Ricoh Projector PJ WX4152NI User Manual

• Entering the projector's PIN code in the access point
Enter the projector's PIN code in the access point so that the projector and the access point
authenticate and register each other. The projector's PIN code can be changed. For details
about entering the PIN code in the access point, see the manual provided with the access
point.
1. Select [Wireless LAN (Infrastructure)] on Network Setting Wizard, and then press the
[Enter] button. 2.
Select [Perform Simple Wireless LAN Setup], and then...

12.
Select [Continue Wizard] or [End Wizard] on the confirmation screen, and then press the
[Enter] button.
To proceed to the wired LAN settings, select [Continue Wizard]. For details about how to configure
the wired LAN settings, see page 67 "Configuring the Wired LAN Settings".
To end the network settings, select [End Wizard].
The wireless LAN setup is complete.
To project the image from a computer, see page 73 "Projecting a Computer's Screen via a
Network".
Configuring the settings...

4.
Enter the network key.
When connecting to a network for which a network key is not set, the network key input screen is
not displayed. Proceed to Step 5.
5. Select [Disable DHCP (Manual Settings)] or [Enable DHCP (Auto Settings)], and then press
the [Enter] button.
If you select [Enable DHCP (Auto Settings)], proceed to Step 10.
6. Specify the projector's IP address.
7. Specify the subnet mask.
8. Specify the default gateway.
9. If the message "To perform connection by WPA/WPA2-EAP, continuous...

2.
Select [Continue Wizard] or [End Wizard] on the confirmation screen, and then press the
[Enter] button.
To proceed to the wired LAN settings, select [Continue Wizard]. For details about how to configure
the wired LAN settings, see page 67 "Configuring the Wired LAN Settings".
To end the network settings, select [End Wizard].
The wireless LAN setup is complete.
To project the image from a computer, see page 73 "Projecting a Computer's Screen via a
Network".
. 5. Using the Projector...

Projecting a Computer's Screen via a Network
The projector does not support the Network Projector function of Windows. Use QuickProjection, which
is the application provided with the projector for projecting a computer's screen via a network.
This section explains how to use QuickProjection in Windows as an example. The basic operation flow is
the same as when a Mac OS is used.
How to Use QuickProjection QuickProjection is included on the supplied CD-ROM.
QuickProjection operating environment is...

To delete QuickProjection, click [Uninstall a program] in [Control Panel] of Windows, and then
select "RICOH QuickProjection" to uninstall the software.
Two versions of QuickProjection are available for Mac OS, one supports audio and the other does
not.
Projecting Images Using QuickProjection Before projecting images using QuickProjection, connect the projector to a network. For details about
how to connect the projector to a network, see page 66 "Connecting the Projector to a Network"....

6.
Enter the identification code on the QuickProjection dialog. The projector's name or IP address can also be entered instead of the identification code.
7. Click [Projection].
The computer's screen is projected.
While the computer's screen is being projected, a small QuickProjection is displayed in the lower
right corner of the computer's screen. To pause the projection, click .
To quit the projection, click [ ], and then click [OK].
• Two projection modes are available: “Presentation...

Projecting Images Using DLNA-Compatible
Devices
The projector is compatible with DLNA. DLNA is the guideline for sharing content on a network.
Therefore, the projector can project still images and videos transmitted from DLNA-compatible devices.
The projector can also access DLNA-compatible devices such as file servers, tablet computers, or smart
devices and project JPEG files stored on them.
The supported file types for the DLNA-compatible devices are shown below:
Still images
Item
Requirements
File...

• The supported video file types are compliant with the projector's own specifications. They are not
compliant with the DLNA 1.5 guidelines.
• The maximum number of files that can be displayed in the list is 512 per folder.
•
Characters that can be used for file names and folder names are single-byte letters and numbers
and characters used in the language specified in [Language] under [Default Settings 2]. If
characters for languages other than the language specified are used, the file name or folder...

The procedure of the DLNA-compatible device described below is an outline of the basic flow. The
detailed procedure varies depending on the device and application. For details, see the manuals
provided with the device and application.
1. Turn the projector on.
2. If [Network PC] is not selected as the input signal, press the [Input] button. 3.
Switch the input signal to [Network PC].
For details about how to switch the input signal, see page 35 "Projecting an Image".
The standby screen for...