reason.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: Keep the transfer belt level, do not turn the transfer belt 
over otherwise looses toner may be spilled.
13Slide the transfer belt down into the printer. Press it firmly 
to make sure that it latches into place.
%ownloadedd/romd“anuals@rinterbcomd“anuals
CAUTION: Do not use sharp objects, such as a knife or scissors, 
to open the toner cartridges packages. You could damage the 
surface of the toner cartridges.
17Holding both sides of the cartridges, gently roll them from 
side to side to distribute the toner.
18Place the toner cartridges on a flat surface as shown and 
remove the paper covering on the toner cartridge by 
removing the tape.
NOTE: If toner gets on your clothing, wipe it off with a dry cloth 
and wash it in cold water. Hot water sets toner into fabric.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: When printing text at 5% coverage, you can expect a 
toner cartridge life of about 7,000 pages for black and 5,000 pages 
for color. 
%ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
TEUP: Connecting the printer to the USB port of the computer 
requires a certified USB cable. You will need to buy a USB 2.0 
compliant cable that is within 3m in length. 
1Make sure that both the printer and the computer are 
turned off.
2Plug the USB printer cable into the connector on the back of 
the printer. 
3Connect the other end of the cable to the USB port on your 
computer. 
See the User’s Guide of your computer, if you need help.
NOTE: To print using the USB interface, you must run Windows 
98/Me/2000/XP, or Macintosh with OS 8.6~9.2/10.1~10.3.
To the USB port on 
your computer
%ownloadedd/romd“anuals@rinterbcomd“anuals
To the network 
LAN connection
%ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: For Windows NT 4.0/2000/XP, the system administrator 
should install the software. 
All applications should be closed on your PC before beginning 
installation. 
1Place the CD-ROM in the CD-ROM drive. Installation will 
start automatically.
If the CD-ROM drive does not automatically run:
Select Run from the Start menu, and type x:\Setup.exe 
in the Open box (where x is the drive letter for the CD-ROM 
drive), then click OK.
NOTE: If the New Hardware Found window appears during the 
installation procedure, click   in the upper right corner of the box, 
or click Cancel. 
ItemRequirements
Operating systemWindows 95/98/Me/NT 4.0/2000/XP
RAM95/98/Me 32 MB
NT 4.0/2000 64 MB
XP 128 MB
Free disk space95/98/Me/NT 4.0/
2000/XP300 MB
Internet Explorer 5.0 or higher

Downloaded From ManualsPrinter.com ManualsDownloaded From ManualsPrinter.com Manuals
NOTE: If your printer is not connected to the computer, the 
Connect Samsung CLP-550 Series window opens. After connecting 
the printer, click Next.
4Select the components you want to reinstall and click Next.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: If your computer doesn’t have Adobe Acrobat, selecting 
the View User’s Guide option automatically installs Adobe 
Acrobat for you. After installing is complete, repeats step 1 and 2. 
In Macintosh
1Place the CD-ROM in the CD-ROM drive.
2Double-click SAMSUNG_CLP on your Macintosh desktop.
3Double-click User’s Guide folder.
4Double-click User’s Guide.pdf(language). The Adobe 
Acrobat programme opens and you can view the User’s 
Guide.
%ownloadedd/romd“anuals@rinterbcomd“anuals 
						

							SETUP GUIDE24
Step 9. Installing the Printer Software 
The supplied CD-ROM contains Windows printing software, 
Macintosh printing software, Linux printing software, Win RCP 
(Remote Control Panel), on-line User’s Guide and Acrobat 
Reader to view the User’s Guide. 
If you are printing from Windows:
You can install the following printer software using the CD-ROM. 
•PostScript Printer Description (PPD) file for Windows to 
allow installation of the PostScript driver. For information 
about installing the PostScript driver, refer to Appendix B in 
the User’s Guide. 
•Samsung Proprietary printer driver for Windows. Use this 
driver to take full advantage of your printer’s features. See 
page 25.
•USB driver only for Windows 98/Me/2000/XP. For details 
about installing the USB driver, see page 25. 
•Remote Control Panel for DOS applications. This Windows-
based program is automatically installed when you install the 
printer driver. For information about using the program, refer 
to Appendix D in the User’s Guide.
If you are printing from Macintosh:
For information about installing the print software and printing 
from a Macintosh, refer to Appendix A in the User’s Guide. To 
view the User’s Guide, see page 31.
If you are printing in Linux:
For information about installing the Linux driver, refer to 
Appendix B in the User’s Guide. To view the User’s Guide, see 
page 32.
%ownloadedd/romd“anuals@rinterbcomd“anuals 
						

							SETUP GUIDE9
English
6Hold the handle on the imaging unit with the green roller 
facing you. Align the imaging unit with the slots in your 
printer so that the colors on both sides of the imaging unit 
slide into the corresponding colors of the slots.
CAUTION: Insert the imaging unit carefully so as not to scratch 
and damage the surface of the green roller.
7Slide the imaging unit down into the printer until it cannot 
be pushed in any further and fold the handle down. 
CAUTION: To prevent damage, do not expose the imaging unit to 
light for more than a few minutes. Close the top and left cover 
should the setup need to be halted for any reason.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: Keep the transfer belt level, do not turn the transfer belt 
over otherwise looses toner may be spilled.
13Slide the transfer belt down into the printer. Press it firmly 
to make sure that it latches into place.
%ownloadedd/romd“anuals@rinterbcomd“anuals
CAUTION: Do not use sharp objects, such as a knife or scissors, 
to open the toner cartridges packages. You could damage the 
surface of the toner cartridges.
17Holding both sides of the cartridges, gently roll them from 
side to side to distribute the toner.
18Place the toner cartridges on a flat surface as shown and 
remove the paper covering on the toner cartridge by 
removing the tape.
NOTE: If toner gets on your clothing, wipe it off with a dry cloth 
and wash it in cold water. Hot water sets toner into fabric.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: When printing text at 5% coverage, you can expect a 
toner cartridge life of about 7,000 pages for black and 5,000 pages 
for color. 
%ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
TEUP: Connecting the printer to the USB port of the computer 
requires a certified USB cable. You will need to buy a USB 2.0 
compliant cable that is within 3m in length. 
1Make sure that both the printer and the computer are 
turned off.
2Plug the USB printer cable into the connector on the back of 
the printer. 
3Connect the other end of the cable to the USB port on your 
computer. 
See the User’s Guide of your computer, if you need help.
NOTE: To print using the USB interface, you must run Windows 
98/Me/2000/XP, or Macintosh with OS 8.6~9.2/10.1~10.3.
To the USB port on 
your computer
%ownloadedd/romd“anuals@rinterbcomd“anuals
To the network 
LAN connection
%ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: For Windows NT 4.0/2000/XP, the system administrator 
should install the software. 
All applications should be closed on your PC before beginning 
installation. 
1Place the CD-ROM in the CD-ROM drive. Installation will 
start automatically.
If the CD-ROM drive does not automatically run:
Select Run from the Start menu, and type x:\Setup.exe 
in the Open box (where x is the drive letter for the CD-ROM 
drive), then click OK.
NOTE: If the New Hardware Found window appears during the 
installation procedure, click   in the upper right corner of the box, 
or click Cancel. 
ItemRequirements
Operating systemWindows 95/98/Me/NT 4.0/2000/XP
RAM95/98/Me 32 MB
NT 4.0/2000 64 MB
XP 128 MB
Free disk space95/98/Me/NT 4.0/
2000/XP300 MB
Internet Explorer 5.0 or higher

Downloaded From ManualsPrinter.com ManualsDownloaded From ManualsPrinter.com Manuals
NOTE: If your printer is not connected to the computer, the 
Connect Samsung CLP-550 Series window opens. After connecting 
the printer, click Next.
4Select the components you want to reinstall and click Next.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: If your computer doesn’t have Adobe Acrobat, selecting 
the View User’s Guide option automatically installs Adobe 
Acrobat for you. After installing is complete, repeats step 1 and 2. 
In Macintosh
1Place the CD-ROM in the CD-ROM drive.
2Double-click SAMSUNG_CLP on your Macintosh desktop.
3Double-click User’s Guide folder.
4Double-click User’s Guide.pdf(language). The Adobe 
Acrobat programme opens and you can view the User’s 
Guide.
%ownloadedd/romd“anuals@rinterbcomd“anuals 
						

							SETUP GUIDE26
2When the following window opens, connect your printer to 
the computer and turn the printer on. Then click Next.
If the printer is already connected and turned on, this 
screen does not appear. Skip to the next step.
3Choose the installation type. 
•Auto Install: Installs the common software for your 
printer, such as printer driver, USB driver, PS driver and 
User’s Guide. This is recommended for most users.
%ownloadedd/romd“anuals@rinterbcomd“anuals 
						

							SETUP GUIDE9
English
6Hold the handle on the imaging unit with the green roller 
facing you. Align the imaging unit with the slots in your 
printer so that the colors on both sides of the imaging unit 
slide into the corresponding colors of the slots.
CAUTION: Insert the imaging unit carefully so as not to scratch 
and damage the surface of the green roller.
7Slide the imaging unit down into the printer until it cannot 
be pushed in any further and fold the handle down. 
CAUTION: To prevent damage, do not expose the imaging unit to 
light for more than a few minutes. Close the top and left cover 
should the setup need to be halted for any reason.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: Keep the transfer belt level, do not turn the transfer belt 
over otherwise looses toner may be spilled.
13Slide the transfer belt down into the printer. Press it firmly 
to make sure that it latches into place.
%ownloadedd/romd“anuals@rinterbcomd“anuals
CAUTION: Do not use sharp objects, such as a knife or scissors, 
to open the toner cartridges packages. You could damage the 
surface of the toner cartridges.
17Holding both sides of the cartridges, gently roll them from 
side to side to distribute the toner.
18Place the toner cartridges on a flat surface as shown and 
remove the paper covering on the toner cartridge by 
removing the tape.
NOTE: If toner gets on your clothing, wipe it off with a dry cloth 
and wash it in cold water. Hot water sets toner into fabric.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: When printing text at 5% coverage, you can expect a 
toner cartridge life of about 7,000 pages for black and 5,000 pages 
for color. 
%ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
TEUP: Connecting the printer to the USB port of the computer 
requires a certified USB cable. You will need to buy a USB 2.0 
compliant cable that is within 3m in length. 
1Make sure that both the printer and the computer are 
turned off.
2Plug the USB printer cable into the connector on the back of 
the printer. 
3Connect the other end of the cable to the USB port on your 
computer. 
See the User’s Guide of your computer, if you need help.
NOTE: To print using the USB interface, you must run Windows 
98/Me/2000/XP, or Macintosh with OS 8.6~9.2/10.1~10.3.
To the USB port on 
your computer
%ownloadedd/romd“anuals@rinterbcomd“anuals
To the network 
LAN connection
%ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: For Windows NT 4.0/2000/XP, the system administrator 
should install the software. 
All applications should be closed on your PC before beginning 
installation. 
1Place the CD-ROM in the CD-ROM drive. Installation will 
start automatically.
If the CD-ROM drive does not automatically run:
Select Run from the Start menu, and type x:\Setup.exe 
in the Open box (where x is the drive letter for the CD-ROM 
drive), then click OK.
NOTE: If the New Hardware Found window appears during the 
installation procedure, click   in the upper right corner of the box, 
or click Cancel. 
ItemRequirements
Operating systemWindows 95/98/Me/NT 4.0/2000/XP
RAM95/98/Me 32 MB
NT 4.0/2000 64 MB
XP 128 MB
Free disk space95/98/Me/NT 4.0/
2000/XP300 MB
Internet Explorer 5.0 or higher

Downloaded From ManualsPrinter.com ManualsDownloaded From ManualsPrinter.com Manuals
NOTE: If your printer is not connected to the computer, the 
Connect Samsung CLP-550 Series window opens. After connecting 
the printer, click Next.
4Select the components you want to reinstall and click Next.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: If your computer doesn’t have Adobe Acrobat, selecting 
the View User’s Guide option automatically installs Adobe 
Acrobat for you. After installing is complete, repeats step 1 and 2. 
In Macintosh
1Place the CD-ROM in the CD-ROM drive.
2Double-click SAMSUNG_CLP on your Macintosh desktop.
3Double-click User’s Guide folder.
4Double-click User’s Guide.pdf(language). The Adobe 
Acrobat programme opens and you can view the User’s 
Guide.
%ownloadedd/romd“anuals@rinterbcomd“anuals 
						

							SETUP GUIDE28
Otherwise, just click Finish.
NOTES:
• When you want to use your printer with the parallel cable, 
remove the USB cable and connect the parallel cable. Then 
repair the printer driver; select Start  Programs  Samsung 
CLP-550 Series  Printer Maintenance  Repair  Printer. 
If you have replaced the parallel cable with the USB cable, do the 
same to repair the driver.
• If your printer doesn’t work properly, reinstall the printer driver.
• You can also print from Macintosh or Linux. For detailed 
information, refer to the User’s Guide of the printer. 
• After installation of the software, you can reinstall or remove the 
printer software, if necessary. Also, you can change the display 
language. For detailed information, see page 29 ~ page 30.
%ownloadedd/romd“anuals@rinterbcomd“anuals 
						

							SETUP GUIDE9
English
6Hold the handle on the imaging unit with the green roller 
facing you. Align the imaging unit with the slots in your 
printer so that the colors on both sides of the imaging unit 
slide into the corresponding colors of the slots.
CAUTION: Insert the imaging unit carefully so as not to scratch 
and damage the surface of the green roller.
7Slide the imaging unit down into the printer until it cannot 
be pushed in any further and fold the handle down. 
CAUTION: To prevent damage, do not expose the imaging unit to 
light for more than a few minutes. Close the top and left cover 
should the setup need to be halted for any reason.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: Keep the transfer belt level, do not turn the transfer belt 
over otherwise looses toner may be spilled.
13Slide the transfer belt down into the printer. Press it firmly 
to make sure that it latches into place.
%ownloadedd/romd“anuals@rinterbcomd“anuals
CAUTION: Do not use sharp objects, such as a knife or scissors, 
to open the toner cartridges packages. You could damage the 
surface of the toner cartridges.
17Holding both sides of the cartridges, gently roll them from 
side to side to distribute the toner.
18Place the toner cartridges on a flat surface as shown and 
remove the paper covering on the toner cartridge by 
removing the tape.
NOTE: If toner gets on your clothing, wipe it off with a dry cloth 
and wash it in cold water. Hot water sets toner into fabric.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: When printing text at 5% coverage, you can expect a 
toner cartridge life of about 7,000 pages for black and 5,000 pages 
for color. 
%ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
TEUP: Connecting the printer to the USB port of the computer 
requires a certified USB cable. You will need to buy a USB 2.0 
compliant cable that is within 3m in length. 
1Make sure that both the printer and the computer are 
turned off.
2Plug the USB printer cable into the connector on the back of 
the printer. 
3Connect the other end of the cable to the USB port on your 
computer. 
See the User’s Guide of your computer, if you need help.
NOTE: To print using the USB interface, you must run Windows 
98/Me/2000/XP, or Macintosh with OS 8.6~9.2/10.1~10.3.
To the USB port on 
your computer
%ownloadedd/romd“anuals@rinterbcomd“anuals
To the network 
LAN connection
%ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: For Windows NT 4.0/2000/XP, the system administrator 
should install the software. 
All applications should be closed on your PC before beginning 
installation. 
1Place the CD-ROM in the CD-ROM drive. Installation will 
start automatically.
If the CD-ROM drive does not automatically run:
Select Run from the Start menu, and type x:\Setup.exe 
in the Open box (where x is the drive letter for the CD-ROM 
drive), then click OK.
NOTE: If the New Hardware Found window appears during the 
installation procedure, click   in the upper right corner of the box, 
or click Cancel. 
ItemRequirements
Operating systemWindows 95/98/Me/NT 4.0/2000/XP
RAM95/98/Me 32 MB
NT 4.0/2000 64 MB
XP 128 MB
Free disk space95/98/Me/NT 4.0/
2000/XP300 MB
Internet Explorer 5.0 or higher

Downloaded From ManualsPrinter.com ManualsDownloaded From ManualsPrinter.com Manuals
NOTE: If your printer is not connected to the computer, the 
Connect Samsung CLP-550 Series window opens. After connecting 
the printer, click Next.
4Select the components you want to reinstall and click Next.
%ownloadedd/romd“anuals@rinterbcomd“anuals
NOTE: If your computer doesn’t have Adobe Acrobat, selecting 
the View User’s Guide option automatically installs Adobe 
Acrobat for you. After installing is complete, repeats step 1 and 2. 
In Macintosh
1Place the CD-ROM in the CD-ROM drive.
2Double-click SAMSUNG_CLP on your Macintosh desktop.
3Double-click User’s Guide folder.
4Double-click User’s Guide.pdf(language). The Adobe 
Acrobat programme opens and you can view the User’s 
Guide.
%ownloadedd/romd“anuals@rinterbcomd“anuals 
						

							SETUP GUIDE30
5If you select Printer, follow steps 4 and 5 on page 27. 
6When the reinstallation is done, click Finish.
Removing Printer software
1From the Start menu, select Programs.
2Select Samsung CLP-550 Series, and then Printer 
Maintenance.
3Select Remove and then click Next.
4Select the components you want to remove and then click 
Next.
5After the software is removed, click Finish.
Changing the Display Language
After installation of the software, you can change the display 
language. 
1From the Start menu, select Programs.
2Select Samsung CLP-550 Series, and Language 
Selection.
3Select the desired language from the language selection 
window, and click OK. 
%ownloadedd/romd“anuals@rinterbcomd“anuals