Samsung C460 User Guide
Have a look at the manual Samsung C460 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Media and tray 412. Menu Overview and Basic Setup 5 Place the paper with the side you want to print facing up. For paper smaller than Letter-sized, press and unlatch the guide lock in the tray, push the tray in manually. Then adjust the paper length guide and paper width guide. For paper longer than Legal-sized, press and unlatch the guide lock in the tray, pull the tray out manually. Then adjust the paper length guide and paper width guide. • Do not push the paper width guide too far causing the media to warp. • Do not use a paper with a leading-edge curl, it may caus e a paper jam or the paper can be wrinkled. • If you do not adjust the paper width guide, it may cause paper jams. 2 1 2 1
Media and tray 422. Menu Overview and Basic Setup 6 Squeeze the paper width guide and slide it to the edge of the paper stack without causing it to bend. 7 Close the paper cover. 8 Insert the paper tray. 9 When you print a document, set the pa per type and size for the tray (see "Setting the paper size and type" on page 46). The tray is preset to Letter or A4 size, depending on yo ur country. To change the size to A4 or Letter, yo u must adjust the lever and paper width guide properly.
Media and tray 432. Menu Overview and Basic Setup 1Pull the tray out of the machine. Open the paper cover and remove paper from the tray if necessary. 2 If you want to change the size to Letter, hold the lever at the back of the tray, and rotate th e lever clockwise. 3 Squeeze the paper width guide and sl ide it to the edge of the lever. If you want to change the size to A4, first move the paper width guide to left and rotate the lever counterclockwise. If you force the lever, it could damage the tray. LTRA4 LT RA4
Media and tray 442. Menu Overview and Basic Setup 4 Printing on special media The table below shows the special media usable in tray. The paper setting in the machine and dri ver should match to print without a paper mismatch error. To change the paper setting set in the machine, from the Samsung Easy Printer Manager select (Switch to advanced mode) > Device Settings . Or if your machine supports a display screen, you can set it using the (Menu) button on the control panel. Then, set the paper type from the Printing preferences window > Paper tab > Paper Type (see "Opening printing pr eferences" on page 54). • When using special media, we recommend you feed one sheet at a time (see "Print media specifications" on page 117). • Illustrations on this user’s gu ide may differ from your machine depending on its options or mode ls. Check your machine type (see "Front view" on page 20). To see paper weights for each sheet, refer to "Print media specifications" on page 117. ( ● : Supported, Blank: Not supported) TypesTraya a. The paper types available manual feeding in tray. Plain ● Thick ● Thin ● Bond ● Color ● CardStock ● Labels ● Preprinted ● Cotton ● Recycled ● Archive ● Glossy Photo ● Matte Photo ●
Media and tray 452. Menu Overview and Basic Setup Labels To avoid damaging the machine, use only labels designed for use in laser printers. • When selecting labels, cons ider the following factors: - Adhesives: Should be stable at your machine’s fusing temperature about 170°C (338°F). - Arrangement: Only use labels with no exposed backing between them. Labels can peel off sheets that have spaces between the labels, causing \я serious jams. - Curl: Must lie flat with no more than 13 mm of curl in any direction. - Condition: Do not use labels with wr inkles, bubbles, or other indications of separation. • Make sure that there is no exposed adhesive material between labels. Exposed areas can cause labels to peel off during printing, which can cause paper jams. Exposed adhesive can also cause damage to machine components. • Do not run a sheet of labels throug h the machine more than once. The adhesive backing is designed for on ly a single pass through the machine. • Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged. Card stock/ Custom-sized paper • In the software application, set the margins to at least 6.4 mm (0.25 inches) away from the edges of the material.
Media and tray 462. Menu Overview and Basic Setup Preprinted paper When loading preprinted paper, the printed side should be facing up with an uncurled edge at the front. If you expe rience problems with paper feeding, turn the paper around. Note that pr int quality is not guaranteed. • Must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when sub jected to the machine’s fusing temperature for 0.1 second (about 170°C (338°F)). • Preprinted paper ink m ust be non-flammable and should not adversely affect machine rollers. • Before you load preprinted paper, verify that the ink on the paper is dry. During the fusing process, wet ink can come off preprinted paper, reducing print quality. 5 Setting the paper size and type After loading paper in the paper tray, set the paper size and type using the control panel buttons. • The paper setting in the machine and driver should match to print without a paper mismatch error. To change the paper setting se t in the machine, from the Samsung Easy Printer Manager select (Switch to advanced mode) > Device Settings . Or if your machine supports a display screen, you can set it using the (Menu ) button on the control panel. Then, set the paper type from the Printing preferences window > Paper tab > Paper Type (see "Opening printing preferences" on page 54). • It may be necessary to press OK to navigate to lower-level menus for some models. 1Select ( Menu) button on the control panel. 2 Press System Setup > Paper Setup > Paper Size or Paper Type. 3 Select the tray and the option you want. 4 Press OK to save the selection.
Media and tray 472. Menu Overview and Basic Setup 5 Press (Stop/Clear ) to return to ready mode. • If you want to use special-sized pape r such as billing paper, select the Paper tab > Size > Edit... and set Custom Paper Size Settings in the Printing Preferences (see "Opening printing preferences" on page 54). 6 Using the output support The surface of the output tray may become hot if you print a large number of pages at once. Make sure that you do not touch the surface, and do not allow children near it. The printed pages stack on the output support, and the output support will help the printed pages to align. The printer sends output to the output tray by default. Illustrations on this user’s guide ma y differ from your machine depending on its options or models. Check your machine type (see "Front view" on page 20).
Media and tray 482. Menu Overview and Basic Setup 7 Preparing originals • Do not load paper smaller than 142 x 148 mm (5.6 x 5.8 inches) or larger than 216 x 356 mm (8.5 x 14 inches). • Do not attempt to load the following s of paper, in order to prevent paper jam, low print quali ty and machine damage. - Carbon-paper or carbon-backed paper - Coated paper - Onion skin or thin paper - Wrinkled or creased paper - Curled or rolled paper - Torn paper • Remove all staples and pa per clips before loading. • Make sure any glue, ink, or correction fluid on the paper is completely dry before loading. • Do not load originals that include different sizes or weights of paper. • Do not load booklets, pamph lets, transparencies, or documents with other unusual characteristics. 8 Loading originals You can use the scanner glass or the docum ent feeder to load an original for copying, scanning, and sending a fax. Illustrations on this user’s guide ma y differ from your machine depending on its options or models. Check your machine type (see "Front view" on page 20). On the scanner glass Using the scanner glass, you can copy or scan originals. You can get the best scan quality, especially for colored or gray-scaled images. Make sure that no originals are in the document feeder. If an original is detected in the \яdocument feeder, the machine gives it priority over the original on the scanner glass.
Media and tray 492. Menu Overview and Basic Setup 1Lift and open the scanner lid.2 Place the original face down on the scanner glass. Align it with the registration guide at the t op left corner of the glass. 3 Close the scanner lid.
Media and tray 502. Menu Overview and Basic Setup • Leaving the scanner lid open while copying may affect copy quality and toner consumption. • Dust on the scanner glass may cause black spots on the printout. Always keep it clean (see "Cleaning the machine" on page 89). • If you are copying a page from a book or magazine, lift the scanner lid until its hinges are caught by the stopper and then close the lid. If the book or magazine is thicker than 30 mm, start copying with the scanner lid open. • Be careful not to break the sc anner glass. You may get hurt. • Do not put hands while closing the sc anner lid. The scanner lid may fall on your hands and get hurt. • Do not look into the light from insi de of the scanner while copying or scanning. It is harmful to eyes. In the document feeder 1Flex or fan the edge of the paper stack to separate the pages before loading originals. 2 Load the original face up into the document feeder input tray. Make sure that the bottom of the original stack matches th e paper size marked on the document input tray.