Ricoh Caplio R30 User Guide

							139
Installing Software
Installing the Software on Your Computer
Caution
• Do not connect your camera to the computer until indicated. If you happened to connect 
your camera to the computer (resulting in the [Add New Hardware Wizard] screen 
appearing), simply click [Cancel], and after disconnecting your camera, install the software 
on your computer.
• If a message is displayed during installation to uninstall the old Caplio software before 
installing the new one, uninstall the old Caplio software once and install the new one again 
by following the message instructions. Even with the new Caplio software, however, the 
image downloading and other functions of the old model can still be used as before. (For 
how to uninstall the software, see P.151.)
• For Windows XP or Windows 2000, Administrator privileges are required to install the 
software.
Note
Here is an example of the Windows XP screen.
1.Start your computer and insert the 
Caplio CD-ROM in the CD-ROM 
drive.
The screen shown on the right appears 
automatically.
2.Click [Install the Software].
After a while, the [Select Setting 
Language] screen appears.
3.Confirm the language, and then click [OK].
After a few moments, the [Welcome to InstallShield Wizard] screen 
appears.
4.Click [Next].
After a few moments, the [Select 
Installation Destination] screen appears.
Downloaded From camera-usermanual.com Ricoh Manuals 
						

							140
5.Confirm where you want to install 
and then click [Next].
The [Select Program Folder] screen 
appears.
6.Confirm where you want to install 
and then click [Next].
The ImageMixer installer starts.
Install ImageMixer following the messages 
displayed on the screen.
When installation of ImageMixer is 
completed, a dialog appears to indicate 
that all software applications have been 
installed. 
7.Click [Finish].
8.Restart your computer.
Reference
For how to remove (uninstall) the software, see P.151.
Downloaded From camera-usermanual.com Ricoh Manuals 
						

							141
Installing Software
Installing the DeskTopBinder Lite
Reference
For how to use DeskTopBinder Lite, refer to the Beginner’s Guide, the Setup Guide, and the 
DeskTopBinder Lite - Auto Document Link Guide (all PDF files) that are installed with 
DeskTopBinder Lite.
Caution
• Do not connect your camera to the computer until indicated. If you happened to connect 
your camera to the computer (resulting in the [Add New Hardware Wizard] screen 
appearing), simply click [Cancel], and after disconnecting your camera, install the software 
on your computer.
• For Windows XP or Windows 2000, Administrator privileges are required to install the 
software.
Note
Here is an example of the Windows XP screen.
1.Start your computer and insert the 
Caplio CD-ROM in the CD-ROM 
drive.
The screen shown on the right appears 
automatically.
2.Click [Installing DeskTopBinder 
Lite].
After a few moments, the [Welcome to 
InstallShield Wizard] screen appears.
3.Click [Next].
After a few moments, the [Select Installation Destination] screen appears.
4.Confirm where you want to install 
and then click [Next].
The [Select Program Folder] screen 
appears.
5.Confirm where you want to install 
and then click [Next].
Downloaded From camera-usermanual.com Ricoh Manuals 
						

							142
6.Click [OK].
7.Click [DeskTopBinder Lite].
The DeskTopBinder Lite installer starts.
Install DeskTopBinder Lite following the messages displayed on the 
screen.
When the screen where you verify digital ID is displayed, click OK.
Caution
• When capturing images from the camera using the Auto Document link of the 
DeskTopBinder Lite, deselect the [Automatically save on connection] check box in the 
[Optional Settings] dialog box displayed by selecting [Optional Settings] on the [RICOH 
Gate La Settings] menu. (Refer to the Software User Guide.) Before capturing images from 
the camera, set the date and time using the DATE SETTINGS option of the camera. 
(P.122)
• If you turned off and on the camera connected to the computer with the DeskTopBinder Lite 
in open state, reboot the computer with the camera connected.
Downloaded From camera-usermanual.com Ricoh Manuals 
						

							143
Installing Software
Connecting the Camera to Your Computer
Downloading Images Using RICOH Gate La
After installing the software on your computer, connect your camera 
to the computer.
The following explanation is provided assuming that [ORIGINAL] 
(default) is selected at [USB CONNECTION] of the camera’s Setup 
menu (P.127). If [MASS STR] is selected, change it to [ORIGINAL].
1.Make sure the camera power is off.
2.Connect the USB cable to the 
USB port of your computer.
3.Connect the USB cable to the 
USB terminal of your camera.
Your camera turns on.
Downloaded From camera-usermanual.com Ricoh Manuals 
						

							144
For Windows XP
The first time you connect your camera to the computer using a USB 
cable, the [Found New Hardware Wizard] screen will appear.
1.Select [Install the software 
automatically (Recommended)].
2.Insert the Caplio Software CD-ROM into the CD-ROM drive 
on your computer.
Installation of the WIA Driver automatically starts. If the CD-ROM is 
already on your computer when the [Found New Hardware Wizard] 
window is displayed, simply click [Next] to start installation.
Reference
For how to turn the camera on/off, see P.22.
Note
By default, the WIA driver is installed in the following location:
Specify the folder if the CD-ROM is not available.
My Computer
Local Disk
Program Files
Caplio Software
WIA Driver
Downloaded From camera-usermanual.com Ricoh Manuals 
						

							145
Installing Software
3.Select [RICOH Gate La], check 
[Always use this program for this 
action] check box, and then click 
[OK].
To load images from the camera with 
assistance from the Windows XP Scanner and Camera Wizard, select 
[Scanner and Camera Wizard].
Leaving the [Always use this program for this action] check box 
unchecked will cause the [Caplio R3] screen to be displayed each time 
you transfer images from the camera, thereby allowing you to choose 
whether to use RICOH Gate La or the Scanner and Camera Wizard for 
image transfers.
If your PC is installed with Windows XP Service Pack2 and a warning 
message is displayed, see P.165.
Disconnecting the Camera from Your Computer:
1.Turn your camera off by pressing the power button.
2.Unplug the USB cable.
Note
• If the computer does not recognize the camera, uninstall the software (P.151) and install it 
again.
• When downloading images from the camera, use of the AC adapter (sold separately) is 
recommended.
Reference
• For how to turn the camera on/off, see P.22.
• For details about [USB CONNECTION](MASS STR/Original), see P.127.
Downloaded From camera-usermanual.com Ricoh Manuals 
						

							146
Transferring Images in Mass Storage Mode
Caution
Windows 98/98 SE and Mac OS 8.6 are not compatible with Mass Storage Mode.
1.Change [USB CONNECTION] to [MASS STR] on the Setup 
menu.
For more details, see P.127. At the time of purchase, [ORIGINAL] is 
selected.
2.Make sure that the camera power is off.
3.Connect the accessory USB cable to a USB port of your 
computer.
4.Connect the USB cable to the USB 
terminal of your camera.
Your camera turns on.
Your computer automatically reads a file 
necessary for recognizing the camera as a 
drive. 
After this preparation, the camera is 
displayed as a drive at My Computer 
(Windows) or Desktop (Macintosh).
5.From the displayed drive, 
copy a file to the desired 
location.
The figure at right shows the folder 
configuration in the drive.
When the contents of the built-in 
memory are displayed, the drive 
name is RICOHDCI.
Caution
During transfer, do not disconnect the USB cable.
Note
When an SD memory card is inserted, its files are displayed. Otherwise, files in the built-in 
memory are displayed.
Example of the display in 
Windows XP
Downloaded From camera-usermanual.com Ricoh Manuals 
						

							147
Installing Software
Disconnecting the Camera from Your Computer 
(Windows)
The display is an example of Windows XP. The terms are different 
for other operating systems but the operations are the same.
1.Click the Remove Hardware Safely icon at the right end of 
the task bar.
2.Select [USB Large-capacity Storage Device] and click 
[Stop].
3.Check that [USB Large-capacity Storage Device] is selected 
and click [OK].
4.Click [OK].
Disconnecting the Camera from Your Computer 
(Macintosh)
1.Put the displayed drive in the Recycle Bin.
Downloaded From camera-usermanual.com Ricoh Manuals 
						

							148
Downloading Images from an SD Memor y 
Card 
It is possible to download images from an SD memory card to the 
computer via a PC card slot or card reader.
To load an SD memory Card into a PC card slot or card reader, use 
the PC card adapter.
Images in an SD Memory Card
Images are stored in an SD Memory Card in a hierarchy shown 
below.
Note
If the card reader is SD memory card compatible (directly loadable), no PC card adapter is 
required.
Te r m
Card Reader
This is a device connected to a computer to read the contents of cards. In addition to the PC 
card type, there are card readers compatible with various types of cards, into which you can 
directly load a memory card.
Image files
Downloaded From camera-usermanual.com Ricoh Manuals