Runco X 450d Projector User Manual

							External Control
Runco X-400d/X-450d Installation/Operation Manual 115 
PREL
IMINARY
Remote Key Repeat (cont.) KRT W No 0 85 No 64 = Keypad Menu 
(used internally)
65 = Power Toggle 
(used internally)
66 = Enter Key Up (used internally)
67 = SRC 1
68 = SRC 2
69 = SRC 3
70 = SRC 4
71 = SRC 5
72 = SRC 6
73 = SRC 7
74 = SRC 8
75 = SRC 9
76 = SRC 10
77 = SRC 11
78 = SRC 12
79 = SRC 13
80 = SRC 14
81 = HDMI 5
82 = HDMI 6
83 = HDMI 7
84 = HDMI 8
85 = DisplayPort
86 = Auto Cinema
Language LAN R/W No 0 9 No 0 = English
1 = French
2 = German
3 = Italian
4 = Spanish
5 = Portuguese
6 = Simplified Chinese
7 = Traditional Chinese
8 = Swedish
9 = Russian
10 = Japanese
11 = Korean
Lens Home Position LHP W No N/A N/A No Action will be performed on any 
setting value
Lamp Hours Reset LHR W No N/A N/A No Action will be performed on any 
setting value
Lamp Hours LHS R No 0 (Note) No Max = 2,147,483,647
Image Alignment Left Middle x LMX R/W Yes -100 100 No
Image Alignment Left Middle y LMY R/W Yes -100 100 No
Lamp Life Notification Enable LNE R/W No 0 1 No 0 = Off; 1 = On
Lamp Life Notification Hours LNH R/W Yes 100 10,000 No
Logo LED Brightness LOG R/W Yes 0 31 No
Lamp Power LPW R/W Yes -1 0 No -1 = 230W; 0 = 260W
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
116 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Display Serial Number LSN R No N/A N/A Yes
Model Name MDL R No N/A N/A Yes
Memory Preset MMP R/W No 0 3 No 0 = ISF Night
1 = ISF Day
2 = Custom 1
3 = Custom 2
Memory Preset Copy MPC W No N/A N/A No
Action will be performed on any 
setting value
Memory Preset Paste MPP W No N/A N/A No
Memory Preset Reset MPR W No 0 3 No 0 = ISF Night
1 = ISF Day
2 = Custom 1
3 = Custom 2 Memory Preset Save MPS W No 0 3 No
Noise Filter NFL R/W Yes 0 10 No Calibration -> Input Color menu
Noise Filter Offset NFO R/W Yes 0 10 No Picture menu
Orientation ORI R/W No0 4 No 0 = Floor Front
1 = Ceiling Front
2 = Floor Rear
3 = Ceiling Rear
4 = Auto
OSD Position Horizontal OSD R/W Yes 0 100 No
Output Shift Height OSH R/W Yes -50 0 No
Output Shift Left Right OSL R/W Yes -300 300 No
OSD Message Enable OSM R/W No 0 1 No 0 = Off; 1 = On
OSD Timer OST R/W Yes 0 60 No Values from 1-4 are not allowed; if 
increment or decrement is used, 
these values will be skipped.
Output Shift Up Down OSU R/W Yes -200 200 No
OSD Position Vertical OSV R/W Yes 0 100 No
Output Shift Width OSW R/W Yes -50 0 No
Overscan Mode OVM R/W No 0 1 No 0 = Zoom
1 = Crop
Overscan OVS R/W Yes 0 20 No
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
Runco X-400d/X-450d Installation/Operation Manual 117 
PREL
IMINARY
Programmable Source Key 
[1 ... 14]P01
P02
P03
P04
P05
P06
P07
P08
P09
P10
P11
P12
P13
P14R/W No 0 15 No 0 = Composite 1
1 = Composite 2
2 = Composite 3
3 = Component
4 = HD 1
5 = HD 2
6 = SCART
7 = HDMI 1
8 = HDMI 2
9 = HDMI 3
10 = HDMI 4
11 = HDMI 5
12 = HDMI 6
13 = HDMI 7
14 = HDMI 8
15 = DisplayPort
PCE Cyan X PCX R/W Yes -100 100 No
PCE Cyan Y PCY R/W Yes -100 100 No
Phase PHS R/W Yes 0 31 No
PCE Magenta X PMX R/W Yes -100 100 No
PCE Magenta Y PMY R/W Yes -100 100 No
Periodic Notification Enable PNE R/W No 0 1 No 0 = Off; 1 = On
Periodic Notification Months PNM R/W Yes 1 255 No
Power PWR R/W No 0 1 No 0 = Off; 1 = On
PCE Yellow X PYX R/W Yes -100 100 No
PCE Yellow Y PYY R/W Yes -100 100 No
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
118 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Input Name 1 Restore R01 W No N/A N/A No
Action will be performed on any 
setting value Input Name 2 Restore R02 W No N/A N/A No
Input Name 3 Restore R03 W No N/A N/A No
Input Name 4 Restore R04 W No N/A N/A No
Input Name 5 Restore R05 W No N/A N/A No
Input Name 6 Restore R06 W No N/A N/A No
Input Name 7 Restore R07 W No N/A N/A No
Input Name 8 Restore R08 W No N/A N/A No
Input Name 9 Restore R09 W No N/A N/A No
Input Name 10 Restore R10 W No N/A N/A No
Input Name 11 Restore R11 W No N/A N/A No
Input Name 12 Restore R12 W No N/A N/A No
Input Name 13 Restore R13 W No N/A N/A No
Input Name 14 Restore R14 W No N/A N/A No
Input Name 15 Restore R15 W No N/A N/A No
Input Name 16 Restore R16 W No N/A N/A No
Remote Code RMN R/W Yes 0 65535 No
Image Alignment Right Middle x RMX R/W Yes -100 100 No
Remote Network Control RNC R/W No 0 1 No 0 = Off; 1 = On
Standby LED Enable SBL R/W No 0 1 No 0 = Off; 1 = On
Splash Configure String 1 SC1 R/W No N/A N/A Yes
30 characters max Splash Configure String 2 SC2 R/W No N/A N/A Yes
Splash Configure String 3 SC3 R/W No N/A N/A Yes
Sidebar Color Blue SCB R/W Yes 0 255 No
Sidebar Color Green SCG R/W Yes 0 255 No
Screen SCN R/W No 0 1 No 0 = Screen 1
1 = Screen 2
Sidebar Color Red SCR R/W Yes 0 255 No
Send Errors to Runco SER R/W No 0 1 No 0 = Off; 1 = On
Sharpness Offset SHO R/W Yes -50 50 No
Sharpness SHP R/W Yes -50 50 No
Screen Masking Bottom SMB R/W Yes 0 200 No
Screen Masking Test Pattern 
EnableSME R/W No 0 1 No 0 = Off; 1 = On
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
Runco X-400d/X-450d Installation/Operation Manual 119 
PREL
IMINARY
Screen Masking Left SML R/W Yes 0 200 No
Screen Masking Test Pattern 
Mode EnableSMM R/W No 0 1 No 0 = Off; 1 = On
Screen Masking Right SMR R/W Yes 0 200 No
Screen Masking Top SMT R/W Yes 0 200 No
Splash Enable SPE R/W No 0 1 No 0 = Off; 1 = On
Splash Timer SPT R/W Yes 5 60 No
Status STA RNo04No
Sync Threshold STH R/W Yes 0 15 No
Sleep Timer STM R/W No 0 5 No 0 = Off
1 = 30 Minutes
2 = 60 Minutes
3 = 90 Minutes
4 = 2 Hours
5 = 4 Hours
Subnet Mask Byte 1 SU1 R/W Yes 0 255 No
Subnet Mask Byte 2 SU2 R/W Yes 0 255 No
Subnet Mask Byte 3 SU3 R/W Yes 0 255 No
Subnet Mask Byte 4 SU4 R/W Yes 0 255 No
System Reset SYS W No N/A N/A No Action will be performed on any 
setting value
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
120 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Trigger 1 16:9 T11 R/W No 0 1 No
0 = Off; 1 = On Trigger 1 4:3 T12 R/W No 0 1 No
Trigger 1 Letterbox T13 R/W No 0 1 No
Trigger 1 VirtualWide T14 R/W No 0 1 No
Trigger 1 Cinema T15 R/W No 0 1 No
Trigger 1 Virtual Cinema T16 R/W No 0 1 No
Trigger 1 Native T17 R/W No 0 1 No
Trigger 2 16:9 T21 R/W No 0 1 No
Trigger 2 4:3 T22 R/W No 0 1 No
Trigger 2 Letterbox T23 R/W No 0 1 No
Trigger 2 VirtualWide T24 R/W No 0 1 No
Trigger 2 Cinema T25 R/W No 0 1 No
Trigger 2 Virtual Cinema T26 R/W No 0 1 No
Trigger 2 Native T27 R/W No 0 1 No
Trigger 3 16:9 T31 R/W No 0 1 No
Trigger 3 4:3 T32 R/W No 0 1 No
Trigger 3 Letterbox T33 R/W No 0 1 No
Trigger 3 VirtualWide T34 R/W No 0 1 No
Trigger 3 Cinema T35 R/W No 0 1 No
Trigger 3 Virtual Cinema T36 R/W No 0 1 No
Trigger 3 Native T37 R/W No 0 1 No
3D Test Pattern Enable TDE R/W No 0 1 No 0 = Off; 1 = On
3D Mode TDM R/W No 0 4 No 0 = Auto
1 = Off
2 = Side-by-Side
3 = Top-and-Bottom
4 = Frame Packing
3D Reverse Eyes TDR R/w No 0 1 No 0 = Off; 1 = On
Image Alignment Top Left x TLX R/W Yes -100 100 No
Image Alignment Top Left y TLY R/W Yes -100 100 No
3D Test Pattern Mode Enable TME R/W No 0 1 No 0 = Off; 1 = On
Image Alignment Top Middle x TMX R/W Yes -100 100 No
Image Alignment Top Middle y TMY R/W Yes -100 100 No
Tint Offset TNO R/W Yes -50 50 No Picture menu
Tint TNT R/W Yes -50 50 No Calibration -> Input Image menu
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
Runco X-400d/X-450d Installation/Operation Manual 121 
PREL
IMINARY
Test Pattern Enable TPE R/W No 0 1 No 0 = Off; 1 = On
Primary Test Pattern TPP R/W No 0 1 No 0 = Off; 1 = On
Secondary Test Pattern TPS R/W No 0 1 No 0 = Off; 1 = On
Tracking TRK R/W Yes -100 100 No
Image Alignment Top Right x TRX R/W Yes -100 100 No
Image Alignment Top Right y TRY R/W Yes -100 100 No
Test Video TST R/W No 0 4 No 1 = Color Bars 1
2 = Full White
11 = Color Bars 2
12 = Gray Bars
13 = Focus
14 = Off
15 = Off (Restore OSD)
16 = Primary Alignment
17 = Secondary Alignment
18 = Dual Alignment
19 = 3D
VFD Brightness VFD R/W Yes 0 4 No 0 = 0%
1 = 25%
2 = 50%
3 = 75%
4 = 100%
Vertical Shift VSH W Yes 0 0 No Send 
(VSH+) or (VSH-) to 
adjust incrementally 
Zoom ZOM W Yes 0 0 No Send 
(ZOM+) or (ZOM-) to 
adjust incrementally 
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
122 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
6.2 
Using Discrete IR 
CodesThe Dimension Digital Controller accepts commands in the form of IR signals that conform 
to the NEC protocol. Each Dimension Digital Controller remote control button has an NEC 
control code associated with it. 
You can use these codes to program a third-party, “universal” remote control unit to work 
with the Dimension Digital Controller. These third-party products usually come with a 
computer software application for this purpose. For more information, consult the 
documentation provided with the remote control unit. 
IR Command ProtocolThe IR control codes have the following characteristics:
 Each code consists of the following:
leader pulse (a modulated pulse of 9 ms followed by a non-modulated pulse of 
4.5 ms);
address bits. The default address is 82 09 (0x2011, binary 
00100000 00010001). To change it, select Remote Control from the Service menu 
and follow the steps given on page 87; 
data bits: eight (8) bits for the command followed by the logical inverse of the 
command; and
end pulse (a modulated pulse of 0.56 ms, similar to the modulated pulse in the 
‘0’ and ‘1’ bits).The end of the modulated pulse constitutes the end of the data 
transmission. 
 The carrier frequency is 38 kHz, with the modulated pulses having a 33% duty cycle. 
 Commands are sent at a maximum rate of 9 Hz.
For example, here is the NEC control code for the ON button on the Dimension Digital 
Controller remote control unit (assuming the default address is used):  
Figure 6-1 shows the pulse train for this command. 
Figure 6-1. NEC Protocol Message Format
➤
Hex201101FE
Binary
00100000 0001000100000001 11111110
Function Address Byte 1 Address Byte 2 CommandCommand
(Logical Inverse)
9 ms
13.5 ms 27 ms
27 ms Address Byte 1 Leader Pulse Address Byte 2 Command Byte Command Byte (logical inverse)
001 000000001 0001 00000001 1  1  1  1  1  1  1  04.5 msEnd Pulse 
						

							External Control
Runco X-400d/X-450d Installation/Operation Manual 123 
PREL
IMINARY
IR Command List 
(Standard Mode) Table 6-2 lists the NEC control codes for the Dimension Digital Controller. 
Table 6-2. NEC Control Codes for the Dimension Digital Controller 
(Standard Mode)
Remote 
Control 
Button NameAddressDataNEC Data 
From Remote 
(Note)Description
ON 8209 1 0x201101FE Power on
OFF (standby) 8209 2 0x201102FD Power off
16:9 8209 3 0x201103FC 16:9 aspect ratio
4:3 8209 4 0x201104FB 4:3 aspect ratio
LETBOX 8209 5 0x201105FA Letterbox aspect ratio
V-WIDE 8209 6 0x201106F9 VirtualWide aspect ratio
CINEMA 8209 7 0x201107F8 Cinema aspect ratio
V-CINE 8209 8 0x201108F7 Virtual Cinema aspect ratio
NATIVE 8209 9 0x201109F6 Native aspect ratio
1 8209 10 0x20110AF5 Number Button 1
2 8209 11 0x20110BF4 Number Button 2
3 8209 12 0x20110CF3 Number Button 3
4 8209 13 0x20110DF2 Number Button 4
5 8209 14 0x20110EF1 Number Button 5
6 8209 15 0x20110FF0 Number Button 6
7 8209 16 0x201110EF Number Button 7
8 8209 17 0x201111EE Number Button 8
9 8209 18 0x201112ED Number Button 9
0 8209 19 0x201113EC Number Button 0
ISF DAY 8209 20 0x201114EB ISF Day memory preset
ISF NIGHT 8209 21 0x201115EA ISF Night memory preset
SCREEN 1 8209 22 0x201116E9 Selects “Screen 1”
CUST 1 8209 23 0x201117E8 Custom 1 memory preset
CUST 2 8209 24 0x201118E7 Custom 2 memory preset
SCREEN 2 8209 25 0x201119E6 Selects “Screen 2”
MENU 8209 26 0x20111AE5MENU
EXIT 8209 27 0x20111BE4EXIT
Up 8209 28 0x20111CE3 Up-Arrow ( )
Note: These codes assume that the default address of 8209 is used. If you change it to something 
other than 8209, you will need to modify these codes accordingly.  
						

							External Control
124 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Right 8209 29 0x20111DE2 Right-Arrow ( ) 
Down 8209 30 0x20111EE1 Down-Arrow ( )
Left 8209 31 0x20111FE0 Left-Arrow ( )
ENTER 8209 32 0x201120DFENTER
SRC 1 8209 33 0x201121DE Video Source 1
SRC 2 8209 34 0x201122DD Video Source 2
SRC 3 8209 35 0x201123DC Video Source 3
SRC 4 8209 36 0x201124DB Video Source 4
SRC 5 8209 37 0x201125DA Video Source 5
SRC 6 8209 38 0x201126D9 Video Source 6
SRC 7 8209 39 0x201127D8 Video Source 7
SRC 8 8209 40 0x201128D7 Video Source 8
SRC 9 8209 41 0x201129D6 Video Source 9
SRC 10 8209 42 0x20112AD5 Video Source 10
SRC 11 8209 43 0x20112BD4 Video Source 11
SRC 12 8209 44 0x20112CD3 Video Source 12
SRC 13 8209 43 0x20112BD4 Video Source 13
SRC 14 8209 46 0x20112ED1 Video Source 14
3D AUTO 8209 47 0x20112FD0 3D Mode = Auto
3D SBS 8209 48 0x201130CF 3D Mode = Side-by-Side
3D TAB 8209 49 0x201131CE 3D Mode = Top-and-Bottom
3D FP 8209 50 0x201132CD 3D Mode = Frame Packing
STOFF 8209 65 0x201141BE Sets the sleep timer to Off
ST30MIN 8209 66 0x201142BD Sets the sleep timer to 30 minutes
ST60MIN 8209 67 0x201143BC Sets the sleep timer to 60 minutes
ST90MIN 8209 68 0x201144BB Sets the sleep timer to 90 minutes
ST2HRS 8209 69 0x201145BA Sets the sleep timer to 2 hours
ST4HRS 8209 70 0x201146B9 Sets the sleep timer to 4 hours
VIDEO 1 8209 71 0x201147B8 Composite video input 1
Table 6-2. NEC Control Codes for the Dimension Digital Controller 
(Standard Mode) (continued)
Remote 
Control 
Button NameAddressDataNEC Data 
From Remote 
(Note)Description
Note: These codes assume that the default address of 8209 is used. If you change it to something 
other than 8209, you will need to modify these codes accordingly.